Wildax Pulsar, What’s New 2021

No video

Wildax Pulsar, What’s New 2021

Рет қаралды 1,365

2 жыл бұрын

#Wildax Pulsar
#Wildax
#Pulsar
#pulsar2021
#whatsnew
#Just a swivel table
#swivel table
This is a short video showing how w fitted our little swivel table in place of the factory fit tables. The factory fit tables are in a set position in the middle of the isle and are in the way to past when you have cooked a meal.
The table and leg system was purchased off eBay, see links below
www.ebay.co.uk...
www.ebay.co.uk...
You buy at two different suppliers, one for the leg and one for the table. These have made such a big difference for us on a Dailey basis. We highly recommend thee for anyone with a Wildax Pulsar.
Don’t forget when you take out the table support at the bottom, you will need to cover up with carpet or carpet tiles, as it leaves small holes and holes are in the carpets supplied
Watch our other video. • Wildax Pulsar, What’s ...
Thank you for watching our channel.

Пікірлер: 22

@josh_bfc_2769 2 жыл бұрын

Brilliant idea. Very useful table. Wildax should fit them as standard 👍

@jimandkay 2 жыл бұрын

@michaelhartley11 2 жыл бұрын

got 1 with 2 plates so i can have at the front and/or back, mine is a Lagun table

@jimandkay 2 жыл бұрын

Brilliant 😀👍

@markwood6324 2 жыл бұрын

Thanks Jim for showing the set up of the swivel table Hoping I can do the same metal plate inside the seat set up Looks like one the long nuts will have to be cut shorter to clear the truma boiler Ordered mine last week after you commented on my last question I asked Did get it from your eBay link thanks again Don’t pick up my pulsar till next month so will be ready to do the table amendments Did you mark out the table top position before securing to the table ? Regards Mark

@jimandkay 2 жыл бұрын

High Mark, again thanks for watching our channel. Not long now before you get yours, you will love it. Yes it is a good idea to mark out first and just put 2 screws in, then you can test the position that suits you. Best of luck, great to hear from you again. 😉👍

@markwood6324 2 жыл бұрын

@@jimandkay thanks for your reply Jim I will do the tip you suggested for table top Meant to say looking forward to your France 🇫🇷 trip this year Will be watching closely as it something we want to do at a later date never been abroad in a van so far newbie’s for last 2 years Regards Mark

@stevenlocke8743 2 жыл бұрын

Hi Jim another great video wot is the measurements of the main bracket bolted to the seat from the plastic vent and how high is it from the floor thanks again for a very informative video

@jimandkay 2 жыл бұрын

Hi Steven, I can’t get to it for a few days

@stevenlocke8743 2 жыл бұрын

@@jimandkay that’s ok Jim whenever you can much appreciated 👍

@55glencoe 2 жыл бұрын

Thanks for posting how you fitted it. I was wondering about the table top, I know you bought it separately, was it specifically made for the swivel stand? And I was wondering if the table top that came with the van could be used, by fixing the bracket onto it? If the bracket comes with the stand, I presume it could be fitted to almost any table top? I'm asking all of this as I'll be fitting it when I eventually get my new pulser. Thank you.

@jimandkay 2 жыл бұрын

Yes you can fit any table top. All fittings come with swivel leg etc. we use the old table at the rear to extend kitchen work space, it creates an L shaped kitchen. 😁

@55glencoe 2 жыл бұрын

@@jimandkay thanks, I remember you used the original top as an extension now.

@jennyanderson6023 26 күн бұрын

Thanks for helpful video Jim, we are going to install swivel,, do you have a link for the table leg you used? Thanks

@jimandkay 26 күн бұрын

I think it’s in the video 👍

@jimandkay 26 күн бұрын

If not let me know and I will try and find it 😀

@jennyanderson6023 24 күн бұрын

@jimandkay hi, watched the video again snd couldn't find a reference to the table brand etc, if you do have the name would really appreciate it, seems to be quite a few similar and yours looks stable and good quality.

@jimandkay 24 күн бұрын

Hi Jenny, have a look at these www.ebay.co.uk/itm/394345353393?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=g0r8zzbjsge&sssrc=4429486&ssuid=BYpzWtZeRrS&var=&widget_ver=artemis&media=COPY Black www.ebay.co.uk/itm/394939168735?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=g0r8zzbjsge&sssrc=4429486&ssuid=BYpzWtZeRrS&var=&widget_ver=artemis&media=COPY Table www.ebay.co.uk/itm/164650720823?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=llj7XRhDSq2&sssrc=4429486&ssuid=BYpzWtZeRrS&var=&widget_ver=artemis&media=COPY 🤞

@jennyanderson6023 24 күн бұрын

@jimandkay thanks Jim, have ordered😁

@irenedale5256 2 жыл бұрын

Hi Jim and Kay, thanks for showing us how you did the table-brilliant! Did the metal plate that was on the inside of the seat, by the heater tube, come with the table leg or did you have to sort that out yourself. As to the table top, did you experiment with the positioning first before you actually screwed it down? A different topic now, your carpet tiles look great - nice job, did you stick them together with tape (on the underside)? Really grateful for your help. Thanks again. 💕

@jimandkay 2 жыл бұрын

Hi Irene, thanks for watching again. Yes the plate comes with the table leg and do the bolts. I did experiment before screwing the plate to the table. The carpet tiles are simply placed down but the joints taped from underneath . I hope this helps. 😁👍

@irenedale5256 2 жыл бұрын

@@jimandkay good morning to both of you. Yes that does help. Thanks again. Always enjoy watching your videos - you both make me smile. 😁💕