What I really think about the Festool LR32 system and more tales from the workshop! week53

Рет қаралды 1,331

5 ай бұрын

Machines
Paolini PS3200X Panel saw
Jet DC 1100CK Cyclone dust extraction
Jet AFS 1000 air filtration x 2
Sedgwick SM4 spindle moulder
Startrite SDX 310 thicknesser Planer
Record BS 250 bandsaw
Kreg DB 210 Foreman
Draper 38255 pillar drill
Tools
Festool TS55 tracksaw
Festool OF1400 router
Festool PS Trion jigsaw
Festool LR 32 kit
Festool Rotex 150
Festool ETC 150/3
Festool RTS 400
Festool Domino DF 500
Festool Domino DF 700
Festool Kapex 120
Festool CTM 36
Festool CTL 26
Festool MIDI
Festool 577257
Makita DTD152Z impact driver
Makita DHP482Z drill driver x 3
Makita DMR 116 Radio
Makita AF506 Finish nailer
Makita RT07 trim router
Makita DHR171Z SDS hammer drill
Makita DUC353Z chainsaw
Makita DSS611 circular Saw
Makita DTM50Z Multi tool
Paint room
Graco turbo force II HVLP 9.5 compressor
Graco edge controll plus II gun
Wagner finish controll 5500 XVLP
Custom drying racks
MAXVAC 3900M3/h extraction x2
FILMING/EDITING EQUIPMENT
I phone 10
Go pro hero 4 silver
VTGo112 dashcam
KDENLIVE PRO
Old Laptop my wife got from work.
PAINT SUPPLIER
renneritalia.com/
youtube.com/@rennercoatings68...
FIXINGS,SUNDRIES & CABINETRY FITTINGS
Hafeleuk.co.uk
youtube.com/@HafeleUKLimited?...
WALK IN SHOP OF CHOICE
Toolstation.com
youtube.com/@toolstationltd?s...
#carpentry #cabinetmaking #alcove #bespokejoinery #construction #building #workshop #joinery #spraypaint #oak #mdf #festool #carpentry #carpenter #construction #handmade #handmadekitchenset #bespokejoinery #scribe #cabinetmaking #joinery #workshop #buildingconstructionwork #buildingconstruction

Пікірлер: 13

@lincolnbrown1904 5 ай бұрын

I sold my Minipress and went with the LR32 set up, to save some space - no regrets so far. I got a 'set', but it was in between the two options you showed. Came with the plate, the parallel fences with stops, mandrel and the stops for the guide rail. No systainer, clamps or bits. I'll double check, but pretty sure you can still use the parallel fences with a rebated side panel, as the stops that register against your edge can slide up and down. I really like your method with the rail square👍

@Wattsjoinerybarn 5 ай бұрын

@lincolnbrown1904 yes I forgot about that option! Not too bad price wise either as the clamps are always handy! Do you know what you are probably right about the reference fence! It’s been a while since I have seen them. My money is a always on the block of timber tho😂. Here’s a thought! Why didn’t they make the plate symmetrical and the fence so that in clicks in the holes as well? That’s way it’s stop an edge reference ! I just feel like the least amount of bits you have out on your next the better especially when it’s so quick then you need to turn the rail. I am on the fence with the mini press! Thanks for watching

@michaelplays2449 5 ай бұрын

Beutiful work Matt !!!! Great video ,thank you

@Wattsjoinerybarn 5 ай бұрын

Thanks mate. Really got to sort out the filming/colour issues but getting there

@acollectionof 5 ай бұрын

Nice tip on the 25mm distance from edge to centre of the bit, I'll try to keep that in mind. I feel I have been getting the 'slop' issue on the holes as you mentioned when I've changed directions when plunging the holes. I do use the height guide and the front / back edge spacer guides as well. As you say I also very rarely make the same cabinet size twice between jobs so it's always a bit of a setup procedure. But it does work well for sure, until you forget to add an 18mm spacer (internal upright) like it did today and had to remake a whole panel 🤓

@Wattsjoinerybarn 5 ай бұрын

Yeah as I recorded the mentally overexposed🤦🏻‍♂️ video I realised that just putting a sticker on the board with an arrow on is the easiest way round avoiding the slop which can creep out and cause wobble. I have done what you did to today before and similar errors. A good system is to do all your holes then trim the middle uprights afterwards. Actually try this with most things as it makes the cut list less complicated initially! especially when I am putting solid wood lips on some panels. Really long winded cut list often just make me stair into space for hours😂 Cheers for tuning in.

@ShawwwHa 4 ай бұрын

You just saved me a lot of money. I was going to buy the entire LR32 kit. By the looks of it's unnecessary. Thanks

@Wattsjoinerybarn 4 ай бұрын

In my eyes yes! My kit actually fits in the of1400 router box too! If you buy it which I do recommend remember to always travel the router in the same direction. Key but info that! Thanks for watching 🙏

@ShawwwHa 4 ай бұрын

@@Wattsjoinerybarnthat is an excellent tip. I would be driven mad by wobbly shelves. I haven't seen a video on the LR32 explaining this occurrence. Tolerance buildup is a thing that doesn't get talked about.

@Wattsjoinerybarn 4 ай бұрын

Well said

@Dan-uh3ng 5 ай бұрын

How well does that sticks like s**t work on timber? Iv never thought of using it for that. Also what make is that edge bander?... Great work as always!

@Wattsjoinerybarn 5 ай бұрын

@Dan-uh3ng Hi Dan Tbh I have never had a problem with this, fix all or Stix all. However I do find that gripfill solvent free and the own brand solvent free grab adhesives are crap tho! Sometimes I do pva but not when on primed surfaces as it won’t hold. The edge bander is just a bench top hot air one from Scott and seargant. There are some Chinese knock off ones that are very similar too and tbh I imagine perform just aswell! For me it’s perfect but if I did wardrobes all the time I would get a hot glue one! If you get a system you can actually fly through the edge banding with this. if your local to Northants, Cambridgeshire area you could always come and give it a try! For the money I thinks it’s great! Thanks for watching

@Dan-uh3ng 5 ай бұрын

@@Wattsjoinerybarn Thanks for the detailed feedback! Unfortunately I’m quite far away but thanks for the offer! Keep up the great work!