Amazon Store: amzn.to/2Xfh2AN Our Merch Store: teespring.com/en-GB/stores/ca... Support the channel by becoming a Patreon and gain a whole load of benefits. / carsforpaul
Пікірлер: 31
@fasteddy9177 ай бұрын
I'd like to see it fitted out. Hello and thank you for another grand video, from White Rock, British Columbia, Canada.
@darenyeatman10077 ай бұрын
Yes I’d like to see the fit out👍👍
@PaulCareyDigitalWiz7 ай бұрын
Yes, please can we see the fit out 👍
@danpullin66107 ай бұрын
Yea, we would love to see this fit out , did a great job repairing the suspension components
@ched999uk7 ай бұрын
As a fellow windy it would be good to see the installation - especially the tank frame to chassis but it looks like that may already be done. There are always discussions on securing a tank properly, so it would be a great thing to see the frame fitting and the rest of the kit. Just have a look how many vids there are on actually fitting a tank frame, - very few that actually show the structural side of things. Great progress on getting the van back on the road.
@ianstoys13mgs7 ай бұрын
Yes, would like to see the fit out
@ryanfrench20007 ай бұрын
Be good to see the fit out of the van Paul 👊👍
@richardferguson86017 ай бұрын
Yes, I would like to see the fit out
@pitbullzz90467 ай бұрын
Yes definitely would love to see the fit out! 👍🏼
@funkyduckproductions.88447 ай бұрын
Absolutely. Show us the fit out.
@stevewood78847 ай бұрын
Yes Paul, I'd like to see the fit out 👍
@deckingking7 ай бұрын
Yeah, be good to see the fit out Paul 👌🏻
@TheSparkysdog7 ай бұрын
Yes it would be good to see the fit out. Nice job on the van Paul 👍
@minisareus7 ай бұрын
Yes please put fitout on you could use hot glue stick on pads for puller on arch
@andrewcapper23877 ай бұрын
Be good to see it fit out 😊
@a11csc7 ай бұрын
yes put the fit out in paul
@Pixleyjamaica1983UK7 ай бұрын
Paul nice job sure let’s see for out
@trevgilbert61467 ай бұрын
yes , would be something a bit different. now it looks a good useful work vehicle.
@sinorman2317 ай бұрын
yes to fit out something a bit different
@dieseldog2897 ай бұрын
Yeah I’d like to see the fit out matey. I’d also love to see you replace the rear corner tops on a transit van…… just an idea for content :) not that I have reversed into the local Asda car park!
@sleepysamk14007 ай бұрын
In for penny in for a pound. May as well see the fit out
@vr62807 ай бұрын
It would be good to see :)
@martinsheanon32327 ай бұрын
slightly strugling to install things like these rear trailing arm if you can find long cylinder head bolts depending on thread type great for alignment holding in place then jack unit up replace one bolt at a time with proper bolt ,,used this method supporting gearboxes in place by replacing two top bolts with long cylinder head bolts thus allows to give a big gap to remove clutch/flywheel etc without having to totally remove gearbox from under car long threaded rod will do same job just get thread type correct support engine as the long bolts would put more stain on engine mounts but you already should be supporting it taught this 40yrs ago but never seen anyone use this method but me its saves lot of time try it it was alway great on the old vauxhall boxes
@pommieforever7 ай бұрын
why not, go for it
@Lexusman657 ай бұрын
Hi Paul could you do a report on how the ID is getting on now that its been in use for a while.
@genty19607 ай бұрын
Please show the fit out 👍🏻
@st200ol7 ай бұрын
It’s like deja vu you already did a van like this with window cleaning stuff installed, including showing the installation what happened to the last van?
@robertbeattie90006 ай бұрын
I see that wheel is bent when you spin wheel before jack van down.
@thindo7 ай бұрын
Better than seeing yourself struggle is seeing someone else struggling with fitting something 😂😂😂Could we get an update on both the Tesla and ID3 cheers
@jbbumpkin7 ай бұрын
I cannot believe that Fiat are still using the same wheel location pin/bolt as they were when I was an apprentice back in 1973! Horrible things they are too because they round the corners off so easily!