WHAT A STEEL! - Rugged Ridge Venator Bumper w/ Overrider & 10,000lb Trekker Winch

Рет қаралды 47,021

2 жыл бұрын

In this video I will finally be replacing my OEM plastic bumper with a Rugged Ridge Venator Bumper w/ the Overrider. This bumper is full width multi piece stamped steel bumper with a inset winch tray. This bumper works on both the Jeep Wrangler JL and the Jeep Gladiator JT.
With this bumper I am also installing a Rugged Ridge Trekker 10,000lb Winch w/ synthetic rope and Factor55 Flat Link.
Below is a list of everything that was purchased and installed in the video.
RUGGED RIDGE VENATOR FRONT BUMPER W/ OVERRIDER : www.amazon.com/Rugged-Ridge-1...
RUGGED RIDGE TREKKER S10 10,000LB WINCH W/ SYNTHETIC ROPE - www.amazon.com/Rugged-Ridge-1...
FACTOR 55 FLAT LINK ($146.00): www.amazon.com/Factor-55-0005...
YZONA LICENSE PLATE MOUNT FOR HAWSE FAIRLEAD WINCH ($49.99) : www.amazon.com/dp/B09TR9PFFF?..."
Channel Information:
KZfaq - / @evolvedjeepin
Instagram - / evolvedjeepin

Пікірлер: 104

@WreckedBrewery

I really like this look and I'll keep in mind for when I'm ready to swap out my factory plastic bumper. Thanks for sharing!

@TimMcDonough Жыл бұрын

I have the exact same bumper. Love the look. Alignment during installation was also tricky. For everyone else who may get this bumper, keep things loose if you can until you need to tighten them, or no longer have access. The fog light surrounding are tricky for me, one is super tight, one is super loose.

@johnspurrier0001

If this were made in America, it would be the number 1 after market bumper by leaps and bounds.

@patrickbineau9546 Жыл бұрын

Nice job budy i like it

@nbookie

Clean look

@lonewulf0328

Funny that I only noticed now, when I was looking at your other video for the alpha spare tire carrier and the license plate relocate, that not only do we have the same rear bumper, but one of your other videos (this one) is the reason I first looked at the Rugged Ridge Venator. Only difference is that I went with the stubby variant. I guess fellow Canadians think alike, even I I havent lived in Ontario for 30+ years now. I miss it though. Florida is too hot during the summer 😆

@drmarkintexas-400 Жыл бұрын

🏆🏆🏆👍🇺🇲🙏.

@wo3518 Жыл бұрын

Please share if you come up with an option. Definitely replacing my front end bumper with the rugged Ridge Venator after watching your video. Thanks!

@VPhuoc79 Жыл бұрын

From what I've seen from other videos for installations of aftermarket bumpers from various manufacturers, I think the lower outer mounting hole on both frame rails need to be drilled out. As I understand, it is simply a "thing" when going from OEM to aftermarket, and it is only that lower outer hole; the other 3 are perfectly fine.

@88rushrocks

I like it I like it a lot lol

@patan77 Жыл бұрын

I've put the fav fours stubby and it's made for a tank but sunk my front end dramatically and the winch sits a bit high for my taste this looks great, just quality concerns... but seems well made.

@alexanderqwang5603 Жыл бұрын

Help me lot. Thank you.

@vjescote9239 Жыл бұрын

Do you have the OEM LED's? I have the stubby version and I had to modify the bracket to make it work. It's a great bumper! I powder coated my tow hooks rubicon red for a little pop of color.

@henryagallar Жыл бұрын

Thanks for the video. I'm deciding on a winch/ bumper combo and this bumper is on the short list. Are you still happy with both?

@marceld6061 Жыл бұрын

I have been considering this front bumper for a few months now. Do you think it would be possible/easier to attach the over-rider to that top piece

@Colebaby2324 Жыл бұрын

How did you get the inside part of the tow hooks wrapped? Were you able to get it seamless? “Seams” like that would be impossible. I’d like to do the same thing to mine