WideBeam House Boat SandBlasting stripping it back to Steel!

Рет қаралды 3,843

Ай бұрын

Ready to give your boat a fresh new look? Before diving into that repaint project, proper surface preparation is key, and sandblasting is the ultimate solution! Join me as I demonstrate the art of sandblasting for boat surface restoration. Say goodbye to stubborn layers of old paint, rust, and corrosion as I blast them away, leaving behind a clean canvas ready for a flawless repaint. Don't let your boat's surface condition weigh you down - embark on this transformative journey with me and watch as this vessel undergoes a stunning makeover. Get ready to set sail in style with a beautifully repainted boat that turns heads wherever it goes!

Пікірлер: 44

@philglover2973 Ай бұрын

Awesome video thanks Mick very much appreciated all the lads here love your work too 🇬🇧🚛🚛🚛🚛🚛🇺🇲🇺🇲🇺🇲🇺🇲

@Mobileblaster Ай бұрын

Excellent 😊 thanks for your support 👌👍

@scottkenzig5144 Ай бұрын

Nice job Mick 👏 👍. Always a blessing when It flies off nice and smooth 😎 👌 🇭🇲🏴󠁧󠁢󠁥󠁮󠁧󠁿

@Mobileblaster Ай бұрын

Thanks mate yeah I'm glad it did fly off I didn't have much room and the floor was wet 😂👌👍

@scottkenzig5144 Ай бұрын

@@Mobileblaster not the nicest conditions either 😕 👍👌

@Hyratel Ай бұрын

Mick, you seem to have non stop problems with the trigger electrics. A tip: use the smallest crimp ends that'll fit over the wire (they're color coded for size), it makes a sturdier connection and the plastic boot fits tighter over the insulation toreduce fatigue on the wires. Can also add heat-shrink over it to keep it from bending where it goes in, it should make your fixes last a lot longer

@Mobileblaster Ай бұрын

It's mainly because I'm a cheap Yorkshiremen and don't want to spend money on the so called proper stuff 😂 I've bought and fitted some ip68 inline plugs hopefully these will be OK the cable could do with a string down the middle to stop it snapping the cable when it gets snagged I got to admit its a very harsh environment and I work my stuff hard 😬

@25vrd48 Ай бұрын

Tight spaces . Great blasting job Mick .

@Mobileblaster Ай бұрын

😊👌👍

@charleswelch249 Ай бұрын

That's almost impossible to get much tighter and expect someone to be able to work on that boat. You made it look like new again and it's going to be really nice when painted now. Another hard day in the books.

@Mobileblaster Ай бұрын

😊 it was limited room but I somehow managed 😊👌👍

@hermantosihombing5837 Ай бұрын

Berapa kah perjam disana perkerjaan ini

@randydobson1863 Ай бұрын

Hi Mick & it's is Randy and i like yours cool & Thanks Mick & Friends Randy

@Mobileblaster Ай бұрын

Thank you for your support 😊👌👍

@art1muz13 Ай бұрын

thans for the share! U do great work, compa!

@Mobileblaster Ай бұрын

Thank you 😊👌👍

@christinekesler8964 Ай бұрын

This was a cool boat but I think I like the construction/heavy equipment more. You just seem so squashed when you're working on the boats. Plus it seems like the construction equipment has more rust and I like watching that get stripped off. Very satisfying. Really love all of your work 💜💜💜 Cheers from Michigan, USA

@Mobileblaster Ай бұрын

😊 I hope the footage for the job I've just completed turns out nice I've got a little treat I don't have many videos like that 😊 hopefully the dust wasn't too much and the footage is clear 😬

@christinekesler8964 Ай бұрын

@@Mobileblaster I'm sure it's going to be great! Looking forward to seeing it!😊

@Mobileblaster Ай бұрын

@@christinekesler8964 😊👌👍

@stephenthatcher6883 Ай бұрын

Mega job mate

@Mobileblaster Ай бұрын

Thankyou 😊 👌 👍

@phillipsharpe6459 Ай бұрын

Another brilliant video pal, i bet it took some time to do, 😁👍

@Mobileblaster Ай бұрын

Yeah I put a decent shift in to get this done in the day 😬👌👍

@chriseccles1454 Ай бұрын

🎉🎉 Good job you're not a big chap in tight spaces. Do you ever blast the props off the boat or would it affect it's balance.😊

@Mobileblaster Ай бұрын

Thank you Nah it wouldn't affect the shaft but I've never been asked to blast 1 😏

@CompuWhizz Ай бұрын

Good un!

@Mobileblaster Ай бұрын

😊👌👍

@joeroad6618 Ай бұрын

Never seen where they bolt on the anodes before, usually they are welded

@Mobileblaster Ай бұрын

Yeah I court my back on them and was thinking why why would they put them on haha

@rossnolan2883 Ай бұрын

Epic 😊😊😊😊😊😊

@Mobileblaster Ай бұрын

😊👌👍

@WombleUK Ай бұрын

Ah mate, I know we always ask why do they not bother doing the underside of the barges but that's not a pleasant job crawling about underneath to do them. I bet you're glad they don't all have the underside blasted LOL Do you charge the same or more to do the underside?

@Mobileblaster Ай бұрын

Yeah its not very nice crawling around under boats. As ya can imagine each job is different so they very slightly 👌👍

@jimsvideos7201 Ай бұрын

Does sanding ever work for these? It seems a lot of people try it and then call you.

@Mobileblaster Ай бұрын

😂 it must do but it's false economy for a poor finish when they know blasting is perfect for repaint 👌👍

@tibrov866 Ай бұрын

It’s look great. How long time it takes to blast that boat? 😀

@Mobileblaster Ай бұрын

I didn't count but it was done in the shift 👌👍

@olivermarsh5077 Ай бұрын

What media wold you tend to use on cast iron and sheet metal to leave a nice paintable finish

@Mobileblaster Ай бұрын

That would depend on what needs removing?

@francisarmstrong6463 Ай бұрын

Get yourself a 4 legged stool Mick . You can always saw legs off to suit your height .Save you stooping.

@Mobileblaster Ай бұрын

I move about too much to be seated. What's don't come across on camera is my arms burn as its kick back presure is around 15/18kgs imagine holding ya arms up and then something pushing them sideways that's why I look random as I go along in uncomfortable places. A got a nailing mat but the floor was wet though I just couldn't win 😂

@francisarmstrong6463 Ай бұрын

I Mick, again or just make one out of some old off cuts 3>3 or 4>2 .

@Mobileblaster Ай бұрын

Make what sorry?