xTool 10W vs 20W D1 Pro Diode Laser Engraver | Easily Upgrade Laser Modules

Рет қаралды 4,571

Күн бұрын

In today’s video, we’ll be comparing the 10W and 20W xTool D1 Pro Diode Laser Engravers to see the different results you can get from each. Also, we’ll show you how to quickly and easily change out the laser heads/modules of the xTool D1 Pro Diode Laser. Hope you enjoy the video!
⏱TIMESTAMPS⏱
0:00 Intro
0:48 Unboxing 20W Laser Module
3:00 Setting Up Comparison
4:30 Testing 10W
5:44 Changing Laser Module
6:23 Testing 20W
6:27 Results
7:32 Side by Side Comparison
8:30 Our Thoughts
11:05 Outro
💻SOFTWARE💻
xTool Creative Space: bit.ly/46tyyjo
LightBurn
🎬 PRODUCT LINKS🎬
xTool Website Links: bit.ly/46Ej1gZ
D1 Pro 10W: bit.ly/47FJOdS
D1 Pro 20W Laser Module: bit.ly/3uHPtl7
Amazon Links
10W Kit: amzn.to/46mSXGT
20W Kit: amzn.to/4ae01rt
(As an Amazon Associate, we may earn from qualifying purchases when you use the link.)
🎬VIDEO LINKS🎬
xTool Playlist: • xTool Laser Engraver
Laser Engraving Playlist: • Laser Engraver
The information provided is for general information and entertainment purposes only. Your use of the site is solely at your own risk.
© Project Anonymous 2023 - All Rights Reserved
🎶MUSIC🎶
Contender - TrackTribe
Don’t Wanna Be - Kwon
Happytoseeyou - Sarah, The Illstrumentalist
Jazz In Paris - Media Right Productions
Treat Yourself - Dyalla

Пікірлер: 21

@humbleacres5106 6 ай бұрын

Great comparison video! You have helped me to decide what laser I'm getting. Thanks again!

@ProjectAnonymous_Duo 6 ай бұрын

Glad we could help! Thanks for watching!

@sannyassi73 2 ай бұрын

I've been trying to decide if I should upgrade my 10 watt to either 20 or 30. This doesn't totally answer the question I was looking for but it does help me a lot. Thanks for the video, it is very helpful despite only partially answering my question (no your fault, it's not what the video was about). Anyway, take care and thanks for the vid :D

@ProjectAnonymous_Duo 2 ай бұрын

Thanks for watching!

@ssteffe2 27 күн бұрын

I think will help in my decision.. thanks

@ProjectAnonymous_Duo 27 күн бұрын

Awesome, thanks for watching!

@Optikification 2 ай бұрын

I have an elegoo phecda 10w and thinking of upgrading the head and psu to 20w. Was looking for a comparison video to show if its worth it. Thanks for this info.

@ProjectAnonymous_Duo 2 ай бұрын

We are glad you found it helpful, thanks for watching!

@patatebanine4278 5 ай бұрын

Hi, is it easy for you to switch the 10w for a 20w on the machine?

@ProjectAnonymous_Duo 5 ай бұрын

Yes, we found it very easy to switch...one plug, one thumbscrew, and changing the power brick. Thanks for watching!

@katranitsa 6 ай бұрын

if you change the laser and the power adaptor is the same what will be happen?

@ProjectAnonymous_Duo 6 ай бұрын

We haven’t tried that, to be honest, but, I don’t think it would be catastrophic, maybe some loss of power?

@bigmd1343 4 ай бұрын

I don’t understand what the thought process was when they designed the connector for the laser module. I change my module often because I also have the IR module. They don’t last long and I can either rewire or change the whole wire harness. So many really well thought out designs with the D1. But some I really wonder what they were thinking.

@ProjectAnonymous_Duo 4 ай бұрын

We agree it is not easy to reach the connector. We aren't sure about the longevity yet, but we definitely have to be very careful with it. We have liked the set up so far, but there is always room for improvements. Thanks for watching.

@rusticbear-bp9ii 5 ай бұрын

how can i speed up engraving borders. they take far longer than the actual middle bit im doing. today one piece took 90 minutes the border took 65 minutes of the 90

@ProjectAnonymous_Duo 5 ай бұрын

The only thing we could suggest is if you haven't already tried, is to create separate layers for those parts, then you can adjust the speed and power. Thanks for watching!

@the_edge_of_time 6 ай бұрын

Have either of you tried something that would use both 10w and 20w?

@ProjectAnonymous_Duo 6 ай бұрын

We like the 10w for engraving and the 20w for cutting, but we haven't swapped them out for one project yet.

@QuiltersHandyman Ай бұрын

Unboxing a total waste of time....there are dozens and dozens of these types of videos. Get to the use of the machine

@robertballesteros1187 5 ай бұрын

hi, have you attempted to cut through metal with the 20w? will it cut through metal? i'd like to see a video of that with the results. thanks! 😎

@ProjectAnonymous_Duo 5 ай бұрын

We have not attempted to cut through metal with the 20w. We will have to do a bit of research on that. We'd imagine if it is at all possible it would have to be extremely thin metal and very low thermal conductivity. As we understand it, a fiber laser is the best for use with metals. We did use our fiber laser in a video we just posted to cut through anodized aluminum if you are interested in checking that out: kzfaq.info/get/bejne/a92plcd7nLC8nZs.html Thanks for the suggestion and for watching!