Why Seeed Studio's 24 GHz mmWave Sensor is a Game-Changer

Рет қаралды 1,960

6 ай бұрын

Seed Studio's 24 GHz mmWave Sensor is a game-changer!
In this video, we'll show you how this sensor can be used in conjunction with Seeed Studio's home assistant platform to create smart home applications that are beyond what currently exists.
If you're interested in smart home technology, then be sure to watch this video! By the end, you'll know all about the incredible capabilities of Seed Studio's 24 GHz mmWave sensor and how it can be used to create smart home applications that are beyond what currently exists!
Are you looking for a powerful and versatile sensor that can detect motion, speed, distance, and angle? If so, you might be interested in the Seeed Studio 24 GHz mmWave Sensor. This sensor is based on the TI IWR6843 chipset, which is a single-chip solution for mmWave radar applications. In this video, I’ll give you my initial impression of this sensor and show you how to set it up and use it with an Arduino board. You’ll see how this sensor can be used for various projects, such as gesture recognition, obstacle detection, speed measurement, and more. You’ll also learn about the advantages and limitations of this sensor, and some tips for getting the best performance out of it. If you’re curious about the Seeed Studio 24 GHz mmWave Sensor, then don’t miss this video!

Пікірлер: 15

@LNprod12 4 ай бұрын

hii! im honestly a big noob at this and no idea what im doing , but is there a way to connect this to Home Assistant using an esp32? It would help alot if you could make a tutorial on that, thank you :)

@benerdorg 4 ай бұрын

Sure

@awdhootkanawade Ай бұрын

Seed studio launched this one keeping home assistant in mind Attach this one to esp32 Upload esphome code and you will get this sensor in home assistant

@deepandwide2681 3 ай бұрын

Hi, Im only getting standard hexcode from the rasberry pi/mmwave sensor. Is there someway to get raw data? and also if this was put on a wall. Is there a way to find out (a) how far the person is from the sensor and (b) where the person is in the room?

@benerdorg 3 ай бұрын

As of now I have tested only on the Arduino library. And I think seeed don't have the library to use it on the RPI. May I know how you are getting the hex code.

@CryptonianWar 4 ай бұрын

How is this sensor made ? IR in combinartion with IMU?

@benerdorg 3 ай бұрын

Not an IMU, It's a mmWave Radar Sensor.

@realaniketsingh 2 ай бұрын

Hello Sir, I want to interface 24 GHz mmWave Human Static Presence Sensor with Arduino Mega using UART. This sensor provide library for Arduino. in this library examples are there like Physical parameter example, human state data decoding, fall state decoding. If I use one of them I'm not getting anything. please help me sir

@benerdorg 2 ай бұрын

Hi, please check your connections like tx and rx portions

@ilayarajaramasamy1263 3 ай бұрын

Can u provide Iput , output, gnd connection terminal information

@benerdorg 3 ай бұрын

Power > 5V, GND > GND, TX > D7, RX > D6.

@ilayarajaramasamy1263 3 ай бұрын

@@benerdorg thanks for the reply. One more doubt. TX and RX both are output? What is TX and RX for?

@benerdorg 3 ай бұрын

Tx is for transmitting information and Rx is for receiving information

@ilayarajaramasamy1263 3 ай бұрын

@@benerdorg bro when the sensor detects human, I want the sensor to send output signal to a relay, which controls power supply to a bulb. For this, only TX connection with relay is enough or RX also to be connected with something?

@benerdorg 2 ай бұрын

No, you need both rx and tx. Because controller will send some commands based on that command only your sensor will work. So, you need both lines.