Garage 54 NEVER dissapoints !!!! Nice contraption !!!!.

I'm not going to lie you can probably make 100 of them and sell out in a week

Legitimately looks like a fun ride. Some safety equipment and a dedicated place and I bet you could do pretty fast speed without feeling in danger.

Amazing. That Two Stroke is doing it's best 😂

You should put a T handle to hold onto and fix the controls to . That way you have something to hold onto and use upper body weight to help steer as well . I bit more power and I bet you could get that thing really flying and a bit safer .

Wow - G54 should build these and set up a new class of motor racing 👍👍 I'd love to see SkateCar racing.

Vlad mentioned personal protective equipment, which is good. Somebody else mentioned a "dead man switch", to shut it off and apply the brake if the rider falls off. I was thinking that too. The idea of a harness is an excellent one, and I wish I'd thought of it. The reason it wants to roll and turn on acceleration is the engine's crankshaft runs fore and aft. When the engine accelerates, it increases the torque on the crankshaft but it also increases the counter-torque on the crank case. That forces one side of the deck down, and the trucks translate that into a turn. If the crankshaft ran side to side, it wouldn't try to turn on acceleration. It would try to lift one end of the board, but that would not affect the turning behavior of the board. I am waiting with bated breath to see what Long Board v2.0 brings.

Tony Hawk's Pro sklada

This channel is great

Garage54 NEVER dissapoints!! This is your best contraption built ever

perhaps one of the BEST videos of Garage 54. Awesome not some shoddy stuff !!

This is so much nostalgia for me! I remember when I was like 15 or so, I bought this motorized longboard (2-Stroke too, back in the day) and I had so much fun with it! It was very unsafe, very fast and an absolute blast to drive! It fucked up my entire back at one point because me, being smart, thought that a t-shirt was perfectly adequate protection. 🤣 Thank you so much for making this!

This is "hands down" one of the coolest inventions I have ever seen (legit) as an amateur skateboarder. I think you should definitely patent this! For a little less board roll, you could try a spring resistance system like a mountain longboard 💯👍👏🙋

5:59 Shucks from a Lada 🤣 Even the captions say that. Your translations and voiceovers are still very impressive!

Two shocks on each axle would make the unit easier to control. It would slow the immediate reaction to positional changes. Excellent post, as usual.

!!! 🤣🤣🤣 I’ve been watching these guys for years you never know what they are gonna do next !!

Always better than almost all the American automotive youtube channels. The only one who does more interesting or crazy things is probably Whistlindiesel.

Absolutely amazing! Also, no need to do a voiceover, hearing it in Russian and with the music naturally, but with a subtitle option, would be way better.

Awesome fun. Great job guys. Ever thought about making something that fly's? Remember those toy tethered planes that took off and landed while attached to a pole/post. If you based it on a Lada it would need a lot of weight shedding and still need a lot of lift. Not sure if it's even possible but if anyone can, Vlad can.

It needs to start off level like a skateboard, and return to level after turning..a skateboard doesn't stay tilted.....I love it! Very cool!

This is why I love you guys.

Awesome! Best one yet! I think there could be an international market for these big skateboards; Races, obstacle courses, etc. Great one guys!

Just when I think I've seen it all...

Solid! Top KEK! Peace be with you.

Braille Skateboarders need to try this👍🏼

Now all they need is grip tape and fenders for safety

If you install a handlebar then you've turned it into a scooter and could call it that in the video. It also needs scuff pads to make your shoes less likely to slide. This is pure Garage 54 with the 2-stroke and cable grips, but I wouldn't be surprised if another channel made one with an electric motor and battery so that it's more powerful and quieter. I didn't think it would turn very well, but it's actually quite good. Kudos to the guys for figuring this one out as they went.

Some springs or bushings to help it return to center, and adjusting the ratio on the steering may help. For now it wants to fall into a turn and takes a lot of lean for a little turning.

have you guys ever tried dynamically balancing a car tire with beads or golf balls instead of lead weights? I've seen it done with trucks but not a car.

actually, if you lay down on it, with head forward, and drove it like a bobsleigh would probably be fun :)

10:42 "anyone wanna try this out?" "We're good."

very cool design!

"Shut up and take my money!!!" LOL seriously tho that looks fun af!

This is seriously incredible. Excellent work, guys. I want one.

I love this channel. Interesting experiments done well and with humour

That's just way too cool!!! Congrats!!!

You guys are just badass! You guys are hacks , but also precision at the same time! Nobody compares to 54Garage!

You guys should tour this to some places! People would get a big kick out of it!

That was awesome, and a lot of fun! Thank you!

Your are so totally mad I just love it.😂

The skateboard needs a certain suspension where it works stiffly when you balance in the center but once you lean to the left or right it automatically knows to move over

Very nice accomplishment, guys. It's really cool, and I've never seen anything like it before . Would like to see what y'all can accomplish with part two of this .

Springs to both push back on roll torque and to help self center it

Amazing build!!!!

Just... just.... wow! What a dangerous contraption of joy this is.

@9:00 area, I can see some snowboard bindings would help out staying mounted good and safely!

Those boys are so frickin clever - just look at the work in that, fantastic.

What a lovely way to get around the ‘NO SKATEBOARDING’ signs!🤪 Edit: what a great build! Go ahead and make more of this!🤪

Brilliant. You should be exporting these. And using it without a skid lid... hardcore.

Your imagination and ingenuity is always on display. Your team are amazing talents. Love the videos

you guys are crazy! i love it!

rig a steering rack to the frame with some sort of handle bar through the board that you pull left or right to tilt and attach brake / gas controls to . would also be something to hold on to . :) good work guys!

You guys should add wedges of wood to stand on, similar to how the edges of a skateboard are slightly taller than the center. It may make the "roll" more manageable.

This is An absolute new trend.. This tops at all you guys are gonna make money with this, You guys are gonna be building these for people❤❤❤

wow this is a well thought out idea and could be a sensation down the road. looks like it could be patented it is clean and well put together. just need to practice safety while riding it great job guys.

Great design, all you nead is safety cables front and back so you can focus on turning and brake as hard as you can, like have a harnes on you and cables holding you in place from rolling back and from tipping foreward, then you can upgrade that engine, the breaking force and really have some fun with that thing. Hope to see a part two on this, you will never fall off if you had cables.

Handles and grit-tape it's like sandpaper (keeps feet from slipping off the board) for skateboards, steps, pool areas, bathtubs, and other areas.

Ring around body type of handle and some long platforms on a sides to put a feet during turns 😊

I have an idea for the seat. That’s one hell of a sport. The seat lay back with a nice tube to support it. Futuristic stuff. And a front windows. To protect the front with bars guard

I love that guys...but maybe you should put a handlebar somewhere at the middle maybe from a bike, and put those controls on it, in that way you'll have better control and stability...😊😊

That turned out great. Now you need to patent it and sell them all over the world!

This is so beautiful - it made my day - you did an absolut great job!!! I like that you bring even crazy ideas to life! 🥰

I think Garage 54 just invented a new Olympic sport.

Great stuff, guys! One suggestion to make it easier to control is to use hydraulics to control the roll. The hydraulics can be controlled by two valves on some pedals you step on.

This is so badass. You guys have become damn good at quick fabrication work. I think you've created a monster with this one and a lot of channels will be popping up with their own designs in no time. Hell, I'd be tempted to make one if I had the time.

Use Spring/Damper combinations from a motorbike instead of the car dampers. Also increase the Tire pressure to reduce the drag.

Hydraulic (or cable wrapped around a tube using a steering wheel) tilt steering for better control. Mount maybe 4 passenger seats (+driver) and you'll have a skateboard taxi. And about 20 more HP.

I am definetly a bad welder, but jeeeesus... these videos make me look like a pro with 40 years of experience.

This is legit very practical if the steering becomes easier (wheel) and you add a seat with belt. Just those 2 changes should make it safe to go at much higher speeds and probably some weight reduction would help a lot too. Maybe some steel bumpers for good measure, a plate place and signaling to make it street legal and that'd make me and a bunch of people get one. Simply because it's easy to repair, minimalistic in what it has and very good for parking with the double axle steering. I hate bikes because they're with 2 wheels, but if a bike-like simple car exists with 4 wheels i want it.

if u put a Handel on the centre of that skateboard to mount the throttle and brake, it will become more easier and even more fun to ride. btw great work👍

This needs to be a competitive sport ASAP.

Good Ruski 👍 👍 ingenuity just like the mig

Handlebar like others have said. Could even use more bike parts for throttle / brake and the handlebars even. Or....you could go FULL NUTS and install throttle / brake pedals as pressure sensors on the floor of the contraption. One on each side. Make it a TRUE skateboard (you'd have to grippy up the surface though too like a skateboard).

That's a great design, but how about a wireless control for comfortability.❤❤

Harness as well, attached at 3 different anchor points with lanyards, left, right, and aft, with only enough slop to let you shift your weight. So you can't get thrown off and you can stop without being thrown forward

From America This is a cool shop I hope we can all get along ..We are very similar people should have metal bar in center to steer

Muad'Dib Muad'Dib! Muad'Dib! so awesome. dune irl. could make it motor actuated, so you can use 2 rods like in dune, to control the steering ;)

Seems very nice. Should have some torsion suspension. Maybe made of rubber. To keep it upright.

That was awesome build.. only thing i would add is foot stops.. on each side.. so you can't slide too far one way by accident or if it gets wet..

Looks pretty damn fun. To upgrade, cover the center standing area in anti-slip grip tape, upgrade he steel cables to wider ropes with a triangle-kinda handle at the end, mount each of them as far to their respective side as possible and you should have pretty stable riding stance for higher speeds.

have been blown away by the competence of your crew. Very skilled set of lads!

They need something like boot straps on skis to lock their feet into the board. It would make it much easier to control direction and also safer as well.

Definitely needs some spaced out foot locks like on snowboards. Wide enough and in the right stance and you can easily lean onto one foot to turn. Also, id love to see the turn radius vs a car!

Amazing. Handles, and tune the two stroke exhaust pipe - it's not getting in the power band.

nice drone skills

Using some type of a progressive shock, so the harder you try turning the more resistance there is a progressive setup might help fix the you are talking about.

Add the textured foot surface for better grip and control... stand in a different position to get better performance and reaction once the familiarity increases...

Make an electric version for more torque 👍 Also thinner wheels might help with weight and more movement. Also a kill switch to stop it from rolling forward if / when u fall off like those cables on a treadmill :D

I always enjoy garage 54 videos

A leaning post like on fishing boats will give lots of stability. And, it won't take away from the cool looks.

Very nice work. I was thinking you could add truck bed spray liner to add grip and it would look like grip tape.

Brilliant. And it looks so good. I'll bet these young fellas think they're the luckiest men alive. Just making fun things all day.

That looks so cool. I bet slow speeds feel fast trying that out.

Needs wheel arche covers or someone's gonna get noodled through the gaps around the rear wheels. Needs a padded post about waist high you can lean against when breaking. Beyond that, the contraption is perfect. I'd call this Super Moto Surfing.

All l can say l am super impressed this most insane motorised device you have ever made and how the motorised long board works

You guys are amazing Everytime I watch a new episode I am truly amazed

that's awesome!

Definitely the best video you guys made so far!!! Absolutely great 👍👍👍

That’s insane and I love it 😂

So you need a power steering pump. Make it hydraulic. Think out off the box. When tilt the steering will turn. Of the unit. More wight. But easy to turn . Front and back. Bigger motor. Or two stroke with boost. Mick Australia 🇦🇺. Ps put chain to the control so don't rip out. 🙏