I got our family’s 60 back going. It was slightly stuck. I let it soak in PB blaster and some Marvell and I just put my truck in gear and just the small pull of the truck without throttle got it spinning again. Wasn’t stuck bad. I let it soak in Marvell for about a week spinning by hand to lube up the best it could. Got it started. Smoked like that really bad the first time. Cleared up after the Marvell and stuff was cleared out. Love these old tractors

Thanks for giving it life! Now it will be running in 2053! It might even make it to 2100!

So glad u saved it

Good job. Started driving Dad's '54 model 60 on the baler in 1960, at age 9. Darn good tractor.

First time watching tractor sounds great that smoke will clear out when u start working it!!

Great job!

Very cool Caleb

Just found your channel and love the video. Glad you got it running and learned some things from it

Grease was definitely a bad idea. It sounded better and it will get better the more you run it. Those old tractors were built to work.

You can always spin the fly wheel manualy, when the battery is in question😉

sweet tractor tho, gotta love the steering assembly

Good job

Hell yea brother 💯 i love it great job 👏!!

Just fired up a 1941 B that was Sruck. Used ATF in the cylinders and left it for a week before I could turn it. Hand started it today as it doesn't have an electric starter. 82 years old and hasn't run in a few years but did today.

Just liked and subscribed. It will be a handy tractor. Good used 38 rear tires are hard to find.

Tuve uno muy bueno ❤❤❤

Every one can learn with alots of tinkering and Even anyone can learn something new On aney Day

I used a grease gun to free a stuck Case tractor engine but filled the cylinder with AFT first then only used the grease gun to pressurize it. It worked well because of a hyd. pump on the front and a torque converter drive I had no direct way to turn the engine. On the JD you could not fill the compete cylinder with ATF because of the horizontal engine but you could fill part if it. I recently broke free a John Deere 50 that took three things, it took some penetrant, heat and bruit force. I heated the block to about 250Fwith a heat gun in the water jacket, then let it cool. It runs good now.

Wow

Best get those drivers to the co-op for a quick patch they look like hell!

Me gusta lo antiguo

Just need some rear tires and shes ready for the feild

I have been hit with a magneto on a two cylinder and I am not sure it wouldn't light off that grease if given the chance

LOL YOU GUYS ARE FUNNY!!! lol 🤪😂😲

Get yourself a flat belt and belt it up the 830 so you don't need to worry about batteries.

You should have used a 32 to 1 mix gas and trans fluid

I think it'd be more important to get the tires all fixed up so you could actually drive it when you get it to run

Brake clean was probably not the best thing to soak the cylinders in to get rid of the grease. Had the cylinder only been oily, you'd scoured up the cylinders more so than they already were pretty quick. The grease probably saved you alot of trouble with that. And if you haven't found out already, don't use those horizontal cylinder deeres on normal PTO driven equipement, you'll shear alot of shear pins under load, which is one reason I don't care to use those tractors. Sounded pretty healthy once she fired though!

Hopefully you won't have any issues with mosquitoes with all that smoke. 😉

Fill the crankcase full of trans fluid let it run the transmission fluid will free the rings and clean the engine do that 2/3 times drin and refill 2/3 times

I wondered about guys pumping grease into cylinders, then removing grease?

Some poor farmers kids didnt want to carry on farming.

So obvious you're only hitting on one cylinder that would be probably number one but the way it sounds

How much grease made it into the crank case???

I think a lot of these tractors ran when parked. One probabally passed away and they just sit because no one wants them or takes interest in them

Probably may have been better with hydraulic oil pressure

Help! How much oil it consumed!

Pull. It. New. Plugs

Looks like a bird's nest that flew out of the exhaust 😂

🚜🚜🚜🚜😎😎😎👍

Kinda like bottle feeding a calve.

Don't you have another tractor with a belt pulley that you can spin it over at engine speed?

those rear wheels are definitely not original size. original ones were much narrower. I used to drive a tractor just like it.

Kinda spoiled it right off the bat showing it start lol saw it no need for the rest of the vid 😅

Water pump on a 60?

Arnt them 6 volt systems

Its just running on one cylinder

Duuuuh, tear the fricken engine apart and clean it properly, unseize the rings. Thaat's soome lazy butthead trashpile mechanic techniques. It's doing more damage to the cylinders.

First time watching tractor sounds great that smoke will clear out when u start working it!!