Will Wide Wheels Ruin My Front End? || From The Inbox

Рет қаралды 329,492

Күн бұрын

Ready to run wide wheels but worried you’re gonna ruin your front end? Will wide wheels destroy ball joints? Worried about replacing wheel bearings often? On this week’s episode of From The Inbox we touch on wide wheels and how they could affect your truck. Have any questions you want answered? Drop a comment below or inbox us!
Check out Wheels and Tires here: customoffsets.com/wheels
Check out the gallery here: customoffsets.com/gallery
Check out Lift Kits here: customoffsets.com/lifts
Add your truck to the gallery here: customoffsets.com/add

Пікірлер: 359

@CaptainPaddys 3 жыл бұрын

Love hearing about Kryptonite, I threw every part they made at the time 3 or 4 years ago on my front end and launched a 2500hd 9 feet in the sky. Kryptonite parts held (no surprise) motor mounts and radiator not so much. Totally worth it.

@hdz12ez 5 жыл бұрын

I would add that when the vehicle is in forward motion, the wheels naturally want to go outward(toe out), so manufacturers intentionally make alignment specs slightly toed in to combat this. Throw on some wide rims and tires with a large negative offset and you're adding tons of stress on the suspension. Especially the tie rods. Also, driving here on Michigan roads is absolutely sure to destroy your suspension and wheels, factory or otherwise. Not sure how Wisconsin is but Michigan is 3rd world. Good info in this vid though.

@lynnmckenney1987 5 жыл бұрын

I'm a fan of small wheels and lots of tire (on a truck). The functionality of small, *sort of* light wheels + big tires > huge, heavy rotating mass with low profile tires on a 4x4.

@-._._._-_._._.- 5 жыл бұрын

Shhh, this isn't the place for practical vehicles, this is the place for people to donk their trucks.

@solidoustopher 5 жыл бұрын

I've been looking into a good set of 18's to go into my 33x12.5s. I do love my 20x12s, but I hate worrying about them all day on the road.

@praedyththelost3753 5 жыл бұрын

Everyone has their preference. You're more into real off road capability. Whereas a lot of these newer builds are more street truck inspired. Its like a fusion of the two. Still got a lift rather than lowering, and big meaty tires. But now these street trucks are trading off road meaty for street tires that still look meaty. You'll see roll pans which are a street thing rather than off road bumpers. I personally like both looks. The new street truck look and the off road/work truck look. Never was a fan of lowered/slammed myself.

@roderick9018 5 жыл бұрын

Yea I went 17 x 8.5 + 10 on 34 x 11.5 aka rides like a caddy now

@killerklown6905 5 жыл бұрын

These trucks they build arent of offroaders they're the walmart get together trucks 😂 bug with less rim more tire you can air down and get more grip and with these truck first hard rock there goes a 600$ rim 😂

@ebaysnipa 5 жыл бұрын

My experience with my 2009 Silverado installing the lift kit with 140,000 miles on her is that Yes, a few months later new ball joints and wheel bearing were needed, just on daily city driving, so I decided to learn who to work on my as much as i can. Thanks for the help, CO.

@caseytodd7632 5 жыл бұрын

That's pretty spot on. Putting a lift on a higher mileage truck will do that really quick. I'm surprised your transmission didn't grenade on you too.

@73powerstroke56 5 жыл бұрын

Actually lifting a truck doesn't cause stress to engine trans or axles. Bigger wheels and tires will.

@hi-wc4kv 5 жыл бұрын

@@73powerstroke56 If you get a lift kit that comes with new control arms,CV axles,drive shaft, etc.

@73powerstroke56 3 жыл бұрын

@J F wider tires create more drag on the drivetrain. But going from 9 1/2 to 10 wide isn't that much of a difference.

@randyirwin3984 4 жыл бұрын

Pretty sure my old bearings were on the outs but I went with Timken bearings on the replacement. Tire size 35" and 2 years later not an issue.

@WBOS72 5 жыл бұрын

Thanks for breaking this down. Another excellent vid.

@JohnWargo93 5 жыл бұрын

Awesome video as always guys!! Very informative!!

@chosenwon5618 2 жыл бұрын

I have a 2 1/2 “ ready lift leveling kit on my 18 Silverado 1500. The kit came with the beefier upper control arms and everything is working great!

@Morpheen999 5 жыл бұрын

Using Kryptonite on my Duramax now, only running 10 wides but I'm not taking any chances with steering components Front end is beefed now!

@jacobn3160 5 жыл бұрын

You guys should do a series like fitment industries does, where they pick a couple trucks from the gallery and rate them 1-10. It'd be really cool to possibly see your own truck on a video

@MrJay3star 5 жыл бұрын

Jacob Nichols they do

@DirtNassty 5 жыл бұрын

They do lol it's called "from the gallery"

@rich7447 3 жыл бұрын

If you are worried about bearing (4x4) look into conventional bearings in a free-spin kit over unit bearings. The bearing spacing is wider and handles the stresses better.

@john21267 5 жыл бұрын

These informational videos are great!

@antiest08787 5 жыл бұрын

I want to run 285/70/17 11 wide. With -12 offset and 1.25" spacers. Will I expect a lot of wear? '15 4runner

@joshr7434 5 жыл бұрын

Here at customoffsets we believe 4in spacers and 24x14s are safe on a 1997 K1500.

@suavehouse5150 5 жыл бұрын

Lol I have a 97 K1500 with 24x14 and 4in spacers damn it!

@ebaysnipa 5 жыл бұрын

blue333 hard to believe my friend.

@joshr7434 3 жыл бұрын

corylocher1 yeah lol we know it’s just a joke

@itsvortex1107 3 жыл бұрын

97 k1500 here as well, late to the party but I’m currently wheel and tire shopping 🤣 hard being an 18yo on a budget

@joshr7434 3 жыл бұрын

itsVortex contact next on IG josh.z71

@workplaytv 5 жыл бұрын

Subscribed. Love the videos. Do you guys ship to NS Canada. Would love a price on a set of black wheels and tires for my 17 f250 lariat.

@CustomOffsetsTV 5 жыл бұрын

We ship world wide! Shoot us a quote form to customoffsets.com/quote !

@patrickfuller6018 5 жыл бұрын

Parts are replaceable... How boring is it to live life under the "manufacturer recommendations"... I wouldn't know, x14s on everything.

@norcalsrt1214 5 жыл бұрын

Classic d-bag surely have a whole wardrobe of tap out shirts and white spy sunglasses

@yeswereact5283 5 жыл бұрын

I think your Buddy Erick here got picked on in school. Clearly projecting his insecurities onto strangers over the internet. 😬

@norcalsrt1214 5 жыл бұрын

@@yeswereact5283 naw we see all these dbags and the mall crawling turds here and then they went a step further like all dbags and created the Cali lean. Seen one d-bag truck seen them all

@jacobn3160 5 жыл бұрын

Erick Varela How's he being a d-bag? He just likes 14 wides and puts them on his truck. Cali lean was created because people wanted to be different and stand out from all the other lifted trucks. If you don't properly aim your headlights or something like that, that's ignorant. What makes you think because he has 14 wides he's a d-bag? No hostility at all, genuinely curious.

@norcalsrt1214 5 жыл бұрын

@@jacobn3160 called law of statistics

@thenewlife.pt2724 5 жыл бұрын

Thanks for this !!!!

@nemesis851_ 4 жыл бұрын

2 years later Fuller , you still got a job there 🙃

@alexiscoronado2730 4 жыл бұрын

What wheel hub do you guys recommend for bigger tires im running 37s and mine just went out and want to buy something that will hold

@user-jk8rf2pw9h 5 жыл бұрын

Dang ol dang big ol trucks man

@Man_in_a_Gucci_Suit 5 жыл бұрын

Jeffrey Boomhauer III He meh man I tell u what man that dang ol’ mike judge thinkin renewing da king hill show man I tell ya on fox

@misterbulger 4 жыл бұрын

Im running 315mm wide 33s on my Titan and no issues whatsoever after 115k of heavy washboard and towing.

@rajvirvlogs1313 4 жыл бұрын

Awesome video making amazing truck's 👍

@HAHA.GoodMeme 5 жыл бұрын

1:39 lmao

@jimlahey9796 5 жыл бұрын

Hey you're finally at 200k subs

@thenewlife.pt2724 5 жыл бұрын

I want 16 wides with 3inch spacers

@sarahmachol1609 3 жыл бұрын

Bearings went out at 57,000 miles. Got this ram 1500 a year ago. Installed moog bearings and selling the 20x10 big offset wheels that the truck came with and going back to oem specs. Looking cool isn’t cool when it breaks your truck.

@psychotic_oreo_6680 3 жыл бұрын

Does a spindle drop still change the control arm angles? Vs going with a big strut spacer

@evanveine714 4 жыл бұрын

So I have a stock 2010 f-50. I want to use the mcgouys 6.5 lift with some 20x12 wheels. The truck is clean 90k miles. I’m worried. Do I need aftermarket control arms bearings ect... or is that stuff stock fine?

@adrianmartinez3220 5 жыл бұрын

Talk more about the uniball uca and their benefits

@RabbiTrogdor 5 жыл бұрын

Stronger and better articulation. More vibration transfered to the cab. Can be noisy.

@doyrfan 5 жыл бұрын

So would it be safe to say that if i run an aftermarket wheel 9 wide 18” on a silverado id be ok

@CustomOffsetsTV 5 жыл бұрын

Yes but the only thing you would potentially have to worry about would be the tire rubbing on the control arm or frame depending on what size tires you will have! Check out our gallery and see what other people have made fit on their Silverado including the rubbing and trimming info of each vehicle! customoffsets.com/gallery

@derekhoffman9737 5 жыл бұрын

I prefer 0 offset rims anyways even if it means I can't run much bigger then a 13 wide tire. The weight stays centered but even more stress is added to steering. Having a solid front axle helps as well. I dont mind the rough ride I have a car for the long road trips.

@kenoday7562 5 жыл бұрын

So long as you adjust your alignment specs to match. You'll need an engineering degree to figure them out, though.

@isaacthehorse4038 4 жыл бұрын

I put on 20x14 on a 33 by 12.5 tire on my stock 2500hd Chevy and it runs but it clears it with some trimming

@static.s1082 5 жыл бұрын

Haha, i want to do 35x14.50 tsl boggers with -76 offset on a 1992

@raptordan6851 4 жыл бұрын

It’s a Gm ... driving it stock will wear it out soon enough lol

@MrAnimefox 5 жыл бұрын

I had a truck come in with 14 in wide tires because the driver rear snapped the axle rod so we had to replace the rear end

@edwardkareem6446 4 жыл бұрын

Make a vid on tapper vs straight cut blocks witch is better

@xrickel559 5 жыл бұрын

It's real simple. If you want to play it safe on a daily driver 12 wides on a 1500 and 14 wides on a 2500. Unless you want to get into the world of obnoxiously expensive upgraded steering parts then do whatever.

@mar-mar5.438 Жыл бұрын

I should be good on 10 wides then ? Stock suspension

@xrickel559 Жыл бұрын

@@mar-mar5.438 shouldn't be a problem at all. Ran 12 wides on my silverado for 3 and a half years and never had an issue all stock front end parts.

@mar-mar5.438 Жыл бұрын

@@xrickel559 thank you 🙏🏽 my father said same thing but just want to be sure. I appreciate your input brotha

@xrickel559 Жыл бұрын

@@mar-mar5.438 no problem man

@MiguelARodriguez936 8 ай бұрын

@@xrickel559what was the offset?

@dylanwhite4908 5 жыл бұрын

So I have a 2010 Chevy Silverado 1500 4x4, with some 18 by 7.5 wheels ome. I’m getting a level on it, it already has some cut out around the insides of the finders. What would be the biggest tire I could run with that set up?

@CustomOffsetsTV 5 жыл бұрын

The best thing to do would be to look in our gallery Dylan! It should show a few other people with similar setups and what they got to fit on theirs! Including the rubbing and trimming info of each one! customoffsets.com/gallery

@MakingitMoist 3 жыл бұрын

What if you have small rims and very wide tires. Does it have the same amount of problems has wide rims?

@johnvigil7654 3 жыл бұрын

37x13.50x20 -76 offset on a 06 dodge ram 3500 lifted 6" ... tell me your opinion about this setup.

@christiancullum2891 5 жыл бұрын

Aye my trucks in the gallery

@jimmy4x4socal44 5 жыл бұрын

Correction, GM trucks have tiny tie-rods

@toddmcmahon2648 5 жыл бұрын

but big balls

@Builttolastdenali 4 жыл бұрын

So I get a popping in front of my truck..I don’t have an aggressive offset or anything..with no spacers..full fox length coil overs in the front end and the rear..so like idk what’s the issue..are my tires to wide? They are 20x10 with like -12 off set

@lombardozarateiii6920 4 жыл бұрын

I want to buy some rims for my 07 Colorado but don't know what length of back spacing is allowed to be used on rims for my truck. Does it matter if it's more then 4.5"?

@CustomOffsetsTV 4 жыл бұрын

Check out what others did! It will say their backspacing the descriptions! bit.ly/2OdIjNy

@mattdee9296 3 жыл бұрын

That 5” rc bracket lift looks even better after watching this

@hacksawtheonly 5 жыл бұрын

Hey can anyone help me lift my 09 Ford p71 interceptor? Not for a donk look for a off road look.

@robertwood7208 5 жыл бұрын

If you’re wheeling it, this kind of changes. But these set ups are for the tow vehicle not the off road vehicle anyways. My set up killed my wheel bearings relatively quickly once thy started seeing actual off roading.

@tankdog03ify 4 жыл бұрын

Just buy the best LIFETIME WARRANTY wheel hub bearings at your local parts store, so you can buy them once and just use the warranty, then buy the double wide rear bearings with warranty also, fairly easy to change by pulling the rear axles

@carlmottola5611 4 жыл бұрын

Basically fuller just spent 5 mins saying "yes". Yes big tires and wheels will ruin your front end. I have slightly larger then stock tires on my stock cummins . Yes I take it off Road. That said i did the front hubs. Huge pain. Multiple days of work, and had to buy a torch. It's not a simple thing to do like fuller said

@savage_24v 5 жыл бұрын

For anyone that reads this a 12 wide on a spacer is worse than a 14 without spacers It's not how far your wheel sticks out its how far the inside of your wheel sticks out So a 24x16 with a 4.5 backspace will do the same amount of wheel bearing wear as a 10 with the same backspacing

@Boomerfootball1 5 жыл бұрын

Thanks for the info never realized that. Now debating 10 or 12 wides lol

@brickson98m 5 жыл бұрын

So to simplify, it’s the offset that matters, not the width. I’ve got 10 wides that barely stick out. Cause they don’t have much offset. I do wanna swap to 12 wides with more offset though. Love the deeper dish look

@savage_24v 5 жыл бұрын

actually the offset has nothing to do with it it's all in the backspacing

@brickson98m 5 жыл бұрын

Savage 24v uh.... google “define offset” and a good visualization should come up as the first picture. I think you’re calling the offset backspacing. It’s all comes down to where your hub is in comparison to the center of the wheel

@savage_24v 5 жыл бұрын

if you think about it a 24x12 and a 24x16 is the same wheel except that the 16 has 4 inches added on to the offset/ outside lip of the wheel. but from the mounting point to the inside of the wheel is the same measurement therefore same stress on the wheel bearings

@cbradley621 5 жыл бұрын

What are the best companies that make "true directional" wheels that ARE NOT forged wheels for the people (like me) that have a lower budget?

@CustomOffsetsTV 5 жыл бұрын

Sounds like Arkon Offroad is exactly what youre looking for! www.customwheeloffset.com/store/wheels?brand=ARKON%20OFF-ROAD

@smbmxdirt3427 5 жыл бұрын

If you own a dodge then yes it will ruin your front end. But even the stock front ends fail so you may as well look good

@wubbalo7 5 жыл бұрын

I've got a 2010 Silverado 1500 Z71 4x4 with a 3.5" level lift. I bought heavy duty tie rod ends from RC, and had them installed. I currently have a set of 18x9 with a 33" tire and 0 offset, but I'm looking at getting 20x12 -51 with a 33. I am not going to be running any spacers, so how bad will the damage be?

@CustomOffsetsTV 5 жыл бұрын

Check out the gallery on our website! Its designed to answer your question, just type in your vehicle make, model and year plus the suspension and see what others have made fit including the rubbing and trimming details of each vehicle! customoffsets.com/gallery

@wubbalo7 5 жыл бұрын

Custom Offsets, thank you for that! I’m on the gallery every day! I’m just curious how long I can get away with 12 wides before my tires start pointing towards each other.

@johnnyshell2839 3 жыл бұрын

Not sure if it's relevant but there's a company I used for all my front end parts on my 05 tahoe on 20x10. Mevotech makes some beefy parts. Even Chevy wheel bearings and hubs. Titan xf and ttx parts under mine. 305000 on her still straight and solid

@elijahbrooks8589 5 жыл бұрын

Your shipping ticket says 374 with 16x10

@silverdollar6.610 4 жыл бұрын

I’m thinking of some 24x18 forces on my leveled 2nd gen ram

@kaceskipworth2645 5 жыл бұрын

I’d like to see a video about upper control arms

@kyle-kelliher 5 жыл бұрын

The worst thing is the offset. if you had the wider wheels, but the offset put the weight on the same part of the wheel, you wouldn't have any major issues. Guys trying to get a ton of poke with silly offsets and spacers are going to see alot of wear on the ball joints and bearings. The extra weight of the wheels and tires is just harder on the drivetrain, for the most part.

@georgedunham7311 5 жыл бұрын

G’day mate. I’ve just brought a 1990 Hilux with 33” mud terrains. The issue is when I’m driving quite regularly the car just goes off on its own, and feels like it’s doing what it wants to do, like it drifts off track, it’s like a shopping trolley. Is it the tires that are causing this or something else?

@CustomOffsetsTV 5 жыл бұрын

Bigger tires will tend to wander around a bit!

@tylerinscoe9880 5 жыл бұрын

What's the largest tire you'd put on stock wheels? @customoffsets

@Reverend1776 5 жыл бұрын

Do you have any recommendations on protecting the paint as you mentioned...my 4runner front doors are taking a beating since putting aftermarket wheels on and they don't even stick out tht far.

@CustomOffsetsTV 5 жыл бұрын

mud flap/clearbra is your best bet

@hi-wc4kv 5 жыл бұрын

I'm not sure if they make them for Toyota 4runners, but fender flares might help.

@kenoday7562 5 жыл бұрын

Try a film if you can't find mud flaps you like. www.3m.com/3M/en_US/post-factory-installation-us/paint-protection-film/

@rubenwong9574 5 жыл бұрын

do a monthly front end check and if you're gonna travel to different state check front end make sure is tight stock parts will wear out within 6months at 15,000 miles I got 3inch lift spindles running 33s on 22x12 -44

@michaelburke2824 5 жыл бұрын

6 months?? I've put 125k miles over 5 years on a f250 super duty and have had to only replace one tie rod end!!!!!! No other problems and every front end part is tight and right so far!! Not bad 125k and only replace one tie rod end!!!!!! You don't know what your talking about!!! I bet your truck is a pos 4x2 not 4x4!!!!! Solid axles on trucks last a long time little boy!!!!!!!! You should of bought a real truck !!!!!😁

@rubenwong9574 5 жыл бұрын

You must drive only in highway grandpa and no towing or carrying over 1500lbs in the bed daily

@strikeforce4581 5 жыл бұрын

Everyone with lifted trucks and 12.5-14 wide running 80 get next to no milage. Lift after power

@BespokeCarpentry 3 жыл бұрын

Well, I have a 2016 chevy colorado 3.6l with a 3 in lift all the way around, with 12.5 wides and 33's, and I maybe lost about .5 miles to the gallon. I know on my 2012 2500 when I did the same thing it went from about 12 mpg to about 5 or 6, so I know what you mean for sure. Just depends.

@raamyasharahla535 3 жыл бұрын

I get a mile per damn gallon 😂🤦🏿

@losmoore3358 3 жыл бұрын

If I put a lift kit on my 2011 silverado , would I also need a leveling kit as well ?

@andrewwillig1826 3 жыл бұрын

Depends on the look you are wanting to go with...comes with take from the factory to look level with a trailer

@lililili4214 4 жыл бұрын

I'm running 20x12 -51 with a 2inch rc lower level block on my 2017 gmc sierra 1500 I have a crazy amount of pressure in the from end steering to the point the steering rack moves about an inch either way on a dry turn an basically floats around on the road extremely bad in the wind wondering if anyone else has experienced this an found out the issue alignment was done with factory tires 4 weeks ago

@huntertodd8010 5 жыл бұрын

Hard to find upgrades for the obs k1500s....

@CustomOffsetsTV 5 жыл бұрын

Depending on what year it is we have a few different upgrades for your vehicle on our website! customoffsets.com

@YoloVib3s 5 жыл бұрын

Hey Fuller I'm looking to upgrade my 2016 Ram 1500 from 17's to 20X10's -12 offset. I know I need a leveling kit & I'm looking at the Zone 2 Adventure series. I just want to know if this is good enough or should I also swap out shocks, etc? Very little off roading however I'm a landscaper and pull a trailer 90% of the time.

@CustomOffsetsTV 5 жыл бұрын

Fox Shocks would be a great upgrade for ride quality. -Fuller

@YoloVib3s 5 жыл бұрын

Custom Offsets so would the 2” Fox Coil over & Zone Upper Control Arm be a good combo?

@kanzzon 4 жыл бұрын

Wheel width has nothing to do with offset, 12 inch wide will not do damaged as spacers do. The weight in the other hand can seriously accelerate the wear on steering components. (this includes solid front axles as well). Thats the trade for being cool!

@TheCls63 4 жыл бұрын

So do positive offset affect the bearings too or is it only negative offset?

@CustomOffsetsTV 4 жыл бұрын

Changing it from factory specs can effect it!

@alexanderpabrezis9262 3 жыл бұрын

So how wide can I go on a Chevy silverado 1500 2020 without lifting it

@ErickGarcia-ns4yu 2 жыл бұрын

Just put 33 by 14.50 r22 on a new 3 inch level rough country on the front end and inside of tires wore out and mechanic says someone messed with the torsion keys when it’s been sitting still? Or does it normally do that by way of wear and tear? He also thinks it could be idler arm or ball joints? Driven maybe 7000 miles

@CustomOffsetsTV 2 жыл бұрын

It’s quite possible. But unlikely. Or worn out parts

@davidparks90 Жыл бұрын

What if I have a normal setup 20x12 hostile jigsaw their a -50 or 60 something and 35s but I also bought a 6 and a half inch super lift also I don't know if I'd have to change anything

@BEazyMann 4 жыл бұрын

My question is. Can I put a 20 inch wheels with -24 or -44 with a 35 tires without a lift kit on a stock 2017 ford Raptor

@CustomOffsetsTV 4 жыл бұрын

Check out these similar setups. It will say if there was trimming or rubbing. bit.ly/2vYAQvi

@forgivemylaughter Жыл бұрын

Thoughts 💭-12mm is that crazy? I don’t wanna ruin my paint. Is it considered a lot.

@SamSung-eb2ls 5 жыл бұрын

I just got a truck with 24x14 and it shakes while I drive any recommendations?

@CustomOffsetsTV 5 жыл бұрын

I would start by an alignment and if that doesnt take care of it check for any loose shafts or joints within the suspension/steering components

@tharealiztoneofone7827 4 жыл бұрын

Rotate your tires & get them balanced.

@SamSung-eb2ls 4 жыл бұрын

@@tharealiztoneofone7827 just talk to a tire shop . Said maybe my hubs going out. Gonna fix it soon.

@Sobriety5424 4 жыл бұрын

16” rims with big tires(33’s or 35’s) Classic country boy setup.

@valleylife88 3 жыл бұрын

15" lol

@waynes.2983 4 жыл бұрын

I just had a set of moog lower ball joints go bad in after only 2000 miles. Mostly dirt road miles but still...moog has lost quality from what I've seen.

@anonymouskids888 5 жыл бұрын

Added weight

@ryanvernon9473 5 жыл бұрын

How’s the best look for a 2017 Ford F-250 lift wise

@n1n0z24 5 жыл бұрын

Ryan Vernon depends how high you want to go you can fit 37s in a 4 inch lift

@ryanvernon9473 5 жыл бұрын

N1N0 Z I don’t want it to look like Larry the lobster because I hate that look big lift and tiny tires

@n1n0z24 5 жыл бұрын

Get a 8 inch lift and Try to get some 38x15.50x22

@n1n0z24 5 жыл бұрын

38s on a f250 looks great

@mar-mar5.438 Жыл бұрын

I shouldn’t have any issues with stock suspension on 20x10s ?

@CustomOffsetsTV Жыл бұрын

Depends fully on the application the wheels are going on and the tire as well.

@Patriotx-gx4ce 4 жыл бұрын

Starts @1:35

@NorCalMtnBiker86 2 жыл бұрын

200k subs naaahhhh.... Now you need to hit that 1 mill subs. You'll get there as this channel is fucking dope as fuck.

@charles17508 2 жыл бұрын

hkw much is shipping tires and rims and due you balnce them in your store .

@CustomOffsetsTV 2 жыл бұрын

Mount balance and shipping is free

@alligator_shart 5 жыл бұрын

i have a 06 expedition xlt 2 wheel drive and i found some 17x9 with a -12 offset wheels completely stock truck i was wondering if those would cause problems or if it would be fine

@CustomOffsetsTV 5 жыл бұрын

That size you usually wont see too big of an effect on the front end components, when you start getting into 12 and 14 wide wheels are typically when you'll start to notice it more often!

@Avi8CaLiBeR 5 жыл бұрын

What are traction bars!?

@73powerstroke56 5 жыл бұрын

Traction bars are used for trucks or cars with alot of torque. Keeps the wheel on the ground for better traction and prevents ur rear end from curling under ecceleration.

@CustomOffsetsTV 5 жыл бұрын

Helps prevent axle wrap !

@360VRStudios 2 жыл бұрын

Of course it was not design to have wide tires that offset 8 to 12 inches off side of the vehicle. You may need to beef up the suspension.

@shannonmcintyre1970 2 жыл бұрын

Yes

@Garcia1529 5 жыл бұрын

What's the wheel that truck has on the thumbnail?

@CustomOffsetsTV 5 жыл бұрын

Check out the full specs! www.customwheeloffset.com/wheel-offset-gallery/359669/2016-gmc-sierra-2500-hd-avant-garde-other-bds-suspension-suspension-lift-65in

@bernhard8540 5 жыл бұрын

Chevy front ends are pretty weak the tires like to point at each other often haha ;)

@CustomOffsetsTV 5 жыл бұрын

I believe thats called the "Katchow Mod"🤙😂

@tulerblank5137 4 жыл бұрын

So 22x12’s on 33’s would be fine?

@CustomOffsetsTV 4 жыл бұрын

Yes depending on your lift and what truck you have

@kevins2459 4 жыл бұрын

WhistlinDiesel: yes

@billybobjr2951 5 жыл бұрын

Anybody know who makes a nice kit for a obs powerstroke?

@-BC. 5 жыл бұрын

Solo motorsports

@lornesam2 2 жыл бұрын

I'm running 20x10 -24on a 6 inch lift

@rickredmond9511 5 жыл бұрын

With a sally IFS that cant handle anything larger than stock......YES

@BillieHQ 3 жыл бұрын

Basically what your saying is you gotta pay to play

@oldarkie3880 5 жыл бұрын

The manufacturers spend millions designing suspensions wide wheels just mess it up. I think tires sticking out of the wheel wells look dumb.

@knuckleuprambo 4 жыл бұрын

This brought to you buy the 15x10 35x15.5x15 mickey thonpson boie

@Dieselmd2008 2 жыл бұрын

Just remember modify = compromise

@privateowner1271 5 жыл бұрын

Need to talk about negative offset I mean the word offset is in the company’s name right 🤦🏽‍♂️

@JohnSmith-dj5gf 4 жыл бұрын

On my FJ40 we do the tall skinny....

@secondgone5066 4 жыл бұрын

i have 33x12.5x15 tire/rims i want my wheels to stick out like your. what rim set up do i need to make it happen?

@CustomOffsetsTV 4 жыл бұрын

SECOND&GONE Email us at info@customoffsets.com!