wood turning a new craft show project

Рет қаралды 16,501

4 ай бұрын

A new product added to my craft show. This woodturning video is a new woodturning project I will be adding to my craft show booth. I used cherry tree branches for this wood turning project. It is a mortar and pestle. It takes about 20 minutes to make. I added burn lines to add some details. Both items are sanded to 400 grit and finished with friction polish. Although I'm thinking just using a food safe finishing oil might be better.
I hope you enjoy the video!
Thanks for watching!
#woodworking #how #howto
/ rcwoodturning
rc_woodturning?...
Affiliate links
Affordable tool links below.
As an Amazon affiliate I make a small commission if you make a purchase thru these links. It doesn't cost you anymore and it helps fund my youtube channel. I thank you in advance.
Chucks
amzn.to/46seEpL
3.75 chuck
amzn.to/3ttQ8Gb
3.75 shark jaws
amzn.to/3ttQ8Gb
2.75 chuck
amzn.to/48R6k4I
2.75 shark jaws
amzn.to/48R6k4I
Turning tools
Starter sets
amzn.to/46bUO26
amzn.to/3ruDbv8
Roughing gouge
amzn.to/3PFPPAY
Bedan
amzn.to/3ZjeUov
Skew
amzn.to/45OtmqZ
1/2 bowl gouge
amzn.to/48c27rT
Diamond parting tool
amzn.to/3PCy7hD
affordable lathes
amzn.to/3bZB7mP
amzn.to/3auEZM2
amzn.to/3PeJTvF
amzn.to/3NSKYYG
hollowing tools
amzn.to/3yOIbLQ
amzn.to/3akX3Z0
amzn.to/3uzIyHU
amzn.to/3ap6fvE
woodturning tools
amzn.to/3RiloPW
amzn.to/3yNLh2H
amzn.to/3Pf8ccz
amzn.to/3uxZpL8
affordable chucks
amzn.to/3NL9oUd
amzn.to/3NL9oUd
amzn.to/3AySLYF
amzn.to/3yOJ0nU

Пікірлер: 48

@TramJizzle 24 күн бұрын

Another episode of why didn't I think of that. Beautiful result ! 👍👍

@RcWoodturning 24 күн бұрын

@@TramJizzle Thank you!

@alonzovillarreal4666 2 ай бұрын

Nice!! I’ve wanted to learn how to do this my entire life.

@RcWoodturning 2 ай бұрын

There's no time like the present. Thanks for watching!

@DougMilleratWoodSpunRound 4 ай бұрын

Great project. I need to make one for home and several to sell. Well done buddy!

@RcWoodturning 4 ай бұрын

Thank you Doug! That's the first one I've turned. I'll be making several for my craft booth. Thanks for watching!

@user-kf5of8pq9p 4 ай бұрын

Nice mortar and pastel, Rus. That grain is really nice also. Thanks for the idea....Dan

@RcWoodturning 4 ай бұрын

Thanks Dan! Trying to expand my ideas.

@applevalleyguy404 2 ай бұрын

I assume that wood is still green. How do you keep it from cracking after it dries? What type of wood is it?

@RcWoodturning 2 ай бұрын

This wood is cherry. It isn't green, but was wet from rain. I use a bag filled with wood shavings to put the project in. That slows down the drying to prevent cracks.

@lyndaowen2154 4 ай бұрын

very cute -- I like it

@RcWoodturning 4 ай бұрын

Thank you Lynda! I appreciate you watching!

@knothead5 13 күн бұрын

Been "addicted" to your videos, using limbs and twigs. Never saw a Jacobs chuck with the spur in the chuck which is in the headstock? Why do you do this?

@RcWoodturning 13 күн бұрын

@@knothead5 I'm experimenting with ways to hold the spur drive without removing the chuck. It's a work in progress. Thanks for watching! I appreciate it!

@omm2745 4 ай бұрын

Very nice. You must have great access to wood.

@RcWoodturning 4 ай бұрын

Thank you! I just grab wood where ever I can find it. Lots of forest area around here. Thanks for watching!

@knothead5 13 күн бұрын

Construction sites are a good place. Not far, there was a wooded area of about two acres that was cleared of all trees. Chipped and burned. Even had a blower system on a gas engine to inject air into the fire.

@knothead5 7 күн бұрын

Many woodturners have FOG wood= found on ground. Some beautiful wood turnings have started as firewood.

@indianatone218 4 ай бұрын

Lovely Job i wondered where you were going with this one .

@RcWoodturning 4 ай бұрын

Thank you! Always appreciate you watching!

@tonyzola9396 4 ай бұрын

Very nice love your videos

@RcWoodturning 4 ай бұрын

Thank you Tony! I appreciate you watching!

@tonyzola9396 4 ай бұрын

@@RcWoodturning no problem I get a lot of ideas from you keep putting videos out you have a lot of great ideas

@RcWoodturning 4 ай бұрын

@@tonyzola9396Thanks! I'll do my best

@dregag4415 4 ай бұрын

I see that you're not using your yellow harbor freight lathe! Which one is this? Again, huge thanks for your videos. I did learn a lot from your videos! - I like your little yellow sander!

@RcWoodturning 4 ай бұрын

Thank you! I still have the yellow one. This one is a shop fox. The shop fox is much quieter. That's the main reason I'm using it. I got the sander from Amazon. It's a foam palm sander. 2 inch diameter. Thank you for watching!

@noelgreen9381 4 ай бұрын

Yes, food safe finish would be better. Friction polish will come off in the items being ground with first use. Don’t ask how I know this! I now use walnut oil. Takes a long time to cure, but food safe.

@RcWoodturning 4 ай бұрын

Ya I thought about it after I finished it. I'll just sand it again and use oil. I haven't tried walnut oil and been wanting to. So this will be my chance.

@jbarrow8081 Ай бұрын

Do you have a link for the "worm" insert you use with your chuck?

@RcWoodturning Ай бұрын

I don't have a link to just the worm screw. It came with a chuck I bought.

@raydriver7300 4 ай бұрын

That’s lovely. I do like to watch the delicate work you do with the gouge and skew chisel. I have mentioned it before but do you follow left handed turner Jim Sprague of Sprague Woodturning working outboard on his lathe with reverse threads? Keep up the good work 🌞

@RcWoodturning 4 ай бұрын

Thanks Ray! Ya, I know of his channel but I don't watch you tube very much.

@raydriver7300 4 ай бұрын

@@RcWoodturning And I watch too much KZfaq and wonder why I get little done 🌞

@martingayle5376 4 ай бұрын

Nice one. Where did you get that screw-chuck insert? I've never seen one of those before.

@RcWoodturning 4 ай бұрын

Thanks Martin! It came with the black wen chuck that I got.

@AlbeTurner 4 ай бұрын

I was curious about that as well.

@Richard-ky9lf 4 ай бұрын

Hi. As a new turner I can not visually identify the tools you use. Will you please name them? Thanks. I enjoy your videos very much. You are an inspiration.

@RcWoodturning 4 ай бұрын

Thank you Richard! I appreciate that! This video explains the tools I use. kzfaq.info/get/bejne/mdSFh5Og3rC7dJ8.html

@Richard-ky9lf 4 ай бұрын

Thank you. Going there now.

@Mr.Peabody961 4 ай бұрын

Why was there smoke coming off of the inside cuts while you were hollowing out the bowl? I’ve never seen that happen before.

@RcWoodturning 4 ай бұрын

The wood was wet from rain. That was steam created from heat off the tool.

@Mr.Peabody961 4 ай бұрын

@@RcWoodturning thanks….. had me wondering :)

@bobboyer9440 4 ай бұрын

Out of curiosity, how much would one get for these at a craft show?

@RcWoodturning 4 ай бұрын

I look at things differently. I'm not in for a lot of profit. I would sell it for around 10 bucks but you can probably get more.

@garyhead577 4 ай бұрын

I'm wondering why you don't sand?

@RcWoodturning 4 ай бұрын

I usually don't show a lot of it on camara. People find it boring. I sand everything from 80 to 400 grit. Unless I use a skew. Then I will start with 150 or 180 grit.