Waves H-Reverb on Behringer X32 and Waves SuperRack Performer

Рет қаралды 13,863

Күн бұрын

In this video I show you how to use Waves H-Reverb and Waves H-Delay on the Behringer X32 using Waves SuperRack Performer.
Learn more about my X32 Fundamentals course at: course.drewbrashler.com.
Check out Waves SuperRack Performer: waves.alzt.net/zNjbyM
Products shown in this video:
Behringer X32: sweetwater.sjv.io/g1RvM9
Behringer X-Live Expansion Card: sweetwater.sjv.io/oqNjmm
Waves SuperRack Performer: waves.alzt.net/zNjbyM
Waves H-Reverb: waves.alzt.net/5g7Zm3
Waves H-Delay: waves.alzt.net/AWE3kN
Chapters:
00:00 Intro
00:17 Waves Reverb with Behringer X32 Overview
01:20 Setup on the Behringer X32
04:30 Waves SuperRack Performer Routing for Waves Reverb with Behringer X32
07:20 Setting Up Waves H-Delay with Behringer X32
08:53 My Favorite Waves H-Delay Settings
09:50 Pro Tip: Feed Your Delay Into Your Verb
10:54 Conclusion

Пікірлер: 42

@Tabzunderground 19 күн бұрын

This dope

@alexnomundo 2 ай бұрын

I Love you !!!!!!

@KaytechGlobalSolutions 11 ай бұрын

Hey drew, Thank you for the video. Can i use this Aux setup for my wing too?

@sigil_theband1953 11 ай бұрын

Is it possible to do the FX AND all individual channels? It seems these tutorials are separated for some reason, but I have not heard you mention this. I'm new to all this, sorry for the ignorant question.

@jthunderbass1 Жыл бұрын

Do one on In-Phase.

@MateiVarlam 4 ай бұрын

Hello Drew! Thanks for all the interesting videos that you made. I've learned a lot from your channel. Is there a way to use H-Reverb on Wing with Waves Performer? I've tried using the external rack on a bus in order to use the reverb in waves, but the wing interface is not letting me select the appropriate sends. They remain on the N/A value.

@michaeltjin679 11 ай бұрын

hi drew, I have midas m32c and Behringer s32....I try your routing guide..but no luck...,,I do get signal through if I select card out aes 25-32 -into waves super rack...but on midas I can mute the effect nor adjust the fader on bus ....

@j-skyr2165 3 ай бұрын

Thanks for the explanation.. There is one question.. If we use this method, but we also want to use 2 channel of the USB out as the OBS input for live stream, then how would be the set up? Thanks.

@osiastedian 5 ай бұрын

Hi @Drew, Would it make more sense to route the delay to the reverb instead on the Console?

@kwameasamoah6930 5 ай бұрын

So with this superRack configuration taken up all the Auxs, How do we configure zoom, as zoom also takes Aux as well?

@hidewong 7 ай бұрын

Hi there , just wondering any recommendation laptop to run superrack performance? MacBook Pro with m2 max processor ?? Or Mac mini host ? Please advise and many thx for helping 😊

@checodosan4358 Жыл бұрын

Great video! Using this configuration plus inserting the mix bus on aux 5/6 is posible? I inserted the mix bus with SR performer on the M32 this weekend and I experiencing some phasing issues, is this normal ? My buffer was at 256.

@jacksonabang7077 Жыл бұрын

Hi Drew am very happy with your videos helping some of us who are FOH engineer in our churches, please i want to make a request from you. If you can make a video using logic or super rack performer on TF5 yamaha for live stream using Daw as my processor and the miser as my audio, or still we can scheduled a one one training I will appreciate and let me know. Thanks

@DrewBrashler Жыл бұрын

Yes you can. When you are using the mixbusses, you will need to make sure that you are not sending any original audio through the mixbusses and the main LR. For example if you are using the mixbus as a subgroup, you would want to un-assign the channels from the Main LR, and only have the channels going through the subgroup.

@DrewBrashler Жыл бұрын

@jacksonabang7077 I wish I had a TF5 at my studio to help make a video on this!

@francoisparent6478 11 ай бұрын

Theoretically you can do this using any DAW. It doesn’t have to be waves super rack correct?

@zomiht3300 Жыл бұрын

Hey drew, can I update my console from version 2 directly to version 4 without going from 2 to 3 then lastly version 4? I'm still skeptical that it'll not support the update as the firmware is the latest. Thanks!

@DrewBrashler Жыл бұрын

I would make sure to save and backup all of your settings. You can take a look at this video that has some tips: kzfaq.info/get/bejne/Z5xjh7qWy9CWpXk.html. Then make sure you test everything before you do your next show with it. I remember there was one firmware that Behringer added tap points to the maxtrix, and the newer firmware made it so they were all pre-fader. So just make sure to go through your settings and make sure everything looks right.

@awsb3640 7 ай бұрын

Qu24 Is possible? For Waves Super Rack Performer?

@edward5525 11 ай бұрын

Hi Drew my question is How to set Super Rack Performance in one computer and then record multi track and virtual sound check in another,

@ChrisCebelenski 8 ай бұрын

Not easily with USB connections - It's point to point. But take a look at DANTE where you can just route the audio to another machine. You're still going to have to work within the limits of the X32 however and unless your channel count is fairly low run out of capacity.

@wdrmusik7595 2 ай бұрын

How to use Superrack performer with a Flow8? Thanks

@benseghers6905 Ай бұрын

I like your videos but since im working with the M32C its very confusing. However I managed to make the reverb work with this video, thx! Almost all the guys expaining routing use the x32/m32 instead of using the edit software or Mixing Station😞It would be verry helpfull if you could make a video about routing using the edit software! Im still having problems to understand the logic behind the routing

@ALCOFRE Жыл бұрын

Is it possible to use the aux method AND the channel method simultaneously?

@DrewBrashler Жыл бұрын

Yes, you could set Card 1-8 for the aux method, and then Card 9-32 for the channel method. Another option is to use the User Routing and then have more detailed patching options. But the only downside is that the Auxes are only able to get 1-6 on patching i.e. User 1-6, Card 1-6. You wouldn't be able to set the auxes to be User 26-32. Hopefully this makes sense.

@wileec5939 11 ай бұрын

@@DrewBrashler Thanks for this answer - so far, in my research, it has seemed an either or proposition. I'm soon to get SuperRack Performer and have a very beefed up current MacBook Pro to dive into this - also tapping into the Waves support page and aiming to use plug-ins with zero latency to minimize the software/computer element, aware that there will still be some latency from the USB/hardware side of this with the X32.

@johanalbertobricenonino5130 Жыл бұрын

greetings friend how can I add plugin to mI L and R and how can I create sub groups from the superack thanks

@checodosan4358 Жыл бұрын

kzfaq.info/get/bejne/rLmnd5WT0LjScYU.html

@user-mq1kl7lm2c Жыл бұрын

👍👍👍

@DrewBrashler Жыл бұрын

Thanks!

@muhammadrafi4123 3 ай бұрын

Pls explain m32 how to use super rack

@rudygomez6996 Жыл бұрын

😅 i have a tascam model 16, is it similar process? Thank you!

@DrewBrashler Жыл бұрын

I have never used the Tascam Model 16, so I can't give specific instructions on how to do it. Sorry!

@rudygomez6996 Жыл бұрын

@@DrewBrashler its okay , thank you!

@morsikpl Жыл бұрын

Second time you're talking about inability to use TS AUX inputs, which is actually wrong ;) You can do some clever routing with User Inputs and reroute Physical Aux inputs into regular Channels (1-32). Obviously you'll lose Some channels, but it all depends on your use. And yes - I did this exactly for Waves purpose.

@DrewBrashler Жыл бұрын

You caught me again! I recorded this and the other video back to back. But yes you are correct, you can use the user routing to circumvent the issue of removing the aux inputs.

@grayancyagra5334 Жыл бұрын

Could you make the same video on Presonus Studiolive live III Mixer

@DrewBrashler Жыл бұрын

I would love to, but I don't own that mixer. Maybe in the future!

@pauetfpv Жыл бұрын

Hi, testing that I realized that the insert point is before the fader on the effects bus. So indeed, moving the fader of bus 13-16 dies not hace any effect on the sending of the signal. Is it like that, or am I missing someting and should work as a normal effects bus? Thanks for all

@DrewBrashler Жыл бұрын

You can set your mixbus sends to be pre or post fader on the console. If you select the mixbus, you can then press view in the config/preamp tab, and then change the sends configuration. You would want to have monitors/IEM's set to pre fader, and anything for effects set to Post-Fader. Hope this helps!

@lazerbsound Жыл бұрын

Hey drew, Once you insert the FX onto the bus as an insert why not just send it into the main LR channels and avoid another step by using the aux channels for this, just like you do on the Wing, I understand it might be for people that need the return for monitors but maybe show both ways so it's easier for most people, or for say FOH engineers who don't need the return separately. Love your videos btw keep up your gr8 work🙏🙏