Wii Remote Teardown and Analysis

Рет қаралды 66,925

Andrew Montgomery

7 жыл бұрын

ENME473/690 Wii Remote Teardown and Analysis submission

Пікірлер: 52

@bensosnowski1128 3 жыл бұрын

For people trying to open their remote: 1:25 the editor circled the wrong part. The plastic piece shown on the left is a cylinder extending from the top piece of the remote. It’s used to stop everything from moving when the remote is closed, as it hugs a contour on the motherboard and bottom piece. The plastic piece on the right is a tab that extends from the bottom piece and holds the motherboard to the bottom piece. It does not touch the top piece of the remote. To the right of the red circle, you can just barely see the actual tab. (Shown at 1:31) The female part extends from the bottom piece with the contour facing the outside of the remote. The male part is on the top of the remote and is not visible. The male part is very small and is very likely to break when opening. At 1:34.5 you can see they actually broke both the male tabs off the top piece of the controller (Slow to 0.25x speed to see the in-focus frame). Don’t feel bad tho, it’s very likely to happen to you too.

@DaDASHDevil 3 жыл бұрын

Great information, thanks!! I’m trying to open a Wii-mote right now...

@joaovictormansano 2 жыл бұрын

Hi do you know the size of the tri wing screw driver?

@stkutu 2 жыл бұрын

2 of my remotes plastic pieces are broken even I read your comment. It is really hard to open remote without break them as you said(at least for me). I will tape both side of remote. Thanks for information

@fishingkh60 2 жыл бұрын

@@joaovictormansano I use the Y2.3 tri-wing screwdriver. But, the next size up or down should work fine too.

@josephbill937 5 жыл бұрын

This looks like a school project so they probably won’t answer your questions

@howardye8569 4 жыл бұрын

Joseph Bill to

@leopoldogonzalez5444 3 жыл бұрын

loooooooooooooool

@joestyles4639 6 жыл бұрын

This is brilliant! So much detailed information :D

@bucanier 3 жыл бұрын

What an incredible analysis !! Congrats

@KlingonCaptain 7 жыл бұрын

Wow, you guys put a lot of work into this.

@TheFrenchy82 6 жыл бұрын

Nice analyse ! thanks !

@markuzi6755 5 жыл бұрын

There is a big problem with your analysis. The BU8849FV is not a flash memory. It is a 24pin ADPCM decoder with an 11 bit digital to analogue audio output and contains an audio amplifier. The 16pin BU8844FV version of this chip used in other wii remotes did not have an inbuilt amplifier and it needed a separate audio amplifier support chip..

@dylboy69420 4 жыл бұрын

I don't think they care

@RoddyDev 4 жыл бұрын

Yeah, you're right. There's no need to have 16kb of flash memory if there's already 128kb for storing all the microcontroller codes. Also notice that they didn't mention any audio decoder chip at all in the video.

@PTEC Жыл бұрын

😞

@trevrr 4 жыл бұрын

I'm just here to see the disassembly so I don't fuck up my Wiimote while I'm trying to clean the shell

@punishedhaidar 3 ай бұрын

What a great video!!!

@dolko1944 6 жыл бұрын

Nice video! My internal speaker is starting to crack down. Can i replace it? What type of replacement speaker do i need? Or its just a cable fault?

@bulk4268 3 жыл бұрын

By the way: the clips aren't in the position the red circle shows. They are at the height of the up-button. Using a tool to push the upper shell gently outwards at this area will prevent them from breaking.

@AaronKNH 2 жыл бұрын

Wow... Great 👍, that all i need to service my wii remote. Thanks 😊.

@imionnazwiskon9786 3 жыл бұрын

Yep, its wooood.

@Ty-uy8rb 4 жыл бұрын

Hey! i am just wondering if i could use a screenshot of that broken down wii remote for a website I'm making, i can credit you if needed :D.

@danielsaturnino5715 3 жыл бұрын

Great video. I wish you have identified the small chip next to the negative battery tab. Mine got corroded to hell from battery leakage. Thanks

@ancilduncan4150 3 жыл бұрын

Smh... the Rabbids got you too, they pissed all over my PCB

@cavjjunior 2 жыл бұрын

After a few minutes the remote dies if I remove batteries and wait some minutes, it will turn on again when I put batteries and will die soon again. Not a battery problem. I'm going to try and replace the main capacitor, that huge one near the bottom. Am I nuts?

@PTEC Жыл бұрын

@bryceshaw06 8 ай бұрын

Did replacing it help?

@cavjjunior 8 ай бұрын

@@bryceshaw06i was not able to perform the replacing and ruined the board. Since that time i got a little better at electronics but not much. I'm not a pro, but this video is still a lifesaver.

@juanpsy 7 жыл бұрын

I want to know how much pcb i can trim to let the Bluetooth chip & nunchuk port usefull

@juanpsy 5 жыл бұрын

Hi, I hope that you answer our questions. :)

@gocarlos987 4 жыл бұрын

Parabéns até temperatura foi mostrada no vídeo

@jeffbrito8604 4 жыл бұрын

Pensei que era só eu de br kkkkkk Mas esse video me ajudou a conhecer meu wii remote

@gocarlos987 4 жыл бұрын

@@jeffbrito8604 pois é eu estava procurando tutorial para consertar meu controle do Wii , e vc curte Wii?

@valterlqsantos 4 жыл бұрын

@@gocarlos987 o q uma quarentena nao faz....ahahaha geral desmontando o wii

@elcapitan7 6 жыл бұрын

hey can you help me? I have a chuck that is having issues with the motion. I have to smack it to get it to work even then it won't stay working properly. I bought a cheap chuck and the motion controls are fine but the stick is stiff and I don't like how the c button feels. I this the broken chuck is just getting "jammed" or stuck if you wanna call it that. I looked up how the motion control works and that its type of gyro so I figured maybe the gyro in the chuck was getting stuck which is why smacking it work by maybe knocking the gyro loose and back into normal position. anyways is there a way to fix this? I just don't want to spent money on something I think I could just fix. I already thought about swapping out the buttons but I still have the problem with the stick being kinda stiff. please and thanks for the help

@noxious_nights 4 жыл бұрын

it's called a nunchuck or nunchuk.

@chainedwings4035 4 жыл бұрын

@@noxious_nights This dude has asked for help and you CORRECT THEIR SPELLING???

@noxious_nights 4 жыл бұрын

Dude chill the fuck out, I'm just telling them what it's called

@bensosnowski1128 3 жыл бұрын

Just open it up so you can figure out what is actually wrong. Look up “GameCube joystick replacement”. That should show you how to fix it, and what the problem is (worn stick or faulty connecting part)

@unoyoshiblu700 2 жыл бұрын

What are the dimensions of the rumble motor? I am searching for a replacement one to keep the original remote and fix rumble. (my remote does not vibrate, i checked the home menu too😑)

@pb200sxgmail8 3 жыл бұрын

My WII remote just vibrates when I put batteries in it. Any ideas?

@garfieldnate 2 жыл бұрын

What is the purpose of covering the capacitor in a rubber sleeve?

@PTEC Жыл бұрын

idk

@jordanhendricks7396 Жыл бұрын

Likely insulation for emf

@jonaslasater4784 4 жыл бұрын

w0w

@realfunfunkers8852 Жыл бұрын

Hey my wii remote battery die so fast any suggestions?

@Kifka-a 5 ай бұрын

Can you please repeat this video with a wii remote with motion plus integrated? i think i have a faulty resistor/capacitor i dont know, its small and has the letter G on it or at least its looks like it. next to it is the letter F11 its between the 1 and 2 buttons

@Kadano 4 ай бұрын

You are probably referring to F1, which is the primary fuse. If it doesn't have continuity, you'll have to replace it with a new fuse. If you don't mind the risk of more vital parts getting potentially damaged, you could also just bridge it with a tiny wire. Before you replace or bridge the fuse, you should check for liquid damage / trace rot.