The flue getd hotter with elbows !! Strait up through the roof is best

I have just installed this exact system in my pole garage. I was amazed at how many obstacles I encountered while doing the project. First, after building the proper thimble box inside, n moving to the outside, that where the problems began. We installed the outer wall thimble mount, then proceeded to mount the pipe shelf bracket. (No overhang to work around, just straight shot up.) It's good we pre-fit these with the base 3 way pipe. We discovered, in order to get the 3 way into position, the shelf had to be loose from the wall. Those bolt were behind the outer wall thimble! So everything had to be loose n it was a royal bitch to tighten everything down. After that, we fit 2, 3' sections together. After locking into place, they were still able to pull away from other pipe. Next, we went to screw the upper pipe bracket fast to the top of shop. These holes were not big enough to accommodate the fasteners we had to use to withstand the wind we get here. Lastly, the chimney cap that just snaps into place, would have blown off the 1st wind storm we got. So, we re-enforced all connected pipe with self tapping screws. And the chimney cap, we installed 1" spacers with self tapping screws. Still not sure it will withstand the wind we get here. Make sure you are not planning on a breeze install. If you want it done right, you need to know what you are doing, and the way this stuff goes together is not what it seems. There was more work involved than people make it out to be. I might be petty, but this deals with fire, so proceed with caution.

I love this video they're fixing to tear a big barn across the Road from me thank you very very much I love the outcome it's absolutely beautiful and the product information is very good thank you so much😊

Glad you pointed out the pipe needed another section still. Should be 2 feet above any roof point within 10 feet of the penrtration, if I recall.

Thanks brother, I appreciate it. That was my exact situation, pulling out the old 80’s wood burning stove from my fireplace and reusing it in my garage.

Finally! A good vid on this install!

Thanks, I have to install one in my cinder block garage asap. It really helps to visualize it going up, thanks

Great video!! Liked and subscribed!! Getting ready to do this in our 40x30 shop we just finished out! Thanks for the detailed video. Super helpful!!

Man love your channel. You keep it so simple and you explain it well. Thank you keep up the great work. Happy Nee Year

Proper job guys! Thanks, from England!

Great video! We'll be purchasing this kit in the near future. Thank you for uploading this video.

Best video I’ve seen!! Thank you

Thank you for posting your install. Very much!! Dealing with issues with our installer. Figured from day one I'd be installing it myself but good grief. Our soffets do stick out on all for sides of dwelling more than yours do. Hoping I can figure this out and safely as that is all that counts. You did excellently. Appreciate your sharing!

IAM doing a 8 inch stove pipe Thur the wall just because I have had a few roof leaks in the past

Awesome video - that is what I was looking for.

This is so awesome! I'm interested in installing one of these in my home. It seems like the most economical, natural and comfortable kind of heat source that exists. Just need to figure out how to tie it in to the in-place ventilation system to spread the heat around...

Very cool! Especially so because that's MY Buck Stove. It was here when I moved in in 1990. 33+ years of use & no problems. It'll cook u right out of the house. Only difference i see is your's is free-standing & mine was installed as an insert in the original fureplace (home built in 1951). Not sure if yours has the 2 speed fan. If so, you're gonna love it.

Very nice, thanks for posting... I have the same stove. To make it cheaper and easier, I'm just going to put my stove outside on the deck and blow the warm air indoors...

Looks good . I need to get my stove installed at some point. I would recommend installing a simple damper in the stove pipe . It will help control the draft and heat loss .

Love your hat! 👍🏻

Good job

very informative , thank you !!

Through the roof is a way better option. Better draft more single wall which means more heat easier to clean and cheaper option.

Good job but should consider flue shouldn’t be 90 degrees bend and where is fresh air intake for fire triangle ❤

Thanks! very nice video

Great video. I am planning on an installation in my shop very similar. This helped allot.

Hello thank you so much for showing this I need to know if this works on a wooden building and it's not as big as your shop the shop I have has concrete floors but it is wooden built any information you can give me I would be greatly thankful for and thank you again because I have shingles on the top also I have All wood with LP siding on top of plywood of course any help again would be greatly appreciated😊

Love your channel, awesome content! I’m about to install a wood stove in my metal building and was going to use the same kit you used. What did you use to attach the duravent kit to your single wall pipe coming off the stove?

Thank you for doing this video! I need to do the same with my woodstove setup, and you answered a lot of questions I had. I was really pulling my hair out trying to figure the best, and safest way to go through the wall. You are a God-send!

Glue a stick onto that dimple in the metal and pull it out, then scrape off the glue.

Looks great I want one but I don’t know if I could pull this off as not very diy minded. Really want one though . I think it’s crazy money to have a proffesional in to do, perhaps there is a middle ground, someone skilled enough who I could pay.

If you don’t mind me asking? I’m installing the same kit with a 24” pipe. It’ll put the platform out about 26”. What size and gauge slotted angle iron did you use? I’m thinking I’ll need at least 36” lengths going out to support the weight. Any suggestions?

Verry nice, you do have a long flue pipe inside so all should be well, but in general two 45's are better than one 90.

I watched your video because I was a little worried about the situation you ran into clearing the roof overhang soffit. About how far does your shop roof come out from your outside wall? I'm pretty sure I'll be ok because you had to go through alot more wall material.

Great video! When you installed the Clean Out Tee through the outside wall thimble... Did you use a cauking between the Tee and the Circular hole of the thimble? (to fill the small gap) Much Thanks!!

Good looking install. If you don't mind my asking, why did you set the stove right on the floor instead of elevated a bit? I know if that was originally a fireplace insert it wouldn't have legs. We bought a farm where everything was heated with wood. The older gentleman who owned it elevated all of his stoves to waist level. It was great. No bending down to the floor to load, tend, or clean. I know that was a little extreme, but it sure was nice. You're not young forever.

Great video, thanks! I am looking to do almost the same setup but probably going 15 feet higher. Does anyone have a good resource for what angles and vertical rise is acceptable for stove chimneys? I had assumed that having a 90° bend was not to code...maybe I am wrong. Also, there must be some limit on vertical rise. Any help would be appreciated.

Do you have a link for the black pipe? Does the kit come with this black inside pipe?

Is there not a code for a specific distance above roof line the cap needs to be? Or, since this building being metal does it not matter? nvm, he answered it right around 6:30

Is that a buck stove? I have a 26000 being used as a fireplace insert rn. I have a Wonderluxe wood circulator for my primary wood heat. But I love my buck stove. We use it every day. And man does it push some heat. Replacement parts are expensive but definitely worth the money. Looks terrific too

Love your video! Just started following your channel. I’d like to ask why did you go through the wall versus the roof? My wife and I just started making KZfaq videos (Off-Grid on Friday) to chronicle our journey on developing our property. I am hoping to have similar success with my project. Any info on why you went through the wall would be great. Thank you!

How did you attach the rectangular part to the stove with those screws? I have the same part for my stove that just came in. Thanks for your help!

How many feet off the ground to be leagal (Gas fumes)

I was shocked to find that stainless insulated duravent costs $80/ft

Good video. When going through the wall with single wall pipe did you use the adapter the kit came with? My kit the adapter is loose on the triple wall side. Just doesn't seem right or am I too paranoid?

Any issues with the 6 inch pipe? I have a near identical buck stove with the same rectangular 8inch connection. I ran it for a winter with 6 inch pipe (like your set-up) with no issues. im wondering if this is a good idea or not?

Did your single wall just connect to the duravent double wall or did you have to get adapter for it ? I am trying to figure out how to install the non duravent single wall to the duravent double wall. Any advise would be much appreciated 👍

I am thinking about going through and existing basement window for a stove downstairs. Any suggestions about how to go about it?

Can I do that in a mobile home?

What type of pipe goes through the wall and how? Does it connect to the black pipe? Is it a bracket? How thick of a wall could I use this on?

❤

How did u create the hearth with pavers? Do they need to b grouted, or can u just lay them next to each other?

how is this working out combined with the insulation? I have a monster wood stove in my 30x30 and it does very little to heat the shop

you should make large roing fire than pack full large logs for hot long burn no pine

How high does the pipe have to go up inside before you can do a 90 degree angle out the wall?

How is that wall thimble holding up? I’m doing a wood stove but am apprehensive about the thimble not having enough space between combustibles.

I have exactly the same as you installed how did it work out with going to 6" from the 8" stack?

Where do you find the bracket material to extend the pipe out? Thanks!

What bout existing wall studs? Are you cutting the hole in between studs?

Where did you get the angle iron? I have to do something similar.

I have the same stove need that rectangle part on top don’t see the link for it thanks

What that in the corner of your shop black barrel ?

You dented the base tee, ooops

Was there any issues with reducing from 8 in to 6 in?

Whats the difference between the $299.99 "DuraPlus 6 in. Diameter Chimney Pipe, 36 in., 6DP-36CF" And the $139.99 "DuraVent DuraPlus 36 in. Triple-Wall Stainless Steel Chimney Pipe, 6DP-36SS" What's the "cf" and "ss"? Then maybe il know which I need.

"I installed fireproof rockboard then put a piece of flammable wood behind it." 😆 "Then I sealed it with fireproof spray foam." 😂 Rockwood is your friend, son. Utilize it!

I noticed right away it's not high enough.

Is the flue tee piece made from foil

What is the rough opening through the wall for the kit?

Looks great however idk why these manufacturers don’t tell you that the crimp should go up with the direction of the air flow. So many videos I’ve seen with people installing the small end in the wrong direction. I’ve been doing HVAC for over 25+ years and it makes me cringe when I see people install chimney and dryer vents like this.

wheres the fire test?

Any issues going 8 to 6 inch?

I've honestly always been a little skeptical about installing through a wall, can anyone tell me how the draft works through the wall versus through the ceiling/roof? Or is it all 6 to 1 ---- half to the other.

Hmm. Didn't know concrete could catch on fire? What are the pavers made out of, not concrete!?

After a year, how do ya like it??

This fire pit is one of a few covered pits that is on the list kzfaq.infoUgkxAU9pOCSV9Y5JprooHvfxTpOrt4hx8uRM of approved products for Disney Fort Wilderness. The product served its purpose well and provided excellent fires throughout the evening. We were able to open the door and do s'mores, but I had to be careful because the handle was a bit hot on occasions. Additionally, I wish they had replaced some of the standard nuts with lock nuts in some places. We lost the door handle after just a couple of days of usage. Not a deal breaker, just a recommendation. I still give it 5 stars.

Link for the adapter

Where is your damper?

sorry no thumbs up for you @PatriotDIY that vintage woodstove requires 48" clearance all around its body as per Code Compliance The rear cement board does not constitute a clearance reducing shield if you do not have air movement all around and when you installed the wood cross braces yuo negated the air flow vertically and put a combustible material behind the cement board which will transfer heat. this means the rear wall shield MUST be a minimum of 3" off the floor and 3" off the ceiling [north south flow]and be also mounted 1" off the wall to allow for east west airflow and the shield requires to be 18 - 20" wider than the stove on both sides READ YOUR NFPA211 section 13.6 and the chimney must be a minimum of 36" above the roof surface to be code compliant !!!!! And did you put in three screws per single wall joint and install and expansion joint???

thaaaaaattt dent....

I agree with JBiz180, a better more efficient install would have been straight through the roof. That stove pipe and chimney system is undersized for that stove and will not work optimally, and might smoke when you open the doors. That stove is a dinosaur and very inefficient, you will be going through a significantly more wood than if you had one that was built in the last decade. Also its too short, the chimney doesn't meet the 3-2-10 rule as described in the IRC. Nice install otherwise. I do like the bracket.

Well your lucky. This is illegal in my county. It had to go through the roof.

Music too loud

You really should not have the horizontal piece at the top going through the wall………that should be a vertical angle….that would be illegal in this country..

It's too short.....

You really should be saying "farther" instead of "further" when you're referring to distance.

you need less music and more detail on putting the pipe in

Having am air space with out air circulating behind it is not code the horzontal strip stops that . Also that is a fireplace insert which is ment to be in a fireproof box. The opening is at ground level which is where gas fumes are at least you should raise it on blocks to be somewhat safe. Try reading before some install instructions before you teach how to to burn peoples homes down.

Your chimney isn't tall enough. You need to be 4' - 6ft higher than the highest point/peak of the roof. Otherwise a strong wind will effect your draft adversely.

You damaged/ dented the shinny pipe. Makes install look like crap

You tubers, please turn your music level lower than your voice, it's gets annoying when the music is too loud.

thats gunna burn ur house down

I had to abandon this video early because of the nerve grating music. Too bad he used such annoying music because it looked like it could be a really informative video. I would change the music or leave it off altogether for a less jangling experience to your viewers.