Hey Guys, Here is a free way to remove the Exup servo motor on your wr250r
Пікірлер: 32
@chrisu906 жыл бұрын
Worked for me. Thanks bro you saved me 50 bucks 💪🏻
@victorbondar952 жыл бұрын
Just did this today, worked great. Thanks for sharing!
@whoscook44814 жыл бұрын
Thanks for the video. Another satisfied customer.
@danielbarry58625 жыл бұрын
How do you get the resistor out of the cover. Please help
@Pablo_Coach5 жыл бұрын
Important question: When the ignition key is in the 'ON' position and the engine is not running for a period of time greater than 12 seconds. error code 17 do not will display?
@coletrickle1776 Жыл бұрын
Thank you! Worked on my 12 WR
@MultiFab144 жыл бұрын
Thanks mate, saved me $100 AUD
@fraserb6096 жыл бұрын
Cheers mate worked perfectly for me.
@Melbournerider6 жыл бұрын
Fraser Barrons Barrons that’s awesome!!
@donlewis59904 жыл бұрын
Hi Thanks just done your mod 😀🍺
@JamesM0M2 жыл бұрын
So i did this, it worked…. Heat shrunk it, turned back on. Threw the code…cut it open, somehow popped off. Resoldered again, now its throwing the code still. Any ideas? Anyway to reset the bike somehow? Or do i jus need to order the graves resistor?
@mikemurray22986 жыл бұрын
Love the australian accent. Wished I lived there or in England, the further out the stronger the accent. Would love to live in rural England
@subparadventures28766 жыл бұрын
Mike Murray he sounds like a kiwi mate
@TapioBlue5 жыл бұрын
Sounds Austrian to me, he should put another shrimp on the barbe!
@JoeJoeMoto6 жыл бұрын
I can't remember doing any of that when I did my WR250R exhaust.... I think I just linked two pins together or something.
@Melbournerider6 жыл бұрын
JoeJoe Moto haha I dunno why this was works but it does for me haha
@katsugi1836 жыл бұрын
Very nice tutorial ❤
@perryatkinson6 жыл бұрын
I just did this too. How did you go about making the thing waterproof? I am considering putting it back inside the plastic housing so the connector seals properly.
@rezalzainal85273 жыл бұрын
Same servo exhaust yamaha r6 sir?
@blooskyy74 жыл бұрын
I tried this mod and initially it seemed to work, but after a few minutes error 17 reappeared with the engine light on and I haven't been able to fix it. Has anyone perhaps experience this too?
@donpetryna43563 жыл бұрын
Yep same. Going to try plugging OEM servo back in to see if clears, also have eliminator now but still wont clear. If not, contacted local shop and said they may be able to clear using Yamaha diagnostic
@toddwmac6 жыл бұрын
Hey Melbourn...thanks for the tip. One question. Can I yank the EXUP and pull the lines from the pipe and leave the valve in place? In other words, does the valve stay open when the lines are pulled (I'm waiting on a new pipe)
@Melbournerider6 жыл бұрын
Todd MacDonald I believe it stays open as the spring forces it open
@Pablo_Coach5 жыл бұрын
The white flat plug (resistor 7,5k) on which the soldering is done is in the exup device or you need to buy it?
@Melbournerider5 жыл бұрын
Paweł Przybyło it’s on the exup
@Pablo_Coach5 жыл бұрын
@@Melbournerider thanks for answering my question. What mileage did motorcycle ride after making this modification?
@Melbournerider5 жыл бұрын
Paweł Przybyło it’s always been good on fuel consumption, no loss.
@Pablo_Coach5 жыл бұрын
@@Melbournerider I'm sorry for my English, you've misplaced me. In my question I meant total mileage of the motorcycle after this EXUP plug modification.
@SeeItWithSimon6 жыл бұрын
Blow torch? LOL you're nuts. Heat gun is fine.
@gob93336 жыл бұрын
dab
@250ExplorerVideos6 жыл бұрын
Just did this today, worked great. Thanks for sharing!