Nobody has ever returned to complain about the compressor blowing up.

THANK YOU for making the video. It makes me appreciative of OSHA standards and SAFETY RULES. No hand protection, no spotting shields, No leathers. No safety boots. Nobody wire-wheeling the surfaces BEFORE rolling, since the inside of that tank has been subjected to a life of Salt-Water, and hasn't been cleaned up before assembly. I FELT for that guy, bending over while welding that long side seam. His back is going to be hamburger meat before he's 40! At this rate, he'll be blind in no time. Not a pair of Safety Glasses in the shop! LOTS OF TALENT, NO safety. There's one thing...he knows how to weld! THANK YOU, again, for your video. This video should be adopted by OSHA, and be played before every safety workshop course OSHA does, as a PERFECT EXAMPLE of what NOT to do. I'm going to send this link, to the welding/certification instructor, for the state; to start every course off with. Bill from Tn. 🇺🇸

This is nothing to do with scrapping ships. But this is like watching a well made horror movie: half the time you're admiring how it's done and the other half you're absolutely bloody terrified. I wouldn't rely on that tank to hold water, let alone anything else, and I wouldn't rely on that guy to drive me anywhere since he'll be half blind from welding with no safety glasses.🤯

Amazing how they turned 15mm hull plates into 2mm sheet metal using basic tools.

Great, so your air compressor comes preloaded with a bunch of dirt and soil and paint chips and who knows what else inside of it.

Safety sandals? Check. Safety squint? Check. Excellent, you’ve got the job.

Did I miss the bit where the pressure testing Tag was put on after the cylinder was pressure tested? I once went to a small workshop where a 10 CFM compressor had its tank rupture as it approached cut off pressure. Fortunately no one was in the the area at the time but the shockwave broke every window in a care nearby and the plaster and timber wall next to it had a very large hole through it. The compressor head hit the roof and punched a hole in it and the electric motor hit the car nearby and didted the door so the outer panel was touching the inner panel. There were bits of metal imbedded in walls and other wooden structures. If you were in that area of the shed then you were probably dead or critically injured.

There is nothing to say that hasn't already been said. Good luck and prayers to all involved with these tanks.

10 points for the safety squint and a bonus for the steel toed sneakers.

I like how they didn't clean one spot before welding. I guess all that dirt, rust and paint won't effect the welds..🤔

Working in a shed with that receiver up at 120 psi would be like sleeping with the reaper.

Maypop Compressor. Don't worry, Allah will protect you. 😅

Love the safety equipment these boys use!

I still can't keep trying to flip my hood down😂

The guy is a really good welder. They should clean the metal before sealing it up inside the tank. The guillotine is impressive. I want one.

It's a good thing they are wearing their safety flip flops

Always love the traditional garb with a baseball cap and running shoes. You drop one of those plates on that shoe and learn what severance pay really means.

For ingenuity in making do with what they've got, 10/10 This workshop could not afford the safety equipment and processes we take for granted and even if they got it, they would need to hike their prices. That would drive away similarly cash-strapped customers. Kudos to these workmen for allowing their operation to be shown on the Net, warts and all.

Please make a new ship from old compressor but clean metal first before welding and position an extraction fan to remove fumes !

they weld through dirt. its unbelievable. and bare feet as well.

It amazes me that so much manual work takes place within these factories yet with no one seemingly willing to invest in a simple concrete slab to lift production up out of the dirt.

I just can't imagine wearing sandals doing that work

Great video 😎Health and safety at it's finest 😬

Being a welder- metal fabricator I must say this is very impressive. Tip of the hat.

Good job.

Where is the welder ground clamp? Is it just stuck in the earth near the welding area?

The measuring tools used in this fabrication job were amazing!

Compressor market is Booming!

Good to see they are doing everything up to OSHA standards.

Next time you see a bargain priced air compressor at Harbour Freight … think twice before buying one.

This is good when you want your pressure tank pre rusted on the inside, made of scrap with overlap joints for the domes making them even more prone to corrosion. I mean, what could go wrong?

Think Homeslice holds an R Stamp? Also, putting that overlapped seam on the bottom of the tank is a bad idea.

Perhaps the seam would be safer if it was in the upper part of the tank? Great work reusing the steel! 👏👏👏

Bless their tenacity! ... Gettin 'er done.

Que GENIOSSSS !!!! Saludos

Interesting and scary, all at the same time.

Este material es de muy buena calidad , acero naval tiene propiedades superiores al usado para fabricar tanques de compresores , saludos desde Argentina 👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻🇦🇷🇦🇷🇦🇷

Fascinating Captain

they are making there first spaceship!!

I personally don't want to be anywhere near these pneumatical boom booms.

Good job but why you didn't clean and paint the plate from inside before closing and welding coz you are working on used material

No mask or goggles when welding the triangular things. Crazy.

He took a piece of scrap and made another piece of scrap out of it

Things like this are incredible , these people take a retired shipping vessel and turn the steel into something else....so cool how people come up with ways to reuse something , never would think of cutting up a ship and turning it's steel into thoughts of air compressors.

Eyeballing it baby!!!!

Guaranteed up to 20 psi and comes pre-rusted inside.

No gloves. Insane.

This is Masterpiece.

The best thing by far recycling , awesome job.

I normally respect these guys but pressure vessels? I give it 50-50 on the ultrasound but O don't think you are going to get it past the Hartford guy.

This is the OceanGate factory where the Titan sub was made.

Well done lads a grand job...Tom in Scotland.

Is that tank going to pass a hydro test of 1.5 times that of its rated pressure capacity?

Hmmm, could these guys make me a submersible? I have some wealthy patrons that want to go underwater sightseeing and there's been a recent opening in the market. Now where'd I put that Atari 2600 joystick?

This is a perfect example of why they can produce products cheaper than can be done in the USA, no safety regulations.

Be thankful of your $20 hour job in the USA.

Was waiting for them to test for leaks.

I see absolutely no serious accidents where apparently safety shoes have yet to be invented.

It looks like all metal working of any kind in Pakistan is done on dirt floors, either inside a building or outside of it. A book describing their efforts could be titled, "Working In The Dirt."

And everyone wears Flip Flops, not a high viz in sight. 😃

that would make a sensational wood stove!

I do not want to get anywhere near that tank when it is under pressure.

Each of our compressor tanks are crafted by skilled tradesmen, to bespoke requirements, no two are the same making them as individual as our customers.....

These guys are pretty amazing IMHO .

Oh my God! Back to the dark ages.

Got to give them 'A' for effort and ingenuity! Noticed that absolutely nothing is cleaned while assembling or while welding. No precision alignment of base stand or top plates. Of course, no concern for safety. Where is the ASME Code Certification label? I am sure these fellows work hard. I wish them well. Too bad the video is cut short and does not show the finished product.

Respect !

No proper shoes (or boots), no gloves, no glasses, no mask or respirator, no safety at all. The blood lead level of these welders must be extremely high. Totally insane!

thats crafsmanship

I wouldn't put more than 2 psi in that thing. I'm horrified that they are allowed to sell those bombs.

Not a bad welder that dude

LOVE THIS CHANNEL WE APPRECIATE YOU AND YOUR HARD WORK!!!!!!

Only the finest masters of their craft are allowed to work in pyjamas and flip flops

Ka Boom

I sea and see.. My eyes are always watching 😂

These films NEVER fail to impress. Here, in the UK, approaching a metal cutting machine like that shown.....you'd be wearing protection deemed safe to handle unrefined plutonium!!!! Not these fellas. Sandals, cotton shirts and some kind of head covering, that'll do! Is this how they built the ocean gate sub, Titan I wonder?

Maximum allowable pressure: 5 psi

Something doesn't add up. The cost of oxy acetylene exceeds the steel recovered.

интересно сие творение будет проходить аттестацию? Будет ли выдан паспорт сосуду под давлением?

Gloves, eye protection, steel toes, we don’t need none of that 😂

Nope, I wouldnt bring that tank up to 150psi. I like my legs and arms right where they are, attached to my torso, not lying on the workshop floor.

I’m guessing there’s a lot of men missing toes in that country. 🤔☮️🦆

nothing like working on a dirt floor then welding dirty rusty metal.

Looks like the flip flops have gone 😂

Sorry, I welded on oil tankers in for repairs, there's no steel that thin on the things. That said, it's a nice job they're doing with the tools they have.

These foreign industrial videos creep me out. Not a steel toe shoe for miles.

I knew for years you never weld a pressure vessel but only recently came to understand how dangerous 100 psi in a 10 gal tank that failed can be. Please look this up on youtube. AVE, and Diesel Creak and others and myself do dangerous things safely many times to get a job done when you are the only guy on the job. Once you see how bad a pressure vessel failure is it will make you rethink using an old air tank Like the 50 year old farm all american made one in next room that is 50 years old.......I am no safe police but using old scrap steel and making a pressure vessel is really bad. The way these skilled poor bastards work with no PPE is one thing but they are building stuff that can Kill and maim more than just themselves ......this things are time bombs just waiting for someone.......I did love this VJO all the same!

interesting. *WISH THEY HAD CHIP MONK.. TRANSLATION FILTER IN PLACE,!!!🤣🤣

think of buying what you think of as a new air pressure chamber ...only to have it blow up!

Real men wear sandals and don’t let safety get in their way!!!

Awesome but Safety is not there 🤷

It seems like everything about the way these compressors are put together is asking for trouble. Maybe not a blow up, but seams failing wouldn't surprise me at all. Welding painted and dirty metal doesn't seem to faze these guys at all. I sure hope these aren't exported

That was cool

When was the last time your front load service last.

Ma Sha Allah. Hard working Pakistani are pride of my country.

I said this once before, " this is like watching a snuff film you know it is all wrong but you keep watching it anyway"

same company who made the Titan for Oceangate ?

👍✅🎉काश.... भारत और पाकिस्तान एक देश होता तो दुनिया हमारे टैलेंटेड कारीगरों की अदभुत क्षमता देखकर हैरान हो जातीं

So Mohammed... Do you have ANY engineering calculations that show the material is suitable? ANY pressure test data? Hmmm. Didn't think so.

Did anyone notice the sheet metal not cleaned? A permanent source of contaminants INSIDE the welded up vessel. AND, very unsafe welding for a pressure container.