WV Caddy ABS/ESP MK60EC1 unit coding/programming after replacing...

No video

WV Caddy ABS/ESP MK60EC1 unit coding/programming after replacing...

Рет қаралды 72,433

Күн бұрын

Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
This Caddy came to me after the ABS unit was replaced, and needed coding/programming...
On the module errors 00003, 01042, 00778...
Follow me on this video to find out what was the problem and how to resolve it.
Hope you enjoy the video.
Any questions or comments put them below.
Like always, thank you for watching!

Пікірлер: 193

@victormihnea7176 6 ай бұрын

I was able to successfully replace the ABS Pump on my 2012 VW Jeeta with the help of this post. I used the Foxwell NT1009 scanner. Thank you!!

@LMAutoRepairs 6 ай бұрын

☺️ That's great! Thank you for watching and for your comment! 👍👍👍

@itridz5860 3 ай бұрын

@@LMAutoRepairs hi friend How much time did it takes Because I've the same problem on 2012 caddy and I was pressing for more than 2 hours at the end an error came up so now I'm suspecting a faulty abs module The only DTC is 00003 calibration not So what do you think ?

@LMAutoRepairs 3 ай бұрын

The procedure takes a bit, but not 2 hours... 👍👍👍

@aleksistar631 2 ай бұрын

Many thanks for this video. I am currently working on an engine swap in a golf 6. The new engine is different in size than the previous engine. Got all the electronics including ecu, ignition barrel, keys and cluster instrument for the new engine. But I've told that the abs module will need coding

@salehalghamdi2284 2 ай бұрын

I got the same problem and it was solved with the video I put here. But the cruise control is no longer working, and there's also a problem with the air conditioning.

@LMAutoRepairs 2 ай бұрын

That will be most likely unrelated... Was the ABS unit also replaced?

@markobezjak6952 3 жыл бұрын

Perfect succses. 👍 If you know what you are doing. I use guided functions to do those kind of things. I dont know which channel do what. Or I simply turn on the odis and he will do the job for me, or he will telling me what to do. Thank you for the video Luis, it was great.👍

@LMAutoRepairs 3 жыл бұрын

😊 Thanks... for watching and for your comment!

@jasonga Жыл бұрын

With the mk70 you got to change wires on abs thing Update, No do not touch wiring, you Must make sure you change the other numbers below the coding number, it should be copied from old speedo, do that and its fine!!

@Ianf1x 3 жыл бұрын

I have same vw and when ever you remove the battery the car needs to be driven and the lights reset . After repairing fault . I did it the same as you First time after fitting front fogs with vcds took me 4 hours then found out only need to drive car . Great vid as usual 😎

@LMAutoRepairs 3 жыл бұрын

👍👍👍

@denisivanovs5465 3 жыл бұрын

Famous Abs implausible operation fault code, it becomes a bigger problem now, getting difficult to sourse second hand parts for a reasonable price, even if you find one, it has a chanse of failing soon, because is a very common problem on these types of Abs control units.

@LMAutoRepairs 3 жыл бұрын

👍👍👍 Thank you for watching and for your comment!

@cristo844 3 жыл бұрын

Install revision BL or BJ and add 00 to the original coding and the problem of failing abs units it's solved!

@LMAutoRepairs 3 жыл бұрын

Video coming for that...😉 👍👍👍

@denisivanovs5465 3 жыл бұрын

@@cristo844 so the coding for the BL and BJ is longer, and I need to add 00 in the end? Problematic original part numbers are AD and AE

@LMAutoRepairs 3 жыл бұрын

Pretty much yes...

@va7052 3 жыл бұрын

Nice to see you working on .....like my brands of cars.Nice job right there.Still learning from you Luis.

@LMAutoRepairs 3 жыл бұрын

😊 Thanks Alex! 👍👍👍

@billytremoloband7456 2 жыл бұрын

New sub here, this video is info gold, just managed to code in replacement abs ecu on 10 golf with Autel thanks to this vid

@LMAutoRepairs 2 жыл бұрын

☺️ Thank you for watching and for your comment! 👍👍👍

@jaydenandkaitlyntv1124 Ай бұрын

Will not code mine right at the start after cloud back up, I went to code and it says coding rejected, what am I doing wrong?

@colindavis4073 Жыл бұрын

Great Stuff Luis..i have a vauxhall Vivaro 2010 bosch system in the shop No ABS COMMS it has the 2 power and 2 grounds at module it has 2.4v can low and 3.6 can high with good resistance ABS module sent away to ecu testing and came back NO FAULTS pin on abs 14 to obd 14 continuity ok and pin 26 to obd 6 continuity ok im pulling my hair out now

@LMAutoRepairs Жыл бұрын

Have you scoped the can lines? 👍👍👍

@colindavis4073 Жыл бұрын

I think I'm following someone's mess I'm going to try that out thanks Luis 😊 great channel I'm subscribed and will definitely donate as you have taught me more about my maxisys ms 908 than anyone else

@LMAutoRepairs Жыл бұрын

😊 Just remember, you might seen can at the module, that could be the car can, not the ABS, you might need to pull the can wires out, and see if there is activity on coming from the ABS unit on it's own... If that makes sense... 👍👍👍

@aminuabdulqadirabubakar4438 2 жыл бұрын

Am always happy watching ur vedio cuz I learned a lot which helped me on my daily car repaired thanks for sharing the knowledge.

@LMAutoRepairs 2 жыл бұрын

😊 👍👍👍

@jasonga 11 ай бұрын

In then old speedo

@ionutpostolache4045 3 жыл бұрын

Great video! Allot of informations, tnx for what you do! By the way... Where is the MaxiIM 608?

@LMAutoRepairs 3 жыл бұрын

In the box...😋 There is some videos coming out on it... Stay tuned... Thank you for watching and for your comment!

@phindashongwe129 2 жыл бұрын

Thanks for such great videos so help recode TCM/TCU 0am 7 speed

@markw3981 Жыл бұрын

Very helpful. It would be nice to know the actual elapsed time. We did channel 025 and it completed in less than 5 mins. We are unable to get channel 026 to calibrate even after 20 mins. Curious how long 026 too to calibrate. Thank you for sharing.

@CarlosPereira-lo3wb 3 жыл бұрын

sem duvida mais um excelente vídeo, parabéns e obrigado um abraço do alentejo

@LMAutoRepairs 3 жыл бұрын

Um abraço! Obrigado! 👍👍👍

@AbdullahAlismaili-h3e 5 күн бұрын

Thanks brother ❤

@LMAutoRepairs 5 күн бұрын

☺️ 👍👍👍

@memekpolska 3 жыл бұрын

Number 1 👍 was talking about Luis 😁

@LMAutoRepairs 3 жыл бұрын

😊 👍👍👍

@prawny12009 24 күн бұрын

how to calculate coding if you do not have a backup? I have read that it has something to do with hardware version, vin number, esp vs non esp, rhd vs lhd.

@LMAutoRepairs 23 күн бұрын

Some tools gives you the possible coding, or the different bytes to construct the coding... VCS for example, not on all modules though...

@supermarketsweeps 3 жыл бұрын

Great video autel never use to give log-in code at least they do now , shame they have not done auto log-in

@LMAutoRepairs 3 жыл бұрын

😊 Yes... Thank you for watching and for your comment!

@markhogy1120 5 ай бұрын

How do you know what channel 060 063 etc

@itsjustchris3306 3 жыл бұрын

Where do you find the channel codes ?

@moatezchaouaf844 2 жыл бұрын

I change the abs block in seat leon 2010 is there any abs specification or code for it and could I progmae it with vcds note : I don't have old abs block to take the coding because it's burn off

@alazzawiahmed8684 Жыл бұрын

Thank you from my heart you are the best

@LMAutoRepairs Жыл бұрын

☺️ 👍👍👍

@tilawat7 Жыл бұрын

I enjoyed these 23 minutes

@LMAutoRepairs Жыл бұрын

☺️ 👍👍👍

@andrewmarkland9411 3 жыл бұрын

Superb Luis, thanks for another informative video.

@LMAutoRepairs 3 жыл бұрын

😊 👍👍👍

@bigjake352 2 жыл бұрын

Thank you for video it’s been huge help, I get all the way to the point of channel 026 basic settings.. at same point during those settings (second value) it fails every time, error 04. Any thoughts? Tried already making sure it was not getting hot

@RafaelMOIO 3 ай бұрын

Did you solved this problem?

@paulosilva-cs7ck 3 жыл бұрын

cara muito obrigado por mostrar esse vídeo me ajudou a tirar bastante duvidas valeu

@LMAutoRepairs 3 жыл бұрын

😊 👍👍👍 Na boa...

@CarsExposed 3 жыл бұрын

Top work as always mate 👍👍👍

@LMAutoRepairs 3 жыл бұрын

👍👍👍 Thanks!

@enriquehernandez6610 Жыл бұрын

Good job

@LMAutoRepairs Жыл бұрын

☺️ 👍👍👍

@jgeorges3061 3 жыл бұрын

LUIS, so to do all this coding/programming we need to have ascriptions from AUTEL or can do it with out it and as always you are AWESOME in my book brother thankyou for sharing.

@LMAutoRepairs 3 жыл бұрын

Hi Yes, if you want to save the coding the way I did... You can manually input the coding, which in that case you do not need an active subscription.... Thank you for watching and for your comment! 👍👍👍👍

@mikesautocare4062 3 жыл бұрын

Did it not have protection system on this so you can't use secondhand unit?

@LMAutoRepairs 3 жыл бұрын

No... no protection... Thank you for watching!

@cristo844 3 жыл бұрын

The Vin off the car its part off the coding!

@lefteristhebuilder6159 4 ай бұрын

I have an Audi A3 '09 and Group 026 (Hydraulic unit disconnecting valves adjustment) never finishes on mine. Have tried it in the morning too with a dead cold engine. Nothing. Am I doing something wrong? Dealership couldn't fix it despite bleeding the system numerous times with multiple ways.

@LMAutoRepairs 4 ай бұрын

Should stop with a error code if I recall correctly... Any codes on the module? 👍👍👍

@lefteristhebuilder6159 4 ай бұрын

@@LMAutoRepairs That's correct, after 1 hour of attempts it returned 148 = Aborted: Outside Tolerance. The only fault code stored is 00003 - Control Module: No or Incorrect Basic Setting / Adaptation. Thank you! EDIT: Brand new ABS module (the hydraulic part is the original) and it was changed under the recall campaign.

@LMAutoRepairs 4 ай бұрын

So, you need to see on wich step that is failing, and see what is out of tolerance...

@ziyadalmasri7458 Жыл бұрын

❤ thank you

@LMAutoRepairs Жыл бұрын

☺️ 👍👍👍

@nemanjadzombic6101 3 жыл бұрын

Thank you for another great video!!!

@LMAutoRepairs 3 жыл бұрын

👍👍👍

@user-smartrepair 8 ай бұрын

Hello. thank you for video. please tell me press pedal with engine on? or ignition on?

@LMAutoRepairs 8 ай бұрын

Hi It is all on the video... 👍👍👍

@user-smartrepair 8 ай бұрын

@@LMAutoRepairs thank you. im not English native so couldn't understood 100%.

@LMAutoRepairs 8 ай бұрын

@user-jdentrepair Understand, but I you are not blind... And I showed it on the video... 17:15

@CANDiagnostic 3 жыл бұрын

Top stuff as always well done

@hashirnawaz4532 3 жыл бұрын

Nice Same like always good video

@LMAutoRepairs 3 жыл бұрын

😊 👍👍👍

@patelvivek4888 3 жыл бұрын

Hi Great Video 👍 Can Autel work with Component Protection for VAG?

@LMAutoRepairs 3 жыл бұрын

Nope... Thank you for watching and for your comment!

@abdonajjai5994 Жыл бұрын

How much does this work cost?

@albrrt430 Ай бұрын

Would it be possible to adapt a second hand abs unit to a 2016 Audi A4 b9 ?

@LMAutoRepairs Ай бұрын

Possibly... I have never tries that though... 👍👍👍

@albrrt430 Ай бұрын

@@LMAutoRepairs thanks for the reply L.M. cheers.

@adriancroitoru7216 3 жыл бұрын

Great job!!💪🏼

@LMAutoRepairs 3 жыл бұрын

Thanks! 👍👍👍

@shanepayback Жыл бұрын

Hi LM. I got A3 sportback 2.0 tdi 2009 i sent the ABS unit for repair got it back now , all that was done was a internal repair, but it has code 00150- plausibility brake booster system, what do i have to do to fix this ? it still has it's original long-code in it , so don't why i am getting this code, any idea ? and the esp light on all the time too.

@LMAutoRepairs Жыл бұрын

What was the initial issue? 👍👍👍

@shanepayback Жыл бұрын

@@LMAutoRepairsthese >> Fault Control unit: 03 Brakes Active faults: 2 Inactive faults: 0 System description: ESP MK60EC1 Software number: 1K0907379CD Software version: 0120 Hardware number: 1K0907379AD Hardware version: H35 Faults: 01276 - ABS hydraulic pump Faulty Intermittent Priority: 2 Frequency counter: 1 Driving cycle: 92 Mileage: 206666 km Date: 2023-06-02 11:04:48 01130 - ABS operation Implausible signal static Priority: 1 Frequency counter: 1 Driving cycle: 51 Mileage: 206658 km Date: 2023-06-02 17:38:48

@LMAutoRepairs Жыл бұрын

I would get in touch with whoever repaired it... If it is coming with a fault that was never there initially... You don't know how it was repaired... Did they repaired the actual unit, or replaced the internals? Difficult to say I guess... Check with them.for advise, as they know what they did and can easier shed some light into the problem... Providing you have obviously made sure everything on the car is OK... 👍👍👍

@shanepayback Жыл бұрын

@@LMAutoRepairs Here's a update. ok so i was going to do a reset on the ABS unit last stitch effort before go back to the repairer. so i disconnected the battery for 20min , then put on battery maintainer, so i could do a full back-up of the car before i did the reset of the ABS unit. the back-up was taking for ever to do after 4.5Hr's it had only went 50% engine unit alone and the other 16 unit still to go, so thought it was going to take all night to do, so i went to get my usb of my phone to keep it charge,but when i came back 5min's later it had completed everything, engine and the other 16 unit's ,strange but ok i thought, so i thought i would try one last time to see if i could delete that code (000150) that could not be deleted before , before i did the reset on the ABS unit , but this time it deleted and did not come back and hasn't for 2 days now! i'm thinking now is it because ABS unti or ECU unit had lost information so how and took all this time to communicate or reprogram each other in some way and that's why the back-up was taking for ever and then suddenly finished very quickly because the ECU and ABS had finished communicating (so i had to do is leave the ignition for a long time to fix this )? this is just my thoughts how this went and how it's is sorted now, hopeful it don't come back now.

@ramiabouassi457 3 жыл бұрын

great video thanks. how do you know the type and number of channels?

@LMAutoRepairs 3 жыл бұрын

I have some procedures instructions saved on my server... just print them out and followed them... Not just for this, but for other things as well... Thank you for watching and for your comment!

@SpeedserviceGR 3 жыл бұрын

You can visit the Ross tech website There you can find all programmings proccedures and channels of course !!!

@LMAutoRepairs 3 жыл бұрын

@@SpeedserviceGR 👍

@emekaonyedire5053 3 жыл бұрын

Hope any scan tool that has coding function can do same eg (thinktool pros)

@LMAutoRepairs 3 жыл бұрын

I haven't tried, but I believe VCDS can do it... 👍👍👍 Thank you for watching!

@HelderPutoPerformance 3 жыл бұрын

Quem sabe sabe e mais nada 👍👍

@LMAutoRepairs 3 жыл бұрын

😊

@roblet5047 3 жыл бұрын

Hi mate this is a mega useful video, I will be starting this whole process tomo and would never have figured all this out even with Vcds. Do you know if it is possible the steering can lose partial power when got Abs fault. I have the 3 lights, 3 beeps and steering feels heavier, car running rough. Have fitted new mechanical part to abs, kept module the same. Car is a Mk2 Seat Leon (Mk5 Golf) platform. Thank you in advance.

@LMAutoRepairs 3 жыл бұрын

Not sure about the steering heavy... bit possibly... until you calibrate the steering angle etc... Will not affect the running rough though... That might be a separate issue... Hope you get it sorted! 🤞 Thank you for watching and for your comment!

@roblet5047 3 жыл бұрын

@@LMAutoRepairs no worries mate i appreciate your response, you are up there with the best. Will see how I get on tomoz.😁🙏🤞

@LMAutoRepairs 3 жыл бұрын

🤞👍

@AnthonyFuxUp Жыл бұрын

Hello! I’m in need of reprogramming as well. How much do you charge for this service in comparison to a dealership?

@carcar5911 Жыл бұрын

Where are you located at? I do reprogramming but I'm in wpb Florida

@Itsmoef 2 жыл бұрын

So 25 works for me and 26 doesn’t. I’m using OBD11 so there’s no on/off button for me. I get the same “calibrated 003” on 25 screen but once I leave it, it goes back to off as if I didn’t do anything. Any help on that?

@LMAutoRepairs 2 жыл бұрын

Never worked with OBD11... so can't really comment... try with another tool, if you can... 👍👍👍

@Itsmoef 2 жыл бұрын

@@LMAutoRepairs I will try my best

@durbinmotorworks6253 2 жыл бұрын

i am currently doing one of these on 2010 golf. I go through long coding and it shows success but after key cycle it goes back to 00000000. It is a used module. Any help would be appreciated.

@LMAutoRepairs 2 жыл бұрын

Whatch this... without skipping... kzfaq.info/get/bejne/qKeDha5jytqlZ4k.html 👍👍👍

@durbinmotorworks6253 2 жыл бұрын

@@LMAutoRepairs Damn man you saved me!. Forever in your debt.

@LMAutoRepairs 2 жыл бұрын

@@durbinmotorworks6253 😊 Glad it help you! And many thanks for the coffee...😉 👍👍👍

@amarimadani5296 3 жыл бұрын

hey brother..can MS908spro remove component protection for Audi A6?thankx

@LMAutoRepairs 3 жыл бұрын

No... Thank you for watching!

@nigelwilks5767 2 жыл бұрын

Hi there I have a abs problem pump code is 1ko 614 517 bd but hard to come across second hand. I would like to know if I can use a pump with different code but put my software in any help would be useful thanks

@LMAutoRepairs 2 жыл бұрын

Yes... there is a few suffixes that are compatible... I don't know now from the top of my head... Actually, I think I showed on the video... or might not...😋 👍👍👍

@arnaldoventura2 Жыл бұрын

Very Helpful can do the same with e61 525d 2004''????

@LMAutoRepairs Жыл бұрын

Hi The procedure might be different... don't think I have replaced one of those, so not really sure... 👍👍👍

@omerward9261 Жыл бұрын

hi mate fantastic video you do can the im608 code this unit

@LMAutoRepairs Жыл бұрын

Yes it can... 👍👍👍

@randolhernandeznaranjo1306 2 жыл бұрын

Very good successfully

@LMAutoRepairs 2 жыл бұрын

😊 👍👍👍

@trevormansfield6740 3 жыл бұрын

Hi, how did you find out the security code number and the basic setting channel numbers please?

@LMAutoRepairs 3 жыл бұрын

The code as you have seen if you watched the video, Autel shows you the code... The channels, I have some documentation, but, loads of information out there...😉 Thank you for watching and for your comment!

@trevormansfield6740 3 жыл бұрын

@@LMAutoRepairs I’ve rewatched that part and I’ve got it now. I must be getting old. Thanks for replying 👍

@LMAutoRepairs 3 жыл бұрын

We all are...😋

@Melik1 Жыл бұрын

Hello, I removed the Passat b8 instrument panel unconsciously, the abs codes have been deleted, where can I find the codes, thanks in advance.

@LMAutoRepairs Жыл бұрын

Hi What exactly di you mean? I am confused... sorry... 👍👍👍

@Melik1 Жыл бұрын

@@LMAutoRepairs Where can I get Passat b8 ABS code?

@LMAutoRepairs Жыл бұрын

You mean the coding?

@Melik1 Жыл бұрын

@@LMAutoRepairs abs esp electronic handbrake airbag how do i turn off the lights?

@LMAutoRepairs Жыл бұрын

What do you mean turn the lights off? I am really confused... If you have the esp and the abs lights on, scan the the abs module and see which faults are in the module... from there repair the faults and clear the codes... That should extinguish the lights... Same goes for the airbag and for the handbrake... though some can be caused by other systems, and do not necessarily indicate a fault with the particular system... Again, a scan should point all of that...

@johnjimjohnston 3 жыл бұрын

so this does do vw compondent protect

@LMAutoRepairs 3 жыл бұрын

This was not protected... Thank you for watching!

@stefanantevski3424 2 жыл бұрын

One question,old unit was repairable or not?

@LMAutoRepairs 2 жыл бұрын

Possibly... but not economically viable... Thank you for watching!

@passionmeca4951 2 жыл бұрын

Thanks for vidéo

@LMAutoRepairs 2 жыл бұрын

😊 👍👍👍

@777giba 3 жыл бұрын

Nice temperature.

@LMAutoRepairs 3 жыл бұрын

😊 👍👍👍

@walideamine9540 2 жыл бұрын

Hello I wish to help me how to get access permission code and thank you for everything ❤️

@marcomarques4060 2 жыл бұрын

Hello. I got vw golf mk6 2010 1.6tdi with abs problem. On my case I got no reading on osf and nsr. The module recognise the sensors clear codes ok but no reading. If I try with a strong magnet on the nsf and osr I got readings. Do you come with anything like this before? Thank you

@LMAutoRepairs 2 жыл бұрын

Have you checked the reluctor rings? Are the sensors, genuine or aftermarket? 👍👍👍

@marcomarques4060 2 жыл бұрын

Thank you so much for the reply Luis. The rings are good. I love you videos My name is Marco I’m Portuguese by the way. Thank you

@marcomarques4060 2 жыл бұрын

@@LMAutoRepairs Sorry, yes original sensor

@marcomarques4060 2 жыл бұрын

@@LMAutoRepairs Thank you so much for the reply Luis. The rings are good. I love you videos My name is Marco I’m Portuguese by the way. Thank you

@LMAutoRepairs 2 жыл бұрын

I would start to check wiring then... connections etc... Load test the sensors wiring, just to make sure...

@fiatbravodriver 3 жыл бұрын

Hi would you be able to code a VW T5 2006 abs pump for me please? I have the old pump but its not fitted to the van and I don't have a backup of the code. I have looked on your facebook and could not find a way of contacting you.

@LMAutoRepairs 3 жыл бұрын

Did you had communications with the old unit?

@fiatbravodriver 3 жыл бұрын

@@LMAutoRepairs I think so. The fault code was 01130 abs operation. The pump went to be refurbished but the company said a coil has gone and it’s non repairable.

@LMAutoRepairs 3 жыл бұрын

OK... So, in that case, you can just plug in the old unit, copy the coding and then put it on the replacement unit...

@mardina1a 3 жыл бұрын

Whadda pain is that, if i wanna use second hand unit.why do they do that?every part of car needs procedure when they're swapped.whadda mess

@LMAutoRepairs 3 жыл бұрын

😊😋 👍👍👍👍

@SpeedserviceGR 3 жыл бұрын

Which model is Autel diagnostic tool?

@LMAutoRepairs 3 жыл бұрын

MS908P Thank you for watching!

@SpeedserviceGR 3 жыл бұрын

@@LMAutoRepairs great tool I will buy it !!!

@neilmurphy845 3 жыл бұрын

What does the flashing glow plug light mean

@LMAutoRepairs 3 жыл бұрын

O explained during the video... 😉 MAF was disconnected...

@ADDAUTOMOBILESERVICES 3 жыл бұрын

👍

@LMAutoRepairs 3 жыл бұрын

😊 👍👍👍

@techgamer1597 3 жыл бұрын

WagenVolks Caddy

@CANDiagnostic 3 жыл бұрын

More that one way to skin a cat.......

@LMAutoRepairs 3 жыл бұрын

😋 Indeed...

@VSTV1993 3 жыл бұрын

With VW just drive the car/van over 5mph and it will relearn/reset the module

@LMAutoRepairs 3 жыл бұрын

Not on this one... The car was driven way more than 5 mhp to come to me... that didn't solve the faults...😋 Thank you for watching!

@VSTV1993 3 жыл бұрын

@@LMAutoRepairs ahh, you learn something new every day 😁

@inshafmohamedseyedmohamed4964 2 жыл бұрын

Hi dear whats your Autel serial Number - i like to buy one Diagnostic machine like yours

@LMAutoRepairs 2 жыл бұрын

Model is MS908P I believe has been replaced now by the MK908P... Thank you for watching!

@bassb466 2 ай бұрын

? ???

@LMAutoRepairs 2 ай бұрын

🤷‍♂️ ? ???

@tefocharlesmodise9937 Жыл бұрын

🙄🙄🙄🙄 💀💀💀💀

@LMAutoRepairs Жыл бұрын

🤔🤔🤔🤔 🤷‍♂️🤷‍♂️🤷‍♂️🤷‍♂️