Will It Run? International Harvester B275 Part 2
Рет қаралды 12,077
Жыл бұрынIn part 2 of our series on the restoration of the International Harvester B275, we finally get the engine running!!! However, this then leads us to more issues and problems with this tractor. It's starting to look like being one issue after another with this beast.
Part 1 is here: • Abandoned Internationa...
Join our beekeeping channel here: / @honey-yb5kt
Thank you for watching this video. Our website has all our old videos, and is a great archive for scrolling back through them all. It can be found at annoydad.com
We can be reached by:
Sending an email to annoy@annoydad.com
Twitter: / annoydad
Facebook: / annoydad1
If you wish to help us out, our Amazon wish list can be seen here: www.amazon.co.uk/hz/wishlist/...
@bobpaterson1845 Жыл бұрын
What also might help when starting is to have the lift arm control lever in the down position which will stop the hydraulic pump from building up pressure with no where for the oil to go, 👍i have exactly the same engine in my B250 and find it actually starts better without the cold start being used 🙄 that tractor would be well worth saving as i think you would find it would out perform the dexta no problems and depending on which 35 you have give it a run for its money 💪💪
@johnmccollchristianteachin3150 10 ай бұрын
Great video. Useful too for my B250, which is basically the same engine setup.
@vintagetractorollie9421 Жыл бұрын
Good nice to see it come to life again
@lukechamberlain7398 Жыл бұрын
Howdy, I've picked up a B250 (~1955) with similar problems and setup as the B275 by the looks so these videos very helpful and already answered a lot of queries thankyou. I've got issues with the glow plug setup and replacement ones got in Oz slightly longer than original and were shorting out. Will stay tunes though to see how you go!
@holyfists7765 8 ай бұрын
Amazing work you put in to make it run again. Great video, will there be a part 3 of this B275? Would like to see if you can free up the fan and also fix the leaks.
@Roger-dz8xy 8 ай бұрын
Tu a toute un ménage a faire mon boy😊
@welshwarrior797 Жыл бұрын
Nice 😀
@traderjack6151 9 ай бұрын
Throw away that starting fluid! Use the glow plugs, if that engine were a Perkins your piston ring lands are broken now , make sure it’s full of oil
@stevieb931 3 ай бұрын
Did you end up fixing the water pump
@CaptYellow331 Жыл бұрын
The breather is the oil gauge line 😂
@AnnoyDad Жыл бұрын
Thanks
@CaptYellow331 Жыл бұрын
@@AnnoyDad you can buy a new water pump for like 180 dollars
@CaptYellow331 Жыл бұрын
It’s on the other side of the engine 😂
@zonie1953 Жыл бұрын
Mate , have you noticed the crank and belt rotate but the fan and water pump do not move ?
@CaptYellow331 Жыл бұрын
The firing order is 1-3-4-2
Grandad's Blowing Smoke
Рет қаралды 17 М.
Clint's Hobbies DIY
Рет қаралды 18 М.
WHY THIS INCREDIBLE ENGINE FROM 1916 IS PROOF THAT MODERN EQUIPMENT IS A SCAM & OLD STUFF WAS BETTER
Official Welding & Farming Archive
Рет қаралды 1,5 МЛН
DontbeWily
Рет қаралды 56 М.
Tac Tech & Trail
Рет қаралды 2,8 М.
Lawrie's Mechanical Marvels
Рет қаралды 44 М.
DontbeWily
Рет қаралды 207 М.
Kingofnigte
Рет қаралды 6 МЛН
Crafts people
Рет қаралды 6 МЛН
Мотомалышка Алина
Рет қаралды 6 МЛН