Swapping in a Chinese carb to get this beauty running!
Пікірлер: 53
@TheYork948 жыл бұрын
after watching you videos for years finally got myself a 28" screwdriver! and man you aren't kidding they're very handy!
@PowerModzOfficial8 жыл бұрын
I know right!
@lilCHIQUIS18 жыл бұрын
Louie good to see again brota. Keep up the good work.
@shaunlittle49868 жыл бұрын
good buy. looks like a great trail beast!
@slimjim1198 жыл бұрын
looks like a fun ride
@imoney59898 жыл бұрын
Great video! I was wonder if you could do a old maybe 80-90s dirt bike build from scratch with minimal editing so I can learn a lot on these older bikes.
@jimmykeeler45875 жыл бұрын
That's cool I have a 1987 bw80 just got it
@rippinmachines2 жыл бұрын
I hope you still have your BW and some of your other BW mod bikes
@wickedfastautomotive64872 жыл бұрын
Were does all the hose go to on the carburetor I got mine with only fuel hose hooked up no others hoses on the ports
@dwadholm18 жыл бұрын
Star Bright Hull Cleaner would work good to clean up that fiberglass.
@Easiermarlin338 жыл бұрын
I've got a 1985 moto-4 200cc, w/ original carb and the popping noise, I've tried adjusting it and I've taken it out and cleaned it and it still pops, at this point I'm interested in getting a new/different carb to try in it. Where did you get the Chinese carb?
@Grainsauce6 жыл бұрын
At the end of the video, what screw was he adjusting, was it the idle fuel mixture screw? A pilot jet screw?
@jacobbowcutt6933 Жыл бұрын
What ended up being the fix on the carb I’m struggling with the same carb right now.
@sergemongeon85334 жыл бұрын
What size sprocket on the bike? I’m installing a 25 inch tire and wondering what would be the best combination .thanks!
@AjackLee48 жыл бұрын
Gotta do rides with the 200x and the BW200!
@starpuss8 жыл бұрын
I miss my old Bw200 , Had to do a LOt of work on her ,lots of videos on my page, and then found it was too gutless for what it wanted it for :(
@nilesable8 жыл бұрын
BW 200s were fun,but the 350s were a beast.
@Vjiovino Жыл бұрын
What China carb did you use ? The ones im finding are too big to fit the maniford
@landisowens77425 жыл бұрын
I have a BW200 and I’m having trouble with the carburetor and boot ,What’s the info on the new carburetor and whats type of Boot is that.????
@mikemccabe9528 жыл бұрын
alot of those and fatcats listed often in phx az craigslist and since this is az thers almost no rust, we're too hot & dry for dat
@ronniebprospecting74718 жыл бұрын
Nice moves Louie
@ninamiller49925 жыл бұрын
What did you do with the vacuum lines?
@nickdehoop40738 жыл бұрын
Nice intro!
@ivanslawsky44628 жыл бұрын
Love these I just got rid of mine, really regret it
@drummerboii9114 жыл бұрын
Would a blaster engine fit on big wheel
@shawnduframe7 жыл бұрын
what back tire are you running
@kylechupick22323 жыл бұрын
How do you adjust the idle on it
@landisowens77425 жыл бұрын
Boot is too tight around the carburetor and pushes the o ring out of place???
@jorgepolacabrera1561 Жыл бұрын
What it's zise rear tire please my friend
@Rs-fi2uf7 жыл бұрын
Anyone know the specs on a stator for these machines
@reesewilliamson33468 жыл бұрын
try using hairspray to put grips on
@MrFireline558 жыл бұрын
I want a bw350
@brianclark52552 жыл бұрын
I've got a 1985 BW200E that I am going to try to restore
@brianclark52552 жыл бұрын
I got the same carb so I looked at your hook up my carb had sat for 20 years with varnish slug so I just got a new one and the transmission I had too replace the gears I bought them as a set and frictions and looked at the rings and piston cylinder was top part had a ton of carbon build up which would not allow the piston too move all fix and ready too reinstall in bike my back tire is huge massive still holds air and not much dry rot
@porkchop3619683 жыл бұрын
Where can I find a rear tire for a BW200? Specs say 23x12-9 cant find that size...will another size work?
@burkey4262 жыл бұрын
I used a Deestone D930 22x11.00-9 as a replacement for the rear. It’s a little smaller than stock but has an excellent rounded profile. A lot of the tires in this rim size are meant for quads and have a very square profile which makes for a horrible handling. I also used the same tire in the correct size for the front.
@nilesable8 жыл бұрын
Swap out the foot pegs for wider ones,or since you have a welder make them wider,your feet will thank you for it.
@jorgepolacabrera1561 Жыл бұрын
Because l go check out price rear tire
@mikehuneault826 жыл бұрын
Did you find new plastic? If so where from?
@lilblazenboi6 жыл бұрын
Mike Huneault Bigwheelconversions.com
@sledderguy18718 жыл бұрын
Sweet
@ludicrous87948 жыл бұрын
Louie una buena moto
@crf1008 жыл бұрын
the air cleaner might fix the jetting
@PowerModzOfficial8 жыл бұрын
that's what Im hoping for - its on order now.
@crf1008 жыл бұрын
+PowerModz yea that would be nice I used to have a honda 200es that would only run with a airfilter
@user-cv5gl6kh3k6 ай бұрын
your plastics are still good wetsand them with1000 then 2000 polish plastics with Meguires Plas T X buff thorougly and you shall have NOS plastics
@justinmccafferty33468 жыл бұрын
wanna sell it lol?
@vinto345 жыл бұрын
The cdi can make them misfire as well...they are a weak point on the bw200.
@197309284 жыл бұрын
Know where I could find a CDI?
@vinto344 жыл бұрын
@@19730928 FatTyreconversions.com....They have aftermarket cdi for electric and kick start only models.