Will it Work? Making a Honda GX390 / Clone Compatible
Рет қаралды 60,715
21 күн бұрынA few years back I did a video series on a trashed NAC NKG generator (NGK-7000H). I got it running and making power, but when almost done the stator failed. I harvested the engine and put it on a shelf thinking I could use it at some point. Its been on that shelf for over 2 years. A lot of generators have come into the shop that needed an engine. The Honda engine has the standard Honda clone tapered shaft, but a non standard bell housing. Because of that, I cannot use it. Will a Honda clone engine end cover/bell housing from Generac fit an OEM Honda GX390 engine? I hope so because that will make the Honda engine clone compatible.
Engine cover came from this generator: • Generac Engine Swap an...
Here is the video series where this engine came from:
NAC NGK Generator Playlist: studio.kzfaq.infoP...
Generator Model Failed Engine: GP7500e (0059432)
End Cover: 0G84420227
Crank Ball Bearing: 0G84420117
Counter Weight Ball Bearing: 0G84420118
I no longer use Harbor Freight Super Heavy Duty Degreaser in my ultrasonic cleaner. Harbor Freight changed the recipe. The bottle previously stated "NON-CORROSIVE". Now it says "CORROSIVE", "do not user on Aluminum". It now damages most carburetors. Recently I have been using Simple Green PRO HD with good results.
Visit My Amazon Store:
www.amazon.com/shop/jamescondon
3-Pound Hammer (ESTWING MRF3LB): amzn.to/3vWQFSB
Assembly Lube (Permatex 81950): amzn.to/4cVaKsb
Ball Peen Hammer (ESTWING 16oz MRW16BP): amzn.to/3zzZqna
Blind Hole Bearing Puller Kit (Orion Motor Tech): amzn.to/3Y0SfPb
Brass Dift Set (Mayhew Tools 61360): amzn.to/3XUefec
Feeler Gauge (Lisle 68100): amzn.to/4aY3gnm
Gasket and Oil Seal Kit (YAMAKATO): amzn.to/3WeL708
Thermal Camera (DEPSTECH DS520): amzn.to/3zzEm06
Torch (Bernzomatic TS4000): amzn.to/3VjyUXz
Alternator, Bell Housing, Charge Coil, Clone Parts, Crankshaft Bearing, Fixed, GX390, Generator Engine, Generator, Hertz, Honda Clone, Honda, How To, How-To, Leaking Oil, Load Test, New Ball Bearing, Oil Seal, Power Quality, Pull Flywheel, Repair, Seal Replacement, Small Engine, THD, Tapered Shaft, Troubleshooting, Valve Adjustment, Valve Lash, Wiring Harness, Wiring
@RuneLar 19 күн бұрын
Find yourself a therapist that cares for your mental health the way James cares for the operation of generators and small engines.
@Justicesdad 19 күн бұрын
Or a wife/husband 😮
@basedWisco715 19 күн бұрын
Don’t find yourself a therapist
@tomsing6384 18 күн бұрын
they do not exist, the only thing that works in the long run is The Savior!
@Kinann 17 күн бұрын
@@tomsing6384 Which one? There's literally THOUSANDS!
@mikesbarn1858 16 күн бұрын
My therapist said I was a lost cause and fired me as a patient. lol.
@KaldekBoch 20 күн бұрын
2021! Should have done an old timey black and white filter on that footage. Feels like a lifetime ago.
@cuttheknot4781 19 күн бұрын
I love how pragmatic and methodical James is and the relaxing (almost Mr. Roger's like) cadence that he carries his work out with. He is very relaxing to watch. He is also very tenacious and determined...great qualities to have.
@johncourtneidge 19 күн бұрын
Yes! A Maritimer I expect!
@mattilindstrom 18 күн бұрын
And of course his good habit of cleaning everything (within reason). Quite important to spot future leaks in use. About the relaxation part, I fully agree.
@DeadKoby 19 күн бұрын
This is one of those situations that you don't know if you can until you try. I hope this encourages others to think outside the box when fixing stuff.
@johncourtneidge 19 күн бұрын
Yes!
@bruceyoung1343 19 күн бұрын
I love the sound of a clicking torque wrenchs in the morning
@jeffjackelen744 15 күн бұрын
Sounds like...victory....
@samjackaman1928 19 күн бұрын
James, I hold you and Mustie1 both personally responsible for my ever expanding small engine obsession! 😂, I’m constantly trawling face book market place for small bargains. Thanks to you both, I find repairing anything like this quite therapeutic and a good way to unwind, and watching you and Mustie1 takes all the fear out of getting stuck in, as I know what to expect. Keep the videos coming James. 😊
@WJCTechyman 19 күн бұрын
I could definitely add both to my list but also there are composition of Donyboy73, Chickanic, Taryl Fixes All, Steve's Small Engine Saloon and Home Garage/Inside House Garage to name a few.
@octaviofigueroafigueroa9794 19 күн бұрын
Hello. I watch exactly those channels!!😊. Saludos from Mexico
@MikeGervasi 18 күн бұрын
There's no lame in your game, James. 3 years but you got it running again.
@richardphelan8414 19 күн бұрын
Good show Jim I do remember the first part in 21 ,,your series are always informative and matter of fact you cut no corners and do things the right way ,complete with instructions of Why
@craigvenard2507 19 күн бұрын
I’m glad the magnet on the flywheel made you chuckle!!
@WJCTechyman 19 күн бұрын
I thought that was funny, he reinstalled the flywheel but didn't align the magnet away from his work.
@GNX157 19 күн бұрын
Impressive the ability to reach back in archive footage and link the past and present in a cohesive manner. That’s high production value.
@RiverratGoRVing 19 күн бұрын
Great save James can't wait for update on powerhead install and test run. Keep posting and hopefully some small engine shops see this and hold on to parts that can be reused and sold. Tks as always for your information that you put out there for those that still DYI our equipment. Michael
@drunkingsailor2359 19 күн бұрын
Jim, thats some fine work you did there. Much appreciation to you for being meticulous in your procedures.
@swallowinn4410 19 күн бұрын
Hello James: Well done again. Your attention to detail missed a small bit that surprised me. Possibly you corrected the bent fins on the starter housing off camera. It will not make the engine run any better but esthetically it would look better if they were straightened. Still another unit saved from the land fill and ready for another 30 years of service. Keep the quality up and the videos coming.
@melkiorwiseman5234 19 күн бұрын
Arrived in time to give "like" number 225 and finished the video at "like" number 512... and counting. Good work, James. Not that you need me to tell you that. 😄
@MikeeonYouTube4 19 күн бұрын
James,a piece of Perspex,tap the edge with hammer will create a razors edge,it wont damage Ali,this is used in the fibreglass industry to clean moulds it’s very successful,all the best from Perth 🇦🇺👍
@generessler6282 19 күн бұрын
That sounds like a great idea. You mean snap the edge off by hitting it?
@MikeeonYouTube4 19 күн бұрын
@@generessler6282 yes,hang the edge over something solid,tap with hammer it brakes off @an angle,when it gets blunt do the same again 🇦🇺👍
@bigrickyricks 19 күн бұрын
Not related to this video specifically, but this week I fixed a go kart using the James-Condon-gas-tank-derusting method! Your videos definitely help lots of people, I’m sure.
@EvaderGuy 19 күн бұрын
Well, Professor, I wouldn’t blame you a bit if you charged tuition for these classes, uh, I mean videos. What a great learning experience watching you work! Thank you.
@MitchEllis-dn9lf 19 күн бұрын
@@EvaderGuy yes some junior college is missing a heck of a small engine and generator instructor.
@martyb3783 19 күн бұрын
Its always interesting watching you work your magic on these engines. Well done.
@rx78nt1alex 19 күн бұрын
You don't know how helpful this video is. I have a BlackMax that has the exact same engine and weird 2 part crank case cover with a bad stator thats discontinued. If this goes well for you, it looks like a way to bring that BlackMax back to life.
@TheShawna1 19 күн бұрын
For blind hole removal try packing with heavy wheel bearing grease behind the bearing with a very close fitting wooden dowel wack it with that heavy hammer hydraulic pressure will pop it right out.
@geoffmolyneux9173 19 күн бұрын
Wet small chunks of paper works when heavy grease goes through the bearing. Pound in the paper chunks using a bolt that fits the bearing id hole. Another trick when installing the bearings is to grind old bearing race that is tight, and use that old bearing to tap new bearing in
@lot27a 19 күн бұрын
Blown away by this video James. I wish I had half your knowledge. This is my retirement hobby in the making. I'm convinced these motors (Vanguards, GX's) should last forever for the average consumer with just the minimum maintenence.
@jcondon1 19 күн бұрын
They usually do, if taken care of.
@WJCTechyman 19 күн бұрын
Honda engines for sure, Vanguards still don't hold a candle to Honda or Kohler Command Pro...Honda clones, you name it, it will beat Briggs. Briggs engines were incredibly temperamental at times and the one Vanguard was no exception. Now that they are made in the States instead of Japan, I can see no good happening to the Vanguard line. Toyota Group knows how to make engines, it's one of if not the largest auto makers on the planet. That said, Toyota doesn't produces nearly as many engines as Honda and Honda produces more engines than Briggs. Granted, Briggs has been known to produce more single cylinder air cooled engines but Honda has more experience as it makes engines for almost anything including cars, motorcycles, power equipment, marine, combined heat and power units, performance racing, air craft etc. It's also funny that Briggs and Stratton companies also use Honda engines on some of its top of the line equipment. The Ferris FW15 wide-area lawn mower is powered by the vertical shaft variant of the engine in this video. Snapper's top of the line walk behind 21" mower is powered by Honda's GXV160.
@tomsing6384 18 күн бұрын
the problem is it runs on Gas, got to get ride of the gas
@CrimeVid 18 күн бұрын
@@tomsing6384 not in your lifetime !
@vernt4583 19 күн бұрын
Great job on your expertise on Honda engines 🎉❤. Enjoying your videos from East Texas.
@donnaber4918 19 күн бұрын
James you need to repaint the front cover to Generic orange. Overall you did a super job.
@jcondon1 19 күн бұрын
The engine is going to repower a yellow champion. Hopefully will get that video in the works soon.
@johncourtneidge 19 күн бұрын
Super gorgeous, James! Lovely work! Highly enjoyable! Well done! Thank-you!!
@realimike1971 17 күн бұрын
James, you just saved me time and money....THANX ALOT I watched several of your videos on drilling out jets to resolve surging problems, my pressure has always surged and never knew how to fix it, until I watched your videos in idle circuits, I found my idle circuit and took your advice to the letter and was patient, till I fixed the issue. I had to drill out the idle jet 3 times to get the results I wanted. Thankyou from California. Liked, subscribed and donated.
@jcondon1 17 күн бұрын
Thanks I appreciate it. Glad to hear it running well. A lot of new engines surge from day one. I find drilling that jet is the only way to get it running right.
@brianwood5220 19 күн бұрын
Great job, James. At least it didn't cost you too much to get it back to top running order. Thanks for sharing.
@jeffreyandreas7514 19 күн бұрын
Great job and great video Jim! Very informative and we’ll be looking forward to seeing that engine powering a generator again!
@donprater2754 19 күн бұрын
The master did it again. Good video James.
@Bradleyscience 7 күн бұрын
Very well done, we appreciate all of your insights, thoughts, shortcuts and experience, it truly makes it much easier for many people. Cheers
@WJCTechyman 19 күн бұрын
Interesting video, as always. I am not at all surprised that a 29 year old Honda still starts and runs as I have a Honda GXV120 powered Honda HR214 lawn mower that still starts after roughly 40 years and even older Honda flathead G and GV engines on two Honda snow throwers and a Honda tiller, over 40 years old a piece that are the same. The tiller was also once a piece of rental equipment and well used and/or abused. Of all of the engines I have had over the years, I put Honda at the top of my list (and that includes the clone engines I have bought as well, one of them being a direct clone of the GX390 you have in this video that's on my 5500VA running generator as well as the 420 cc monster on my Cub Cadet snow blower). Closely following are Echo, Kohler Command Pro (my two 12.5 hp Kohlers are getting harder to find parts) and Tecumseh and dead last by a fair distance is Briggs and Stratton.
@AMAZING-nx4ex 18 күн бұрын
Nice work so easy to watch you doing your work. You make it sound special and happy with what is going on.
@DanKoning777 19 күн бұрын
Like always another great video-and one of the best parts was at 1:24:20 "...in the next few weeks you're going to see this engine again..."
@guataco 19 күн бұрын
You really are a Dr. Frankenstein of small engines. Congrats.
@amilian74 19 күн бұрын
great job as always, interesting the way you changed the bearings and oil caps from both sides of the engine, I think this is the first time I´ve seen you do that
@wb8ujb 19 күн бұрын
I have been working on engines for many years. I always wondered what that spring was on the governor linkage. Thank you for that information. Thanks for your video's as well. I find them very informative.
@luissimmons654 19 күн бұрын
Thanks for been so kind i love watchin your videos please let me know each time you put up a new one
@rodneymiddleton9624 19 күн бұрын
I always wondered how close the castings were to the original Honda casting. I use a transmission assembly lube tacky grease that holds the lifters in nicely. Great job!!!
@nicklutz61 19 күн бұрын
Very interesting video. A "ClonDa" is born! Keep up the great work. Closing in on 200K subs - congrats!
@jcondon1 19 күн бұрын
Thank you!
@williambikash6645 19 күн бұрын
When banging new bearings into the endplate, Chill the bearings which you did. A little lube on the bearing outer race and and in the endplate and heat it a bit longer. Put a solid piece of hardwood on the concrete floor and carefully hit the bearings with your large hammer. Your lift absorbs a lot of the energy from the hammer blows. I saw the large bearing fall into place but the small one took to much pounding.
@RC-fu6hg 19 күн бұрын
Amazing as always! 👍 now that’s some recycling ♻️ at its finest! Often have I wondered if swapping out covers could work. 🤔 Well you answered that question with one awesome video!
@EugenMoisa 19 күн бұрын
minute 13:30, stop hammering the sockets.. if you worked in Germany and did that, you'd probably be fired 😅😅 Great video as always
@andrewgrace4410 19 күн бұрын
Awesome troubleshooting James 😊
@davidschipsi1316 19 күн бұрын
The balance shaft like you showed needs to be timed. The crankshaft counter weights balances the piston weight and momentum at top dead center and bottom dead center. When the crankshaft counter weight is at 90 degrees now the weight is too much and causes crankshaft counter weight vibration because the weight and momentum is much different and is out of balance at that point. Here is where the balance shaft does its thing, it counter balances the crankshaft counter weight at the right time 90 degrees with opposing force.
@jcondon1 19 күн бұрын
I did time it. Also out of time besides the vibration the crank counter weight will hit the balance shaft weight.
@christophermarshall5765 19 күн бұрын
Runs great!! 12V charging works properly too. Nice job!!
@scottpace578 17 күн бұрын
It’s all about having parts! Great video!
@watermanone7567 19 күн бұрын
Excellent work James. Thanks for the video.
@generessler6282 19 күн бұрын
Nice as always. As you said looks like it had quite a few hours with wonky oil at the end. Hope all your good work won't be for naught due to something else going sideways in the near term.
@almclean4835 17 күн бұрын
Another great video James.
@YukonHawk1 19 күн бұрын
I love your videos. I learn something new everytime.
@RichardLiebert 9 күн бұрын
Attention to detail(s), as ALWAYS! great Video!
@davidmonteil6340 18 күн бұрын
Great work James!! I never thought I would see you kind of downgrade (of sorts) a Honda engine lol, but hey it worked! Your patience, knowledge, skill, and tenacity are quite admirable. Hopefully that cover will be in similar quality to the rest of the Honda motor. It should be no problem. You saved that engine, electric starter and all to work with a clone power head! At some point I was listening to hear you say "scalpel" but "razor blade" is close enough. I will enjoy seeing that motor powering up a large generator in the future. James has rebuilt it. He has the technology! I think that doctors should also have some additional experience rebuilding motors, and be successful at it before working on us...Yep...lol
@robertgad3269 16 күн бұрын
You are a talented guy. That is hardly news, and some of the talents are obvious. However, you have one more talent that, frankly, is a surprise to me and something I’m sure you never thought of: for some inexplainable reason, you are able to hold my attention watching you scrub old oil off engine parts with WD40, a scrub brush, and a handful of paper towers. I, for one, find that impressive. Thanks.
@mjg263 18 күн бұрын
Wow, I’m really surprised the Honda clone oil sump section fit the genuine Honda engine with no issues. I always thought they changed things just a little bit on the clones to prevent legal trouble, or at least to cut manufacturing costs. Amazing job!
@bryangilmer671 16 күн бұрын
Came here to say this
@alanstalker5499 13 күн бұрын
An excellent video. Thanks Jim.
@walkertongdee 19 күн бұрын
Now everyone knows why the Honda GX series is the most copied engine in the world, but most people prefer low-quality cheap crap that doesn't last, well not me I will always choose Honda quality. I have two 20-25- year-old Honda GX series engines and I never replaced a part.
@jcondon1 19 күн бұрын
The generator I am going to put this on had a 2 year old clone engine with about 200 hours that failed. This Honda is much older and I bet will run the generator for many more years.
@walkertongdee 19 күн бұрын
@@jcondon1 I longtail (mud motor) deep into the Thai jungle, I need a Honda...
@michaelmichaelh6103 16 күн бұрын
Hi.. I've been a mechanic for decades, much easier to remove gaskets with products like crc gasket remover..saves time, just have to be cautious of sensitive materials that may be damaged...better then hitting gear teeth with scaper...keep up the great work you do sir...cheers.
@user-ff2bj9wc1e 19 күн бұрын
Nice job James 👍
@CheapThrills66chevy 19 күн бұрын
James, you should try a pull gasket scraper. I have the Wilde Tool 516 I got off Amazon and I found it to work really well. I feel like it gives me more control and it is much less prone to gouging when scraping gaskets on softer substrates like aluminum. The carbide scraper is great on harder material. Love your videos. Keep up the great work.
@jcondon1 19 күн бұрын
Will take a look. I have a carbide scraper. Works great, but on aluminum not my first choice.
@GNX157 19 күн бұрын
23:40 A suggestion for if you needed to use a socket to tap in, is to put some grease in the back of the seal in the cavity where the lip seal tension spring is (if it uses one?). The grease will help keep the spring from popping off from vibration when you hit the socket, which you may not see happen since the backside is hidden by the bearing.
@loucinci3922 18 күн бұрын
Enjoyed the video. Thanks for sharing
@MitchEllis-dn9lf 19 күн бұрын
As usual an excellent video.
@myrandabrown 19 күн бұрын
Another great video ❤
@arthurbiringer5676 19 күн бұрын
Another great job!
@peterouellette3874 19 күн бұрын
Nice going, James
@johnsalmon2501 18 күн бұрын
Great video! Enjoyed watching it. Thanks
@jcondon1 16 күн бұрын
Glad you enjoyed it!
@ceejay6882 19 күн бұрын
The exacto knife kits have mini chisel shaped blades. They work really well in tight spots.
@user-kf6my9uy9m 19 күн бұрын
You do good work!
@grahammctygue724 20 күн бұрын
Hope staying cool n dry 🎉🎉😊😊
@geraldharkness8830 19 күн бұрын
excellent james
@paulravitsky2898 14 күн бұрын
Measure the voltage on the charge coil. If it AC, then you will need a diode in series to charge the battery. If the output is DC, you should be good to go. You might b able to use the diode test on your meter depending on the coil resistance. If you get the same reading whilst reversing leads, you will need a diode. If you get a low reading one way and a high reading the other way, there is probably a diode in the lead. My experience with 2 cylinder Honda engines with the same charge coil is you're gonna need a diode. Great save!
@mnemonicmoniker4101 7 күн бұрын
James Condone is the Bob Ross of small engine repair. If you’re old enough, you know what I’m talking about.
@mnemonicmoniker4101 7 күн бұрын
Sorry. Condon. Dang it. Well, he put a happy little bell housing over there.
@jcondon1 6 күн бұрын
I used to watch him on PBS
@ronaldtodd4819 19 күн бұрын
I grew up in my grandfathers small engine repair shop and enjoy your videos a lot, however I do think you get carried away with the torque wrench.
@OnTheEdgeNow 19 күн бұрын
They used to make a spray gasket remover I used for gaskets like that when I worked on cars in the 80s. Spray it on, let it set for 15 minutes, and it would soften the gasket right up. I am not sure, but I think it was made by Permatex. Don't get any on an open cut if I remember right.
@Joserocha-wm9de 19 күн бұрын
Hi James💡 , we are back 🙃🙂
@philliphall5198 19 күн бұрын
Good job 👍
@richardtaylor7199 19 күн бұрын
Great job
@luuk-out-below9804 19 күн бұрын
Nice one!
@MitchEllis-dn9lf 19 күн бұрын
The magnet on the flywheel was giving you competition to insert the bolt and to get you socket and extension back. LOK
@oemytech 19 күн бұрын
Great video.. But, would have put the second coil in as it would be a lot of work to do it later.
@jcondon1 19 күн бұрын
True, but I have a generator in mind for this engine and the second coil is not needed. Actually I don’t think it needs any coils.
@oemytech 19 күн бұрын
@@jcondon1 that makes sense.
@neiltheplayer 15 күн бұрын
not sure if someone has asked this before, why don't you use a pressure washer and degreaser to save the hand scrubbing? then use the brush afterwards. Might save a bit of elbow grease in the long run. Thank you for posting this.
@angusshapland2273 2 күн бұрын
There’s a difference between back fire and after fire. The solenoid valve on the carb main jet is to reduce the possibility of after fire caused by unburnt ( ignition killed) fuel being sucked into a muffler may have red hot rough internal flanges etc that then ignite the raw fuel with a quite violent pop.
@billcrocker1054 18 күн бұрын
James, you should make a video on how you make videos. Please show us how you record, edit and post? What software do you use? Over the years you have gotten very good and I have watched them all.
@LostDeadSoul 19 күн бұрын
It would be lovely if you had/used an hydraulic press for those bearings. I mean I myself have hammered many bearings in. But having an hydraulic press brings more satisfaction, I think. Anyway, keep on keeping on bringing good content.
@myrandabrown 19 күн бұрын
Well, that exhaust valve explains the leaky seals at least.
@redneckbryon 19 күн бұрын
42:38, you drop something right around this point in the video. I had to watch it twice to make sure it was you and not me, lol 1:02:20, did you know just because it meets that rating, doesn’t necessarily mean it’s that old, it’s just in compliance. I have a Craftsman Tractor it meets the 1998 emissions compliance, but it’s a 2003.
@raymondsmith4808 19 күн бұрын
Very nice of you to explain.
@ron827 19 күн бұрын
Before removing a dirty cover, "I" prefer to remove as much dirt as possible from the area to prevent internal contamination.
@larrykelly2838 19 күн бұрын
Great video
@jcondon1 19 күн бұрын
Thanks
@jerryhouston5400 19 күн бұрын
What is the degreaser you use for scrubbing off the caked on oil?
@MitchEllis-dn9lf 19 күн бұрын
Is there a reason you prefer the breaker bar over using your smaller or larger impact to break bolts free and remove them?
@jesterr7133 19 күн бұрын
I can really appreciate how thorough you are with your work. It is nice learning how to do things properly. It is a pleasure learning from you. I think you are a perfectionist. I recently worked on an engine for a push mower where I was unable to remove the blade adapter. I could only open it about 16 inches. I was barely able to clean the gasket surface at all. Even after breaking one of the sump cover bolts and tightening all of them by hand with no torque wrench, it is still sealing perfectly and doesn't leak a drop. I have never owned a torque wrench. What is the benefit of using them? I am looking to purchase one soon when I sell my next machine. I don't understand the benefit of using one, but i would like to understand it. Why is it necessary to use one?
@jcondon1 19 күн бұрын
For some things you need it, like on the connecting rod and flywheel. Most you do not. But I use one if the manufacture specified a torque value. Just helps ensure you do not break a bolt and applies even pressure on the part being secured.
@w.ottopeck9619 19 күн бұрын
Great video! Do I have to wait a week till you finish the build? I’m looking forward to it
@jcondon1 19 күн бұрын
Next week starts a video series on a go cart, then will use this engine after that on a generator with a blown engine.
@fascistpedant758 19 күн бұрын
@24:25, You could have tilted the engine to the right so the lifters wouldn't slide out.
@MitchEllis-dn9lf 19 күн бұрын
If you got the cam back in with the valves and springs in tact odds are the push rods are fine.
@gerardrusso9642 19 күн бұрын
cool video
@JpJp-zd7vu 19 күн бұрын
Another superb revival James & a plethora of knowledge right along w it , as usual ! Referenced you're MZ360 swap to Responder gen head last week , and pulled off an identical swap . Currently finishing up a Generac 5500EXL , carb kit & filters due in a few days . Have a Techimcal question, need a complete cyl head for a Honda clone 18hp single cyl , Gen 2 . Unit is a DuroMax XP 10,000 EH . BLOCK #'S - MF192FD *170913337* Curious if a cyl head from say a 15 , or 16hp would be the same head ? Or even a cyl head from a twin cyl emgine of slightly lower ratimgs . I've found the actual cyl head on Generator GuRu , but its upward of $240 + . Customer wants to try a cheaper route of possible ?
@melparker7711 19 күн бұрын
You need a Dake arbor press.
@benrobles752 19 күн бұрын
Another enjoyable video, James. BTW I'm down here out of Houston running my B&S 8250/5500 Storm Responder. Going on four days, shutting engine down to refuel about every ten hours and checking the oil. I am using Mobil 1 full synthetic 5W-30. I need to get your shipping address to send you some parts from an aborted generator repair project.
@jcondon1 16 күн бұрын
Jimcondon76@gmail.com - good luck there in TX
@tomsing6384 18 күн бұрын
Hi, James, could you do a little teaching on the Loading in's and out's of home generation, would the old rule of 80% work in most cases?
@kevinklassen8199 18 күн бұрын
Nice!
@jesterr7133 19 күн бұрын
The governor spring will cause surging? I have been fighting a GCV160 revival for a year. I have replaced the entire fuel system, and replaced or cleaned everything in the ignition system, but it still occasionally surges. That is something I never thought of.
@jcondon1 19 күн бұрын
The spring that goes on the governor rod is an anti surge spring. Without it, the play where the rod connects to the carb and governor arm can cause surging.
@andyhamilton8940 18 күн бұрын
Seems like the governor hear should just pop out of the housing?
Garena Free Fire Global
Рет қаралды 60 МЛН
$150 Honda Clone vs $600 Honda? Let’s settle this! Fuel Efficiency, Horsepower, Durability, Starting
Project Farm
Рет қаралды 4,8 МЛН
Pacific Northwest Hillbilly
Рет қаралды 96 М.
ITS ALWAYS #3! 2018 Hyundai Tucson 2.0L Lawsuit Engine Launches Wrist Pin Into Orbit! ONLY 90K MILES
I Do Cars
Рет қаралды 192 М.
Фото радужки глаза Владимир ScreenEyes
Рет қаралды 6 МЛН