#XH

Рет қаралды 47,115

Жыл бұрын

This video demonstrate about the charger module XH-M601 which is used to automatically switch ON or switch OFF the battery charger at preset voltage level.
Here viewers can learn how to calibrate or set the minimum and maximum voltage level of the module.
XH-M601 module:
robu.in/product/xh-m601-12v-b...
Variable voltage source module (dc to dc buck converter)
www.google.com/aclk?sa=l&ai=D...

Пікірлер: 41

@salmanhabib1951 8 ай бұрын

Tnx vaiya.... module ta onek age kinesilam...... setup korte parini ......aap ka video dekh kar hogaya.....tnx

@paulsmi55 4 ай бұрын

Excellent, thank you !! 👍

@CSTech2024 4 ай бұрын

🙂Welcome !!

@motalebhossain1074 5 ай бұрын

it is a very good video. thank you very much you should good luck.

@CSTech2024 5 ай бұрын

Thank you so much.

@spelectroniclab Жыл бұрын

Very nice video sir

@CSTech2024 Жыл бұрын

Thank you so much.

@tnamen1307 Ай бұрын

Can I get the reverse output as mentioned below??? Simply as.... Relay should be OFF when car battery voltage is from 0V to 13V. Relay ON when battery voltage is from 13.1V to 15V. Please help how to achieve this output.😊

@safuddinsardharwalla980 9 ай бұрын

Can it be used for 20v 3.5 or4.7 amp in put what will be a period of the module.

@NEVEREVERGIVEUP478 6 күн бұрын

555ic jeat while using charger why??

@nmreena 11 ай бұрын

Nickel Cadmium Battery Charging and discharging procedure and connection diagram

@MrlordxGaming Ай бұрын

Last steps led off nehi ho raha hai , anti clock wise ghumakar last tak jane ke bad bhi

@bharatmatakijai105 7 ай бұрын

Ye circuit maine without 555ic ke bina banaya hai 3 relay ko use karke😂🤣🤣

@ionutzionutz7106 11 ай бұрын

Hello. nice video, well explained. Can you tell me, please, what are the adjustment limits of this circuit? I would like the relay to connect at a voltage of 13.5 volts and disconnect at 16-17 volts. I want this because I want to use it for an application with a car. When the engine is off, the battery has approximately 12-12.5 V. After starting the engine, the voltage increases because the alternator starts charging and when 13.5 volts are reached, the relay will engage. The upper value of 17 volts is chosen so that the relay remains connected as long as the engine is running, because in fact under normal conditions this value of 17V cannot be reached with an alternator in a 12V car. After you stop the engine, the value of the battery will drop below the cut-off threshold of the relay. This is what I would like to do... do you think that the circuit falls within these limits?

@CSTech2024 11 ай бұрын

Thank you so much sir. I will try to solve your problem. Till now I used this setup in my home with 7AH battery only.

@khushjitsingh 3 ай бұрын

When connected with battery and the battery discharges and drains to 9volts then the led on the pcb glows but relay doesn't work due to 9v. Under this situation what can be the solution.

@CSTech2024 3 ай бұрын

We can set the minimum charging voltage to a little bit higher so that the relay can be operated.

@tnamen1307 Ай бұрын

@@CSTech2024🙏🙏🙏🙏 Sir, please tell me how to get this output using the same module xh m601... Relay OFF when car battery voltage is from 0V to 13V. Relay ON when battery voltage is from 13.1V to 15V.

@abhikdutta1842 10 ай бұрын

Is it possible to do the settings without using dc to dc buck converter if so then please reply

@CSTech2024 10 ай бұрын

Thanks for watching video. Actually for calibration, we need a variable power supply. We can use 317 based variable power supply also.

@abhikdutta1842 10 ай бұрын

@@CSTech2024 Pls suggest battery or any other method as buying a dc to dc converter increases the cost

@CSTech2024 10 ай бұрын

We can use 317 based variable power supply also in place of dc to dc converter

@mdbadsha4171 9 ай бұрын

An ACDC fan can be run with this circuit

@CSTech2024 5 ай бұрын

It depends upon your battery, not upon the module.

@devprosad7005 6 ай бұрын

How use it with DC input (From solar 12v) ,not using 220v ac charger please reply

@grvsays 5 ай бұрын

Got any ideas ?

@devprosad7005 5 ай бұрын

@@grvsays nope, it's worthless

@rahulsaha8586 5 ай бұрын

Battery charger contotler module circuit diagram ?

@CSTech2024 5 ай бұрын

I purchased the module online. Don't have the circuit diagram.

@grvsays 12 күн бұрын

input is DC or AC?

@CSTech2024 11 күн бұрын

The charging input is AC given to the battery charger.

@unnikrishnan6608 Жыл бұрын

Low voltage 12v need to on pcb below 12v. Please prepaid video sir

@CSTech2024 Жыл бұрын

Thanks for watching the video sir. Please clarify your message. I am unable to understand.

@MongalMondal96 7 ай бұрын

how buy

@CSTech2024 7 ай бұрын

You can buy from robu.in

@shahriarshakil9797 Жыл бұрын

Circuit Diagram?

@CSTech2024 Жыл бұрын

Hi, thanks for watching the video. xh m601 module can be purchased online. The setup circuit is already given in video.

@muhammadmahmood6986 Ай бұрын

This video was very helpful! I have power cut off module and input source switcher in one module! Slightly different in structure of this one... Plz can you make a video for my module? I don't know how adjust it! Kindly share your email address, i will send you pictures and instruction guide! Plz adjust it for me.