Why Your Fuel Gauge LIES To You! Toyota Hilux Repair.

Рет қаралды 7,683

Жыл бұрын

Here I show you why when your tank is empty your gas gauge still says half full! This one is from a 2014 Toyota Hilux.
Tools I use -
Soldering
Quick 861DW hot air station
Duratech TS-1640 solder iron
Multimeter
RMM760D - can be found under many name badges
Microscope
Luzky Zoom 3.5 - 90x simul-focus single boom stand trinocular stereo microscope
Camera - Lucky Zoom HD 14MP
Oscilloscopes
Siglent SDS 1102CML 100MHz 2CH
Philips PM 3305 35MHz 2CH
Bench supply
Powertech MP-3086 0-30V 3A
TL866II PLUS universal EEPROM programmer

Пікірлер: 31

@DapperDavo 16 күн бұрын

Thanks Jonny and thank everyone for your comments. I have the same issue with my 2013 Hilux.... Will give this a bash this week...

@robertkirwan2389 11 ай бұрын

Excellent informative video. This fix works perfectly. Well done and thanks for sharing your knowledge.

@randyh5465 Жыл бұрын

Awesome post on how to repair faulty fuel gauge. I did this procedure on my 2014 Hilux and it worked perfectly. So thank you so much for the post. Saved me $$$ from purchasing a new instrument cluster. I live in Costa Rica and Toyota parts are very expensive if you can even get it.

@JonnyFix Жыл бұрын

That's great. I bet there's a good market for a repair shop there!

@el_Tsiapo Жыл бұрын

At the best case scenario, your video saves $100 on labor fees. At the worst, I dont know the cost of a new cluster plus labour which would do the same exact problem at around 100k miles. Especially in hot countries logically would come up faster. Blessed you!!! and Thank You!!!!

@eddevmsl3098 Жыл бұрын

Thank you it work well for me even after the Toyota dealership workshop could not fix it. They recommended replacing the entire cluster Board. Its a pity. Anywhere J thankyou for the huge savings.

@JonnyFix Жыл бұрын

Good stuff! Dealerships will never be willing to invest in a setup to repair stuff at this level. Plenty of companies out there making good coin on it though.

@sajidmohammad3190 6 ай бұрын

Well these stepper motors are smart enough to re-adjust their starting point. What I usually do is, place the needles facing upwards and turn them to zero (C and E for the temp and fuel). Make sure you turn them at the direction they move. Turning in reverse direction will mess up everything.

@hamiltontitinho1860 5 ай бұрын

thats work, i do this to my is working perfectly

@watup. 8 ай бұрын

thank you💲

@jasonmorris6770 Жыл бұрын

Great video this. I will look into this on the weekend for my hilux. Johnny what fluid did you use to clean up the board at the end

@JonnyFix Жыл бұрын

Isopropyl alcohol

@user-lf8dq2bf6r Жыл бұрын

Great video. Is there a way of testing with a multimeter prior to soldering?

@JonnyFix Жыл бұрын

You may be able to test between the pad on one side to the pad on the other, if the joint is high resistance it will add on to the resistors value. I think some are 220ohm so if you measured it at say 4.2k ohm you'd know the joint was bad. Note some of these are connected in parallel so be aware of what your expected total resistance should be before measuring (eg t = 1/(1/220+1/220+1/220) and be careful probing the pad that you don't touch or mush solder into the resistor and make it good again, probe elsewhere on the pcb that leads to same connection.

@zx8401ztv Жыл бұрын

Well done, the cluster lives again!. I can't imagine how much a new one would have been, not cheap i expect. As you showed the crack-idge i wondered if we can blame lead free solder for the failures. I'm no lover of lead free crap, can you tell lol. jeffescortlx is a pro at ill clusters, always interesting to see what died lol.

@JonnyFix Жыл бұрын

I blame lead free as well. Can you believe some places charge almost $400 for this basic repair! I really should take this up full time.

@zx8401ztv Жыл бұрын

@@JonnyFix If you do that, you will need spares and an exercising control to make sure its working ok. Go and watch jeffescortlx, he is a nice bloke 😀 He doesnt mind giving information away to help people. And if you already watch him, watch him harder.. oow that sounds odd 😀 Ok ill leave you in pieces lol.

@JonnyFix Жыл бұрын

@@zx8401ztv I don't need to watch anything harder, I get enough migraines 😵‍💫

@rikvanmoll 3 ай бұрын

Absolutely great video! I need to repair mine as well. Wondering what type of solder you used : lead-free or leaded?

@JonnyFix 3 ай бұрын

Leaded, always 😄

@rikvanmoll 3 ай бұрын

@@JonnyFix thanks! I was just checking as I am not an expert here on solder and read somewhere that both types would not go together well, e.g. reparing soldered joints with the opposite type of solder than the original. Again: great video that helps a lot of ‘gauge problem victims’. Keep going👍👍

@JonnyFix 3 ай бұрын

@@rikvanmoll All good mate. Never had a problem mixing them. You're only adding lead to unleaded to make semi-leaded haha. If you want to be really sure you can use wick to remove the old stuff first.