built in looping and epic effects per channel, who wouldve thought! i still find the db4 was the most playable mixer i've ever owned. the only downside to it was its kinda ugly and confusing to look at initially 🤣

Hi, Thanks for the message, If the DVS jumpers are not fitted, then 23C will send the master record feed on USB 1&2. It is these channels that you will need to setup and route to the desired recording software. For guidance on what increments the pitch control can be set to and how to action this, please contact NI support. support.native-instruments.com/hc/en-us Thanks, Luke

There is a button actuation required for the effects as well. It’sa little blue dot next to the effects

Hi Zigane, Thanks for the message, Everyone’s workflow is different. But the great thing about mappings, is that you can add whatever you like and build upon any existing map so that it is tailored to your preference. Best regards, Luke

Hey which Mapping? .. On there Page? i Downloaded and there is no Mapping its just the Commands! you have to Mapped all by your self!!!! it didnt work for me! :( Or which one do you have? can u share it?

Hi DJ Rob, Thanks for the message. We can confirm hat K2 support is active for Windows 11. www.allen-heath.com/xone-software/ Please note; We are aware of previous problem with the Xone:K2 on computers with the AMD Ryzen processor. The displayed symptom seems to be failed enumeration between the host computer and the K2 controller. From all cases we have seen so far, it is solely on these Ryzen-based machines. However, we are happy to inform you that we now have a working update (v2.5.0) for Xone:k2 to run on Ryzen-based hardware. The caveat is that the update needs to be performed either on an Intel-based Mac or Intel PC. However, once the K2 device has been successfully updated on a supported platform. It will connect and run just fine on the Ryzen system. I have attached a link below to the v2.5.0 updater for both Mac OS and Windows PC. Please use the one that is relevant to you. Unpackage the zip file to your desktop and open the updater. You will be prompted to connect the k2 device. Once the connection has been established run the updater and follow the on-screen instruction. www.allen-heath.com/ahproducts/xonek2/#tab5 If the installation proves to be successful you can connect and continue to use the k2 with the Ryzen hardware. If you have any further question or require assistance, please drop us a line to support@allen-heath.com Best regards, Luke

Hi Mix man, Thanks for the message. For this you will need to modify and Taylor the mapping to suit your setup. To do this, please go in to Traktor’s controller management dialogue. Select the desired controller assignment you want to change/alter. It will then be displayed in the ‘device mapping’ where you can use the drop down to change the MIDI channel. However, you will need to ensure that you select the same note value after the channel number. I hope this helps! Best regards, Luke

Hi Paul, For assistance with this, please drop us a line to support@allen-heath.com. Thanks, Luke

hi there! i am getting the same problem :(

Hi Becca, Thanks for the message. For K2 in Traktor, you need to select Generic MIDI under the device option. K2 then will appear in both the in & out ports drop downs as a selectable device. If you require any further assistance, please drop us a line via support@allen-heath.com Thanks, Luke

Hi Francois, Thanks for the message, Yes, running two K2 devices on the same computer, you must set each device to a separate MIDI channel. There is advice on how to do this on page 11 of the user guide. www.allen-heath.com/content/uploads/2023/06/XoneK2_UG_AP8509_3.pdf Best regards, Luke

Hi Miklós, Please ignore the naming convention on K2 soundcard. Take it that, USB 1&2 are L&R for the headphone out. And 3&4 are L&R for the RCA connectors. I hope this helps! Best regards, Luke

Hi, The Cue volume and mix are accessed by having the cross fader assigned to mixer in the software. The soundcard also needs so to be running in internal mode in the software setup dialogue. Headphone control is not applied to the mapping, as it would have been built for use in conjunction with a mixer in external mode, so you will need to add then controls yourself. Below is a link to a video that shows how to map the pots. kzfaq.info/get/bejne/qdyUfNWl1cjViaM.html Thanks, Luke

sorry for the wait Otto. just as soon as the overlay graphics for it are ready... hope to see them online in April

@@xonedjofficial How's that Stem mapping coming mate?

Adding a second K2, each device would need to operate on a separate MIDI channel. Therefore, the mapping would need building upon to incorporate the second K2/MIDI channel. You may find the videos below useful when adding to a Traktor map kzfaq.info/get/bejne/qdyUfNWl1cjViaM.htmlsi=Lo1dLd54eF3vpZeo kzfaq.info/get/bejne/hLhji6ql25e0hKs.htmlsi=dMTWNb0IQiyNNbsm kzfaq.info/get/bejne/bM5iY6SQrtreaGg.htmlsi=-Gl8L4a3DFIYrCk0 Thanks, Luke

Hi, The power on setup button should be pressed whilst connecting the K2 to USB or X:link (bus power). However, this is only to access the device setup. When connecting a K2 it will seem unresponsive until it has been mapped to software. If the K2 goes through the power-up sequence (LEDs flash from top to bottom). Then it is likely that this is the case. If you require further assistance, please drop us a line to support support@allen-heath Best, Luke

Hi Luke, Thank you for the quick response. I've done it all as you wrote with the little help of the video and it works. Cheers!@@xonedjofficial​

Hi, There is a map for Ableton of the K2 product page. Though, it may be a little dated now. Feel free to try it out and see how you get on! www.allen-heath.com/ahproducts/xonek2/#tab4 Thanks, Luke

@@xonedjofficial Yes. I have it downloaded. Is there a video where it is explained? Thank you.

Hi Gatos, for assistance with this, please drop us a line at support@allen-heath.com Thanks

@@xonedjofficial thank you very much, the problem is solved, it was a bad rca adaptor.