thanks, did the re-jet and it made the bike run so much better, especially when cold.

Your videos help me so much

When you rebuild the carb; how far in do you screw the Idle Screw in at the onset?

Two Questions on this bike: In order to get compression when kicking i need to put in in gear and rock it for each kick, is something out of adjustment? Question 2, when electric starting this bike if it does not fire within the first couple of seconds the starter stops spinning and there is some clicking in the electrical components in the back under the seat, whats up?

Kudo's to Yamaha engineers designing the carb that you an easily remove the float boat and clean/replace jets if you want to. I don't remember it being like this on my xr70?

Hey like your videos man you should do more engine tutorial videos

For what it’s the two wires goes in the carb?

Hey Ik this is 8 years later but the two connotations on the carb I’m trying to order one and i they don’t have that can you explain

I have a pw80, my son is getting taller…would you recommend a shock extender or larger shock? Thx

What are those two wires running to the carb, I bought a new one to install and I don’t know what to do with those wires , I can’t get I it started I’m thinking it has to do with these wires

Sorry about the nail. But how tall are you? I'm like6'3 myself and that ttr looked smaller. And thanks for the vid. Did it produce more power

Does this fit 2006 ttr90

i know this is 7 years later but were did you get your parts from for the ttr 90?

Is the 90cc determined by the 90 carb?

Thanks man

Not sure if you'll reply but could you tell me what the hose that's about 4-6 inches that runs into the gas on/off/ reserve switch. Mine is cut and won't run until it's replaced

i know it's been awhile and you sold it but where did you find those jets? I found some on ebay but it says for yz and cr? does it make a different

OK thanks

hey i have a stock tar 90 does this jet kit change make the bike have more rev and make it go faster

What is the seal at bottom of carb mine is same as yours where goes around the bold but can't find that version antwhere

I have a ttr90 n it has them electrical connections- what are they for? Cuz I got a new carb for the bike n it don't have them electrical connections!

Part number for jets?

Hey quick ? My ttr 90 in nuetral when I rev it decel pops and when I put the choke fully on it chugs then dies . Is that normal or only use choke in winter ?

I lost first gear on a ‘03 TTR90. I can shirt 2 to 3 but unable to get into first gear. What could I possibly getting into. The bike how low miles and I was hoping to repair want is only broken. Local Yamaha, suggested a full rebuild = $1,800…!

tanx broh yea i just did it like u u know so wher can i buy them at ..????????? so 95 main and da 15 for da pilot tanx fo helpn me out broh

Hello, I just bought a brand new Battery for my TTR90. Do I have to charge the new Battery before installing it or just replace. My buddy told me I have to charge it 1st, but not sure how and how long if that is the case. Thanks !!!!!!

Dang why can't the klx140L carb be so easy to work with

Where can I buy this?

nice video broh but i got a ? wat are the bigest jets i can get for dat ttr90 i got one today but my fuel valve petcock iz broke and i need to oder one oh and i did all my sht like your hit me need help

And the stock ones were?

Sorry....had to laugh about the nail in the tire. Otherwise, this is a great video!

Quick question. I am trying to work on my sons 2001 ttr 90 .I have taken apart the carb a million times cleaned the jets etc. The bike starts up fine as soon as I take it of choke it stalls. What am I missing?? I learned from watching all your dirtbike videos they were very good.

Is it the same for a pw80 or no?

Hi Mate, Where is the best place to order the 2 jets from please? Cheers Brett

how do you do a willie

We're can I buy them from ?

where can I get these jets

I have a ttr90 and it idles high a guy had a video about a ttr50 where he drilled a whole into the carb and popped this cap out so that he could get to the idle screw. Is there really a cap covering the idle screw or is there another reason it’s idling high. There throttle connectors don’t control the idle and there’s no idle screw showing so I figure it’s hiding behind the tiny cap

my bike iz leakn gass from dat line wher u let da gas leak so u can take out the folt u konw y iz it leak en

How do you do the exhaust modification and intake modification?

Where is the idle screw

faashoooo