Yes the NW works just fine with DW cartridge. The DW just has a fancy touchscreen and can print on 2 sides. (not really needed for transfer printing)

I use the Forever laser dark in almost every video I've made. I also bring Forever laser dark with me to trade shows and demos for Ghost. I switch between that and the UniNet Premium paper for pretty much everything.

It really depends on what type of paper you are using. I have not had time to make a video on the Versa Sheen hard surface paper that just came out a few months ago, but it works great with Ghost and also leaves a nice gloss finish over the mug. It is now my favorite hard surface paper to use with laser transfer.

When you are using laser toner transfer paper for hard surfaces we are just baking the toner on the top of the mug. If you are using the Paropy Hard surface you can put the mug in the oven for a bit at 400°f to bake it and increase the durability. My Nazzcar mug I didn't use the VLR on from the other hard surface video earlier this year is still going strong at 9 months later and 30+ washes.

Thank you for the reply

You can contour cut with every version of Vinylmaster

Multi Trans is a very waxy paper. If you are looking to do hard surface transfers with the Ghost toner you are going to need a paper that won't curl as much and isn't covered in a waxy release liner that will jam your printer. Versa-Sheen or Paropy Hard surface. Versa-sheen is my new #1 for toner hard surface transfers.

I have the M452DW and just got the M254 in for testing. So far so good!

Josh's Corner what white toner is compatible with the m254 model?

Greg Witte which brand white toner is compatible with the m254 model?

ghost white toner.com sells sublime for sublimation for this printer

In these videos I used Paropy Hard Surface paper and then for the clothing I used Forever Laser Dark

Which white toner I must buy for the hp254 printer that you shown on this video? TIA

You are just melting the toner onto the face of the mug so it won't have the same durability as sublimation. VersaSheen hard surface papers will give you the longest lasting results on ceramics and metals because the release liner acts as a protective coating that increases the durability of the transfer.

FOREVER MULTI TRANS PAPER*

@@kieranrmartin That is great to hear! What type of printer are you using? I can get a single pass design through without issue, my trouble comes when I have to run the FMT through for the second time on a CMYK and WH image when using the M452DW, 452DN, CP5225, and M254DW. The waxy film of the paper combined with the curling from the first run through made it impossible for me to get a transfer through more than a 3rd of the way through before it would jam. I was able to find a work around taping it to a sheet of construction paper to hold it flat, but I was still having jams. I do still have to use this method with the Paropy Hard surface for CMYK & WH images with ghost, but in my experience it has a much higher success rate with these cheap printers than the FMT.

Also, thank you very much for watching my video and sharing your knowledge with me. I do appreciate it very much!

We have a Sawgrass 400 and a cricut right now. Wanting to do more and less work as far as weeding.

@@deirdreholcombe8738 I'm looking into Flex Soft No Cut, I don't want to weed out 100 shirts myself. Check them out

Nappily Rooted thank you! I’ll check it out! ❤️

The Ghost white toner system is the most cost-effective, but has a steeper learning curve because you have to work around the limitations of the two-pass print for CMYK&WH and no product specific software. I tell everyone who is looking to purchase something for their business to look at the UniNet iColor printers if they are going to get something for their business. That is a machine that has been designed from the ground up to print white toner and comes with software and everything needed to make it easier to start profiting with.

@@deirdreholcombe8738 Flex soft is pretty nice. You can use that with a monochrome laser printer and make some very nice designs.

Can you print up A3 or A4?

The picture can be high resolution and still be blurry or pixelated if it wasn't resized correctly. You may want to start requesting a specific file type like a vector image or something that will allow you to resize the image with ease.

www.uscutter.com/VinylMaster

forever multi trans paper works good for Glass, Ceramic, porcelain items as well as wood. forever laser dark will work on wood as well but not as good as the multi trans paper

If you are using the Ghost printers you will want to use the Paropy Hard surface paper. The Forever Multi-Trans is also great, but it is too waxy and will jam up inside the cheap HP printers.

Just order it from Ghost directly. They are located in Germany

@@JoshsCorner Thank you!!!

The 454dw does not currently have a chip that can be used for toner cartridges. HP is keeping that tech under lock and key so they can make as much money as possible in toner sales.

@@JoshsCorner thank you 🙏🏼 I’m actually also looking to get the 254dw

Very insightful!

This is the first US Cutter Video I have watched on the White Toner. I gave up 1/4 way through due to the music and not being able to understand what is being said... The music is competing with the Ringing in my ears... Too bad... I bought my Vinyl Cutter from US Cutter many years ago and I am shopping for white toner... Bummer... Can the music... That is my 2 cents. Honestly you have lost a sale letting the kids add electronic music.

This is my personal KZfaq channel so you are going to see me progress and learn when you go back and look at my early videos. They are pretty rough and I can't watch them without cringing and totally agree with you on all these things. The USCutter KZfaq account can be found here - kzfaq.info