Young Manufacturing BCG Examinations: 1 was a physical because it passed. 1 was an autopy because the Carrier Key Screws were loose.
Пікірлер: 203
@jcarne101511 ай бұрын
I recently installed the most expensive BCG I’ve ever bought for a personal upper. Hand cycling revealed unusual resistance going in and out of battery. I tried a much less expensive BCG, no problem. I borescoped the interior of the carrier, and found not only significant tool marks in the gas ring bore, but significant burrs inside the gas relief ports. It’s going back to the manufacturer.
@wyattjones74833 жыл бұрын
It's like Déjà vu all over again! I can say without a doubt my two Young Manufacturing BCGs have run flawlessly after the SOTAR treatment.
@jdecar12 жыл бұрын
How does one go about having SOTAR Chad examine a bcg? I can't find it on the website or fb. What's that cost, anyway?
@justsnuggle2 жыл бұрын
I would love to see your recommended parts list for replacement parts and what you think about bolt carrier coatings.
@enb3810 Жыл бұрын
He did, recently. Check his page
@mayhemgarage96728 ай бұрын
@@enb3810where?
@willo77342 жыл бұрын
You mentioned it in the video but I’ll repeat it. Your wife is a really good camera operator. Great views on all of the details.
@SchooloftheAmericanRifle2 жыл бұрын
Thank you. In my opinion she is the star of the show. My videos were terrible till she stepped in.
@thatrealba3 жыл бұрын
"Don't do this at home." Yeah, cause I have a bench full of gauges at home like that. 😅
@HB-kp6rl3 жыл бұрын
Call brownells and start collecting. Can’t hurt, right?
@Balticblue9326 күн бұрын
@@HB-kp6rl I wished he had an entire list of the tools he uses on his bench that we could either buy a full set from him or each one linked to where it can be purchased.
@kenneththynes4761 Жыл бұрын
These videos are outstanding. I have multiple armorer certs from Glock, LWRC, HK, and FN, but these are incredibly informative and cover minutiae that I'd never received on the AR. And yes the camera work is really good.
@southernviking31133 жыл бұрын
Off topic of the video but whenever I’m cleaning one of my ARs or building one, swapping parts or whatever I’m doing I love to just hit play on the playlist and listen while I’m working. I’m not listening to videos regarding the work I’m doing, I just like to listen to Chad while I’m working on my rifles.
@BrassAngels Жыл бұрын
Thanks to Ms. Donna for the stellar camera work! Thanks also to Chad for putti g this jazz o line for those of us, 2A supporters, to learn from the best!
@TheWinterfan3 жыл бұрын
Love Love Love these types of vids. Please keep em coming and thank you for making them.
@jonwick46283 жыл бұрын
Thank you for the great content. Very informative. Best format on KZfaq.
@boinger19883 жыл бұрын
YAY! new autopsies... been waiting for some new content. keep up the good work
@Tom-qx5nl3 жыл бұрын
Another excellent video! No issue with audio. Thank You so much for sharing your knowledge, it is most appreciated.
@ThePatriotParadox2 жыл бұрын
Absolutely love this video, a lot more in depth into the gun smithing/machining side. Love to know how everything coexists together and how everything is made, also what it's made of (for best performance) I so wish I could be a young squire to you and absorb the vast river of knowledge in which you covet concerning the Riffle "WE" love as Americans.
@lyndalolson30672 жыл бұрын
Also so enlightening...you do an excellent job at teaching! Thanks
@andrewbrought72213 жыл бұрын
Great video & terrific content as always! Thanks Chad & Donna.
@ltgoogle37302 жыл бұрын
So I read YM statement on screw staking... it doesn't actually say why they don't stake. It just says we don't do it, here's what mil-spec calls for, and here's what we. Should you stake it, we won't warranty it. None of that really answers the question of why they don't do it though
@vg17012 жыл бұрын
The don't stake cause it's easy to do improperly. So instead they have a key built into the gas key that fits a special recess in the carrier. That lines the parts up correctly and carries the loads of the gas key and gas tube slamming together. Then the actual screws are loctited in place
@joshr22803 жыл бұрын
These vids are so satisfying for some reason. Wish he d have a page that ranks all the bcg s . He should almost buy which ones he thinks best then put the parts on it he likes , then sell them. People always will pay for the best
@209brandonb3 жыл бұрын
The problem is the best that day might be the worst the next batch these are just that particular one. Watch the vids when he does like 5 of the same manufacturer and they all gauge different. Just get a colt bcg and know ur good. They don’t look fancy with DLC or TN coatings but they are not gonna fail on ya and always gauge good! He gauged 3 from almost 30 yr apart and still gauged good.
@DerWaidmann_3 жыл бұрын
He always says it's a sample size of one and just because one sample is bad or good doesn't mean every copy will be that way
@donjohnson51722 жыл бұрын
Blindly buyin stuff just because “Colt” can get you into just as much trouble. Tons of Colt stuff out there that’s out of spec and junk. Hell, they hardly make ANYTHING in house anymore.
@savvycivvy56443 жыл бұрын
I love your videos, I have learned so much and am excited to continue learning. I hope I will have the opportunity to own and utilize a majority of the tools, gauges, and devices you use. Thank you and your amazing wife for providing such wonderful content.
@ThePatriotParadox2 жыл бұрын
Also must compliment you're wife on the camera work, really good at showing what is needed to see and staying with you're work and not staying off. I know my girl would've already got fed up with me and walked off...lol
@TylerO_O.3 жыл бұрын
love your content . big thank you for teaching me so much... I'm a hobbyist I'd love to be high caliber (hhaha) in smithing and all the things you're teaching... I build out rifles but I'd if there's much of a market in my area for these skills. Oh well at least I can live vicariously though you!
@actionjksn Жыл бұрын
I bought my BCG a few years ago at a gun show and the only thing I knew about inspecting it was the staking. It's a no name brand made in a small shop somewhere in Ohio, the guy I bought it from for $150 couldn't give me any information either. Now that I've been watching these videos and know what to look for I have taken mine all apart and examining everything. I can't believe what I'm seeing! Everything I look at based on these videos looks freaking awesome. This thing is so good and the machining inside is excellent. I'm not sure if it's Chrome plated or nickel boron, the color looks similar to the ones in this video but I'm just not sure. The bolts and extractor are black. The sides of the bolt carrier have that kind of cool looking faceted shape. What I do know is everything looks really good. I am thinking about ordering some of those Springco springs though, just for good measure.
@don201902 жыл бұрын
Fantastic vid. I have learned allot from you. Thank you so much for doing these. I thought Young Mfg didnt do staking of the screws because the used a recess in the carrier that an extended slot from the gas key fit into...I didnt see that on either of these two carriers.
@mattfleming863 жыл бұрын
Glad to see the pros use a cordless drill as a lathe as well.
@brianfitz32183 жыл бұрын
Glad to see you posting new content again. I'd love to take one of your armorers classes down the road
@williamboulanger36393 жыл бұрын
Really ? - "a couple " AR's You did mean a couple thousand + !!! Great info as always thank you.
@SchooloftheAmericanRifle3 жыл бұрын
I'm surprised anyone caught that. Good job.
@toshmiller55713 жыл бұрын
Thanks for all the knowledge Chad!!!
@Balticblue9326 күн бұрын
I wished you had an entire list of the tools you use on the bench that we could either buy a full set from you or each one linked to where it can be purchased. I would buy them up for sure.
@lawrenceaiello6561 Жыл бұрын
Just found your classes and think they are incredible and very helpful. I would love to know where you found all those fantastic gauges and where I can purchase them?
@lordofwar20062 жыл бұрын
Time stamp 33:26 what size pin gauges are you using for the gas key ? I started make a gauge pin setup like your I've got most of the pins just a few left and i have to make the Stand for the bcg bore pins and the pin handles im getting there
@brianfitz32183 жыл бұрын
Fantastic video! I bought the Sinclair bolt vise based on a previous video you put out as well as numerous other armorers tools because of what I've learned watching you. I consider myself a hobbyist with aspirations to become an armorer someday. I would love to know where you source all your gauges, spare gas keys, springs, etc. I used to subscribe to the belief the AR was just Legos for Adults because everything is labeled "MilSpec". I can now fully appreciate what you refer to as "Tolerance Stacking" as I've encountered varying issues with both fully built ARs as well as ones I'm building from stripped lowers. You're an invaluable resource to guys like me. Thank you for the videos. Also I have to admire the great camera work by your wife
@iamnotpaulavery2 жыл бұрын
I know. *I've got to get me a set of the gauges he uses!!* I've encountered the same issues as you did after putting together 6 ARs. The AR is the "Rolex" of rifles, with many parts that have to work well with the others in order to extract as much precision as possible. The AK is a Timex!
@dmdm9198 Жыл бұрын
@@iamnotpaulavery where did you buy your guages from?
@iamnotpaulavery Жыл бұрын
@@dmdm9198 No, *I wish* I had the gauges he has. I don't have any specialized gauges.
@BareSphereMass2 жыл бұрын
I would love to see LWRC and POF BCG Auatopsy!
@333Kdigital3 жыл бұрын
You have some of the same stuff you would find on an aerospace and electrical engineers bench.
@dgr12393 жыл бұрын
It would be amazing if you did an analysis of the “new” Colt cr6920.
@Mr_Clean3 жыл бұрын
Small arm solutions channel did a pretty good interview of the CR 6920 versus the Le 6920 if you haven't seen it
@fredsmith97882 жыл бұрын
I recently saw an advertisement for nitrided gas keys that were metal injection molded. Can mil spec gas keys be MIM, or should they need to be machined from billet steel?
@bmphil340023 күн бұрын
All these checks and possible corrections do make me think the AR is a pretty delicate machine to keep running correctly......
@TylerO_O.3 жыл бұрын
can we get videos on other weapon systems soon too. Not just m16/ar15s? I would love to see some stuff on blowback, roller delayed , radial delay blowback actions, maybe even stuff with revolvers and timing etc.
@SchooloftheAmericanRifle3 жыл бұрын
That's not in the cards. I stick to just this weapon system. I have over 150k invested in gauging, inspecting, testing, and teaching just about the AR family of weapons.
@Nemesis4x43 жыл бұрын
As always great camera work. Thanks to both of you.(Erick Foor)
@onna-day70473 жыл бұрын
@Nemesis4x4 Thank you! ☺️
@anthonyconner3513 жыл бұрын
Thank you for all the great content! I had a couple of quick questions if you have a chance. Do you prefer a phosphate BCG over nitride? Is one coating better than the other?
@BombproofCraftsman2 жыл бұрын
Phosphate is old school, nitride is a more modern coating. Phosphate is porous and will hold lubricant, but it’s also more abrasive. Nitride is non porous & smoother. I personally prefer a slick coating on a bcg, they require less lubricant to operate smoothly. My favorite has always been a polished hard chrome, they will run even when dry If things are clean. And a bonus to a slick bcg is that they are easier to clean, carbon wipes away easily. And that’s the down side to phosphate, the porous nature traps carbon.
@michaelhart9463 жыл бұрын
Chad have you or are you going to do any comparisons of left hand to right hand bolt? I'm curious if there is an actual difference between left hand bolts and right hand.
@nolanmcevoy25472 жыл бұрын
Is the quality of the post KE buy out BCGs the same as the OG YM BCGs. I’ve been thinking about getting one but I know that sometimes when a company changes hands the quality can end up diminishing.
@GreatMercenary2 жыл бұрын
Well I own 2 and so far so good. I haven't ran more than 2 or 3 mags in a row to see if the carrier screws come loose, but I can get them staked later on if I need to. They are kind of pricey, but they are chrome and it's supposed to be the best for BCGs.
@navywolf17532 жыл бұрын
No.
@capbyrd013 жыл бұрын
"chuck it up in your drill" I think mean my poorman's lathe.
@DACFalloutRanger3 жыл бұрын
I've missed these videos 🥺
@chipsterb49462 жыл бұрын
Whoa! I did not know that the ejector roll pin needed to be replaced each time you remove it. Is that specific to this part or roll pins in general?
@MarkiusFox3 жыл бұрын
"That's your HOME! Are your too good for your HOME?!?!?!"
@jammbbs16883 жыл бұрын
Thank you for more videos
@NoWr2Run3 жыл бұрын
T.Y. for sharing your knowledge, SIR. GREAT CAMERA WORK ALSO.
@onna-day70473 жыл бұрын
@nowr2run Thank you! ☺️
@NoWr2Run3 жыл бұрын
@@onna-day7047 Well he couldn't have made such GREAT VIDEO WITHOUT YOU. I GIVE CREDIT WHERE CREDIT IS DUE & YOU'VE EARNED MY REPLY. It's a TEAM EFFORT making these WONDERFUL VIDS.
@ranchhandrandy32132 жыл бұрын
Why do you prefer the insert to the o-ring? Also, where can I source a set of those gauges?
@davessparetime83 Жыл бұрын
I built a 7.62x39 AR-15 and it wouldn't go into battery. So after watching this video I looked at the extractor and it was stiff. Not much spring back. So after taking it off I found the spring laying sideways causing the issue. Thanks
@romeoechofoxtrot18 Жыл бұрын
Great video but the question I have is are these bolts magnetic particle inspected and high pressure tested?
@donjohnson51722 жыл бұрын
Young ought to be ashamed of themselves man. They thru all this bullshit posturing to state why they DONT stake their key screws, and then our boy breaks them loose with very little effort. For what they charge for those things, you’d think they’d make damn sure that they are torqued down and thread locked. If you aren’t gonna stake and you’re gonna make a big deal about not staking, you can’t stick your foot in your mouth like this.
@vg17012 жыл бұрын
These aren't new out of the box so it's really not right to say for sure.that this is a manufacturing error. Really they look like someone took the gas keys off before in the past and didn't do the proper diligence in reassembling them.
@ETC_Rohaly_USCG3 жыл бұрын
Even though I don’t have a set of Go/NoGo gauges, thank you for at least mentioning the dimensions... I can at least get a rough estimate of my dimensions with my calipers and one day, I hope to have as awesome of a bench as you. *Edit* With all of the tolerance stacking that can occur with COTS parts, at least I can match up various parts better, to get at least “mil-spec” fittings, lol!!! “If the term ‘Mil-Spec’ excites you, you have obviously never served in the Military” lol
@YNTGUNS Жыл бұрын
I just had a new barrel put in my colt m4, and I'm using my old m4 bolt and carrier, is this a problem? Do I need a new bolt? 4500 rounds thru the bolt.
@jackjmaheriii3 жыл бұрын
I just received the non-NM BCG…. I’m sweating bullets!
@Gunner-733 жыл бұрын
About the YFS fasteners... what screws do you recommend and where do you get them ?
@edwinlongwell3 жыл бұрын
OCKS screws. There are a few online retailers that carry them. Just google it.
@iamnotpaulavery2 жыл бұрын
I have a Young BCG that I want to use in my AR. Do you suggest making the same mods? Who makes the replacement springs you used, btw?
@wirebrush2 жыл бұрын
Springco is what he stated in the video.
@sackychin62673 жыл бұрын
I never understood young’s claim that use of permatex sealer is a replacement for staking
@williamthompson92622 жыл бұрын
I noticed you haven’t done an HMB bolt carrier… I have one that needs a physical
@Eroc5563 жыл бұрын
How do we get things setup to send in? I have a couple barrels that would be great to see pass/fail??????
@blip_bloop3 жыл бұрын
I also am curious I have an Anderson chrome BCG that is from a bad batch a few years ago, that I'd be curious to see autopsied.
@martinandrews84962 жыл бұрын
I can't find where u get those coil spread my pins. What size are u buying? Are u cutting a bigger one down.
@tee.jay.e2owboyp-dro3643 жыл бұрын
I'm in the process of shopping for a new 5.56 bcg & can't decide on what to get. What brands would you recommend? If you can recommend some.
@209brandonb3 жыл бұрын
Just get a colt and know ur good.
@tee.jay.e2owboyp-dro3643 жыл бұрын
@@209brandonb Oh yeah. Colts tried & true. 👍🏼
@Chris-wp3ew2 жыл бұрын
Are you using a generic shop barrel when you do the headspace tests? I see you tried both bolts with that one (generic?) barrel. I "thought" the headspace test was for a specific bolt and a specific barrel? Along the lines of a matched set. Please educate me. Perhaps I'm making this more complicated than it needs to be.
@wildlandoutdoors512 жыл бұрын
Curious where you got all your gauges from???
@benfrank15833 жыл бұрын
Have you ever checked out a Franklin armory rifle?
@StrideResearch3 жыл бұрын
Need one of these for my Lantac enhanced carrier
@HB-kp6rl3 жыл бұрын
Can i send you a Stag semi auto bcg? I bought the gun in 2009 and have less than 1k rounds on and its basically trash. Ive got an Aero Precision bcg I’m going to either replace of sell the whole gun. It’s way over gassed and still functions with worn out gas rings. Ejects to the 12:30-1:00. Might just send tou the whole gun as a blast from the past kinda thing
@justsnuggle2 жыл бұрын
28:00 super tip of the day. Things I wish I knew 10 years ago. Some guessing trying to clean all the carbon out of the ledge where the gas ring transitions to freebore is not that important.
@martinsonofwar3952 жыл бұрын
"Don't do this at home" 😂 made me chuckle
@kruelzombieful Жыл бұрын
Will those springs work for an 7.62x39 ar bolt ?
@uniquebassin72062 жыл бұрын
Where can I buy these tools you use to check the tolerances?
@sultros2 жыл бұрын
I have a general question about BCG operation I'm hoping someone can answer. This is in regards to an Aero Precision M5 BCG. Should the firing pin ever strike the primer during cycling / feeding / doing BCG things not involving using the trigger? For example: From the open bolt hold position, a magazine a loaded, the release is pressed and the BCG moves forward, loading a round, and going into battery. Without firing, the charging handle is pulled back ejecting the unfired cartridge. Safety is on. I discovered a shallow but clearly defined strike from the firing pin. Is that normal?
@TMega56122 жыл бұрын
Yes. The firing pins in most modern rifles do not have internal firing pin safeties or springs preventing them from hitting the primer. ARs and AKs do it and it's pretty much never a problem.
@trivium092 жыл бұрын
It’s normal, especially with AR-10s in my experience.
@chloedemeter54732 жыл бұрын
It's normal but it's also part of why military uses such hard primers. While it's rare slam fires have occurred. Especially in AR-10 and 7.62 x39 ARs with heavy buffers and buffer springs. I've had the latter happen once and a buddy had an old Colt AR set off a round while loading his HD gun in his kitchen. Always keep that muzzle pointed in a safe direction.
@sultros2 жыл бұрын
@@chloedemeter5473 Really apprecaite the feedback and couldnt agree more on your last point. Thank you.
@williamthompson92622 жыл бұрын
My young hmb bolt failed the gas ring test new out of the box.. it shoots fine but man makes me worry
@dothwalrus370 Жыл бұрын
Gas rings are cheap, replace them and move on, though that is disappointing. A lot of companies seem to have let their QC down to meet demands.
@shadowfoxcorp3 жыл бұрын
Are you ever going to finish that colt 601?
@SchooloftheAmericanRifle3 жыл бұрын
Yes. We do not have an ETA at this time due to our class schedule and other commitments such as gauge orders, repairs, and consult work.
@KnifeCursed3 жыл бұрын
I’m somewhat confused by your use of a dremel to hand grind the extractor spring pocket. Why not simply try another spring or two or try a bit harder to install the spring? Seems super wecsog to grind away like that with no gauging of the extractor spring pocket diameter, depth, or spring size.
@goinhot91333 жыл бұрын
Honestly I wondered the same, try another spring to see if it’s the spring or the hole. Hopefully he sees this and fill us in.
@SchooloftheAmericanRifle3 жыл бұрын
@@goinhot9133 I have several go and no go gauges for the extractor pocket. Each gauge is based on the spring used due to spring dimensions. I use 4 different gauges. I don't show everything on videos. I also cater my instruction based on my audience. For what it's worth, I have never opened a spring pocket excessively using the method shown in the video that resulted in the extractor not capturing a Colt Gold or Sprinco Spring. If I did or mistakenly do so in the future, I would replace it on my dime. I have a bin of TDP Spec Extractors. The extractor spring pockets on extractors are often too small for a proper Colt Gold Extractor Spring or 4/5 Coil Sprinco Springs without using excessive force. Excessive force can diminish the life of the spring. The fix is what I showed in the video or you can replace the extractor. Better have a lot of extractors on hand if you take that approach because most are undersized. Armorer's usually replace things that don't meet their standards, Good Gunsmiths can make changes. I'm both.
@goinhot91333 жыл бұрын
@@SchooloftheAmericanRifle thank you for the long response, just trying to learn. Wasn’t doubting what you did, I knew there would be a reason. Thank you for the informative reply.
@lokiwartooth11383 жыл бұрын
@@SchooloftheAmericanRifle what dremel pig tail are you using? I like the metal
@MidwestSurvivalCompany5 ай бұрын
Where do we get all these gauges
@nicg95993 жыл бұрын
Did the national match cost more? Kinda poor qc on their part, right?
@stefanmolnapor9103 жыл бұрын
Sound is good on my end
@333BlkFlagg7 ай бұрын
❤❤❤❤ saint chad
@TylerO_O.3 жыл бұрын
triple 6 the demon carrier
@beekeeper84749 ай бұрын
Do you do 308 bolts?
@ethan5.564 ай бұрын
I have a young manufacturing bcg leaking gas on the left side of the carrier key. Young manufacturing told me to re torque the gas key screws to 56 inch pounds and it the leak continues they'll send me a return shipping label
@2of2DCH3 жыл бұрын
Dude you're seriously a national treasure. Appreciate the heck out of you for making these! Edit: huh those carriers do not have the tab & slot gas key setup
@JimJones762x39 Жыл бұрын
What brand of gas key screws is he using @ 32:40?
@NoWr2Run7 ай бұрын
OCKS
@JimJones762x397 ай бұрын
@@NoWr2Run 👍 thanks man
@tech62633 жыл бұрын
I have missed your video’s. Scratch Rebels ear.
@ceezedgerman2 жыл бұрын
What's the point of beveling the ejector?
@chloedemeter54732 жыл бұрын
My last response was in more detail but basically it prevents or at least vastly reducing peening and edge roll. Also chipping of the edge which can lead to longer cracks. Look into impact ends of tools like chisels and why/how to prevent mushrooming. The impacts against the cartridge can have the same effect on the extractor. Which can either break it or make it get stuck inside or outside of the hole it's supposed to drop into.
@onpsxmember3 жыл бұрын
A general question to the extractor donut/spring use: If both are used, does the donut (o-ring) reduce ingress of dirt in the space of the spring? Is the potential problem that the donut gets in the way of the spring when damaged?
@heathturnbow39223 жыл бұрын
Thanks for the video. What bcg would you recommend as a premium bcg? Thanks for any advice!
@theduck173 жыл бұрын
Microbest seems to be a solid BCG. Toolcraft is a mil contractor so they'd be a good choice too. Daniel Defense makes theirs in-house and I've had good experience with them as well.
@musician4453 жыл бұрын
Every manufacturer has the potential to put out lemons. Thats just how manufacturing goes. Even CNC machines are only as good as the bits they are using to cut the metal. Or as good as the imperfect human that calibrated the machine. When you look for a quality BCG, the consensus seems to be to look for companies with better reputations and better QC so that you have a better chance of getting a good part. But that still doesn't mean you're 100% guaranteed, its just a better chance. Best way imo, is to go with a good brand - BCM, Sons of Liberty Gun Works, Forward Controls Design, Daniel Defense, Microbest, Toolcraft, etc and then watch some more of Chad's BCG physicals and do some at home tests. In several videos he explains some at home ways to "gauge" your parts without actually having the precision gauges on his bench. Also, like he said, make sure that the part mates well with your build, make sure parts are not fitting too loose, or too tight. They could fail a gauge test, but mate well with the intended parts in the gun, because there is a spectrum of sizes that components fall into. I would also recommend getting a plain milspec style carrier. There are "enhanced BCG's" available that have modified components or dimensions that are designed to enhance reliability, but the application is far beyond what many people need. Although the enhancements are nifty and can genuinely do what they state, a well built "mil-spec" BCG will work great and last thousands upon thousands of rounds. The parts are more common and with proper maintenance and inspection, the carrier itself will probably last a lifetime even with incredibly high round counts. Sorry for the book, I just felt compelled to elaborate. I hope this helps.
@realisrealite55543 жыл бұрын
I have two Colt m4a1socoms a Geissele Urg-i complete clone on a Aero gen2 lower and a Dsa,Geissele,FN barreled upper on a Aero m4e1 lower.They all have Colt bcgs and are 100% reliable.With that being said there's levels of quality but junk is rare nowadays.
@sackychin62673 жыл бұрын
Lmt, Daniel defense, bcm.
@sackychin62673 жыл бұрын
@@theduck17 eh Toolcraft only makes carriers in house. From what I’ve heard, their bolts are subpar.
@muddyhotdog41033 жыл бұрын
I would've tried another extractor spring before dremeling material away on the extractor.. The one spring could've just been on the large side, and now when the spring is replaced in the future the next one might fall out easily because material was taken away that can't be put back.. Oh well, both cheap parts; but the spring is definitely cheaper (and probably more likely to be out of spec).
@SchooloftheAmericanRifle3 жыл бұрын
I have several go and no go gauges for the extractor pocket. Each gauge is based on the spring used due to spring dimensions. I use 4 different gauges. I don't show everything on videos. I also cater my instruction based on my audience. For what it's worth, I have never opened a spring pocket excessively using the method shown in the video that resulted in the extractor not capturing a Colt Gold or Sprinco Spring. If I did or mistakenly do so in the future, I would replace it on my dime. I have a bin of TDP Spec Extractors. The extractor spring pockets on extractors are often too small for a proper Colt Gold Extractor Spring or 4/5 Coil Sprinco Springs without using excessive force. Excessive force can diminish the life of the spring. The fix is what I showed in the video or you can replace the extractor. Better have a lot of extractors on hand if you take that approach because most are undersized. Armorer's usually replace things that don't meet their standards, Good Gunsmiths can make changes. I'm both.
@actionjksn Жыл бұрын
@@SchooloftheAmericanRifle Some people are scared to death of voiding a warranty. If you and the owner of those bolt carrier groups took that approach, that guy would still have two unstaked bolt carriers and his crappy screws would still be loose.
@glocksundgeworfenheit_ Жыл бұрын
Must be an inexpensive shop because you could buy a new bolt for a few more hours of labor on this one
@ared66563 жыл бұрын
Young's whole justification for not staking is that properly torqued screws shouldn't come loose. If that's their claim, I'd damn sure expect them to torque right and seal the key. Seems like a lot of extra work for an expensive BCG.
@justsnuggle2 жыл бұрын
Why should the ejector be rounded
@chloedemeter54732 жыл бұрын
Same as why the ends of punches and chisels should be rounded or chamfered. The squared off edge can peen and roll over. For this part it can causing a lip that can either prevent the extractor from being able to slide into it's hole or make it get stuck in there. Can also chip more easily and be the introduction point to longer cracks. Considered the conditions it operates under it's very much in a similar position to a chisel handle. The constant impacts while stripping and seating rounds is much the same. Really, look into chisel and punch handle geometry and why/how to avoid "mushrooming" of the end that's struck with the hammer if you're interested in seeing a lot of detailed breakdowns and images of the effect. That's probably the most common source of info on it. That's where I first learned the concept.
@heyhayhay247 Жыл бұрын
The nitpicking is painful
@peeeoii2738 Жыл бұрын
Bolt face spec?
@johnwool8 ай бұрын
OPTIMIZED CARRIER KEY SCREWS; thank you for NOT using Torx fasteners.
@benfrank15833 жыл бұрын
Would you recommend the POF USA BCG? I can't think of one better
@benfrank15833 жыл бұрын
@DVCasey0311 it's made by pof-usa mad scientists and has a bearing roller cam. Anything to reduce friction. Plus how it's made and treated
@sackychin62673 жыл бұрын
I don’t recommend the use of the roller cam pin in a non external piston ar
@Mr_Clean3 жыл бұрын
@@benfrank1583 did Eugene Stoner use bearing roller cams?
@benfrank15833 жыл бұрын
@@Mr_Clean nope. It's modern shit bro.
@benfrank15833 жыл бұрын
@@sackychin6267 can I get a reason please
@surgetsann3 жыл бұрын
Yikes. Going DD for chrome in the future.
@GreatMercenary2 жыл бұрын
Looks like Daniel Defense discontinued their chrome BCG. Too bad because I would have liked to have one to try out.
@kylesprengeler59652 жыл бұрын
these videos literally make me paranoid about even my $1500 ARs, anyone else have the same vides?
@bobbyc27682 жыл бұрын
pause at 16:50, does anyone else see what looks like an old person's face in the palm of his hand?
@seanschweitzer59353 жыл бұрын
Algorithm boost
@CertifiedBullpupHater3 жыл бұрын
Hey guys if anyone sees this and could help I would really appreciate. I’ve recently assembled my first complete upper. (SOLGW NOX, 13.7 barrel, gas block, Aero upper receiver and gas tube, bcm bolt, gieselle sch). This is on a lower with a sprain I blue spring and h2 buffer. For whatever reason when I shoot it if feels pretty soft and yet shoots a lot of gas in my face, like my bcm 11.5 suppressed shoots softer and has less gas blowback to my face. So I thought the barrel just had a really wide gas port (which is weird to me because it’s a Sons barrel)….but the thing is ejecting consistently at 4:30-5 o’clock…so it doesn’t make sense to me that it would be over gassed. I threw my sandy S on it and it felt like I stuck my face into the exhaust of some gas guzzling vehicle. Any ideas what is going on?