You should pin that ! 👍

Burning graphite under water with a Tig welder creates a gas that when captured and compressed like air can be stored like propane. It bonds the oxygen and hydrogen molecules together with the carbon. The inventor who tried to bring it to market back in the 90's in Florida even tried to sell the idea to NASA according to the videos I have seen. It was called Aquafuel by this guy and claimed it was ZERO point energy when setup properly. The gas that was created with electric till it was enough to run the generator and compressor then ran the gasoline powered generator putting out enough AC power to run BOTH and still made enough gas to fill the propane tanks. I don't know where to find this on Internet anymore. However Larry Rise from Missouri Renewable Energy Channel use to sell the videos at his energy fair's. May be able to get one still if any are still available. It shows the whole process. Easily replicated if you are able to get one of these videos. I don't know what happened to the inverter and where or why it never made it to market Other than it was SO easily replicated. He drove a mustang on the gas. And claimed that the only thing that exited the exhaust pipe was water. A truly green gas. The only reason I can think of that why the government didn't allow it was there is no way to meter or tax the gas created. Because again it's so easily replicated and no way to monitor the use. Inverter even explained how to make the gas from sewage water and claimed that all that was removed from the process was turned into carbon and could have more graphite made from the waste. ????? DEFINITELY worth looking into if you guys were to be witty enough to tackle such a task. Show us ALL how easy it is done... Be the change...

It use to be on KZfaq

Y’all should so use the old truck with the two piece windshield and step side and put it on that frame that would be so cool to see

Porsche Unimog....... Overlander...... Webasto heat inside...LPG powered..... Yea, I just don't see a Porsche Unimog overlander on KZfaq anywhere........

I agree!

@@GrindHardPlumbingCo just make sure to slam that jag body real low on that frame! I trust your cutting skillz! :D

Hell yes! Jag by 4

@@GrindHardPlumbingCo Unleash the Jag-o-War!!

It's the mogster truck.

yes please

Agreed.

In other words make it a unimog? What’s unique about that…

@@DarcemanCRF300L well with the Grind Hard attention to detail it would come out looking amazing like their pickup they rebuilt and caged. And I counter what’s sooo amazing about a minivan or Jaguar body being on top? To me personally it’s cool for a minute but then my brain takes over and it’s just, meh. I’m more impressed by something more custom. Like Gingium’s adaptation of WRX driveline into a Miata. It wasn’t just empty the shell of the Miata and find a way to graft it onto a cut down WRX, he cut frame rails and built a tubular section to be able to mount the front subframe to. Just my 2 cents.

I though that as soon as I saw the combi sitting there.

Wider tires?

have you seen the original body!? The van is probably safer, but stlll dangerous

@@lancerutherford3933 You're right, its a toss up. Haha

Agreed 100%

Its been done, at least for the front axle, low gearing and they steer really tight too.

The vw bus was rear engined

@@sean6992 thought the unibog was rear engine ? Looked like it would of been easier as far as the pedal set up as well though,

Thanks man that really means a lot:) I just finished STI swapping it! -Will

Yes, it would be unstoppable until the wheel bearings and portal hub bearings gave up prematurely, and without power steering, which these unimog 404's never had, it would also be unsteerable at low speeds.

@@fintan9705 you can't add hydraulic assist steering? It doesn't need to be street able. They rebuild the axles on monster trucks every show and these guys have replaced the ball joints in their tacoma more times than they'd like to remember

@@16driver16 yes there's always hydro assist, but rebuilding those portal hubs ain't cheap, if you're doin regular rebuilds you're gonna need deep pockets, for bearings and seals alone you're talking the best part of 500 bucks a hub.

Are you going to be there

@@GrindHardPlumbingCo No, but I’d damn sure figure it out if you went!

You know your channel has made the big time on yt stats when you start getting the porn spammers. Next level up you get Madam Odwabae the love guru, and after that is "Elon Musk" "giving away" bitcoin for a small trade.

Yes sir 🙏

also def should throw bigger tires on it, and make it a real monster truck

It is. Ery cool!