The "other washer type component" is what dropped out on my garage floor. Thanks so much for showing that!
@wbsnow932 жыл бұрын
Of course! I tried to include as many things that could go wrong cause that's where I usually get stuck when following youtube tutorials
@R6EXY_3 ай бұрын
You just saved me $50. I was just about to purchase the entire assembly off eBay because I didn't know what was wrong with my signals. I watched your video, saw how much of the old earwax lube was in there, cleaned it all out and regreased. Now my turn signals work BEAUTIFULLY. Great video man. Thanks!
@wbsnow933 ай бұрын
😃 that's awesome!! Glad I could help a fellow biker
@R6EXY_3 ай бұрын
@@wbsnow93 Also, I'm in Washington too, haha. Kent, more specifically.
@Rev25110 ай бұрын
I had a very inconsistent turn signal in either direction on my R6. The main problem was that the metal contact plate was jammed in because it was dirty. After disassembling and cleaning now it works as expected. Good video
@wbsnow937 ай бұрын
I'm glad I could help!
@zakalln3 ай бұрын
thanks for the vid, fixed my right side turn signals not working
@wbsnow9318 күн бұрын
@@zakalln awesome! Glad I could help
@yaasinlutta178818 күн бұрын
Thank you helped Humpty Dumpty a great deal cheers for the efforts man
@wbsnow9318 күн бұрын
@yaasinlutta1788 of course! Glad I could assist!
@bandaral-fagih41562 жыл бұрын
I followed your amazing instructions step by step, and now my turn signal works.. Thanks to you. keep up with these good quality videos .. what is your next video for bikers?
@wbsnow932 жыл бұрын
I'm glad I could help! It was a pretty straight forward fix to a very annoying issue. Not sure what video I will do next!
@Journal_w_Amber2 жыл бұрын
Great video!
@wbsnow932 жыл бұрын
Thanks! 😄
@Dlgeis2 жыл бұрын
Very important use only dielectric grease on electrical components. If your grease contains conductive compounds like lithium, graphite. molybdenum you can set up lots of electrical leak paths or even direct shorts.
@etka91672 жыл бұрын
Great and detailed video. Thank you
@wbsnow932 жыл бұрын
Thank you, I'm glad I could help!
@888jannn2 жыл бұрын
NICE job ...thanks...👏👏👏👏
@wbsnow932 жыл бұрын
Glad I could help!
@Dlgeis2 жыл бұрын
Instead of removing all of the components just separate the halves, wrap a clean rag loosely around the switch, use electrical contact cleaner with a straw to clean from as many directions as you can get to. Apply fresh dialectic grease to areas that touch and button it up. You can purchase dielectric grease in a spray that will penetrate then evaporate the carrier leaving grease on places inside the mechanism if needed.
@wbsnow932 жыл бұрын
Not a bad idea!
@muhammadfadhil4821 Жыл бұрын
Your video save my day.. done subs. 😁
@wbsnow93 Жыл бұрын
Glad I could help!
@harryw95984 ай бұрын
nice job, close for me my passing light switch is kinda sluggish. to return wil have to dig in deeper?
@wbsnow9318 күн бұрын
@harryw9598 thanks! Yeah probably the switch just needs fresh lube
@colinscott30667 ай бұрын
I did everything in the video but now only my front right turn signal doesn’t work while the back right does, it also blinks at a normal speed. Any ideas on what it could be?
@wbsnow937 ай бұрын
Sounds like wiring to me. I'd guess just a coincidence that it happened while you cleaned the switch. Are your blinkers 'running lights'?
@colinscott30667 ай бұрын
@@wbsnow93 yeah they are running lights
@hirokihiroki30772 жыл бұрын
I love your fender eliminator:) Where’s one?? I wanna try same modification.
@wbsnow932 жыл бұрын
Thanks! It's made by TST industries, and it's cheap! And then I used some ebay leds to make the blinkers. TST STANDARD FENDER ELIMINATOR YAMAHA R6 2006-2016 tstindustries.com/tst-fender-eliminator-yamaha-r6-2006-2016.html
@hirokihiroki30772 жыл бұрын
@@wbsnow93 thank you 😊 I’m looking forward to watch new R6 videos . Your videos are useful:)
@wbsnow932 жыл бұрын
Glad I could help! I'll get some more out soon
@BranNewVNM Жыл бұрын
5:50 Any clue where I can find one of those balls?
@wbsnow93 Жыл бұрын
ah damn man, you could try McMasterCarr but they probably only sell high qtys. If you have a caliper you could measure the size. Looks like theres a kit of a bunch on amazon www.amazon.com/Tanstic-Precision-Stainless-Bearing-Assortment/dp/B09C1J2JPS/ref=sr_1_2?keywords=steel+ball+bearing&qid=1685546433&sr=8-2