I hope you found this overview helpful! If you have any questions or would like other tips/tricks, just let me know in the comments or join us on Discord.
@dannyhayden425Ай бұрын
This man, company, whatever is saving my life right now lol I got a 3 Pro from a buddy and have spent a week trying to get this damn thing to print. I stumbled across these videos yesterday and got benchy printing right now. It's the most successful attempt I've had so far thanks to this dude. Thanks guy
@3DPrintscapeАй бұрын
Hi. Im glad that i could help out :)
@IsmailQadry2 жыл бұрын
These are legit the best Ender 3 guide/tutorial videos hands down, no question, full stop!
@3DPrintscape2 жыл бұрын
Hi. Thanks i appreciate the feedback :).
@serupjones6450 Жыл бұрын
your custom firmware video saved me thousandds of headaches and this is jst the iceing on the cake def gna sub keep up the great tutorials !
@3DPrintscape Жыл бұрын
Glad I could help :)
@BrAiNfReEzEv2 Жыл бұрын
Love your videos. Absolute legend. I about quit 3d printing until I stumbled on your videos. Thank you
@3DPrintscape Жыл бұрын
Hi. Thanks for the feedback, im glad i was able to help :) .
@lenrobinson13 жыл бұрын
Nice videos, the explanations are thorough, clear and concise. Zooming in to show detail helps while explaining makes the videos easy to follow. Thanks for your help with the Ender 3 Pro.
@3DPrintscape3 жыл бұрын
Awesome, thanks for the feedback :).
@denduro52 жыл бұрын
Just completed wholesale upgrade to my Ender 3 Pro printer (dual Z, DDX direct drive, 4.2.7 mainboard, BL touch) and needed help with the calibrations and firmware. This video was a huge help, and even better than that was the pre-configured firmware on your website. I hope others needing help and guidance find this video. Thank you!
@3DPrintscape2 жыл бұрын
Hi. Thanks for the feedback and your welcome.
@antoniorios3856 Жыл бұрын
Dude, your videos are great helped me configure my first firmware, and get my cr touch workign properly. Keep up the great work.
@3DPrintscape Жыл бұрын
Glad I could help
@1augh0utL0UD2 жыл бұрын
This is so helpful! I'm brand new to 3D printing (not quite a week in) and this is the thing I've been so confused about. Hopefully it's all smooth sailing from here.
@3DPrintscape2 жыл бұрын
Glad it was helpful!
@pablo123b3 жыл бұрын
Hi Rob, good to see you are safe and well, so you have now given me another project! stay safe fella cheers Paul from uk
@3DPrintscape3 жыл бұрын
Hi. Thanks for the feedback. It’s worth the extra effort to get the wizard and babystepping setup. It makes dialing everything in much easier.
@pablo123b3 жыл бұрын
@@3DPrintscape as the normal issue i have the btv3 2 and tft screen same as yours rob, but do you think i can find the update on github?....the answer is no lol
@3DPrintscape3 жыл бұрын
What can’t you find on GitHub? maybe I can try to find it.
@pablo123b3 жыл бұрын
@@3DPrintscape Thanks rob, i have the same setup as your ender3 pro with the tft35 screen, and bigtree tech v3 skr . If you could paste the link id really appreciate it
@3DPrintscape3 жыл бұрын
@@pablo123b I think this is what your looking for. github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware
@HelicoolsHelipad Жыл бұрын
Made a lot of sense, even to an old untrainable guy like myself. Thanks also for the other videos on this subject. If I had done my research before-hand, I probably would not have bought a BL Touch so soon into my experience level as a 3D printer. What a pain in the neck, but you made it work... so my hat it off to you!
@3DPrintscape Жыл бұрын
Hi. The bltouch is a pain to get dialed in and working but once it is it saves a lot of headaches down the road. Im glad i was able to help.
@michaelryan26223 жыл бұрын
Kudos to you for this video, ezabl died (flaky for a while now, nonresponse from th3d) , replaced with bltouch smart brand name, had to completely rework marlin skr mini software with your guidelines and it finally works, been messing with this for days, 3d printing for 5 years a lot and do all my own upgrades, your video is what I am looking for.
@3DPrintscape3 жыл бұрын
Hi. Thanks for the feedback, im glad i was able to help out :).
@darrelmiller6410 Жыл бұрын
Great job with this video. I just successfully implemented after static bed leveling. Thank you Rob!
@3DPrintscape Жыл бұрын
Hi. Thanks for the feedback.
@djtriggerfinger3 жыл бұрын
I tell you what the wizard for sure is a major timesaver. Great video man!
@3DPrintscape3 жыл бұрын
Hi. Thanks for the feedback and ya i love the wizard, it makes things much easier.
@sritri3 жыл бұрын
Thanks for another very useful video!
@3DPrintscape3 жыл бұрын
You're Welcome!
@dovfeder32532 жыл бұрын
Thank you for taking the time to create and release such great training videos! I am a total newbie (and at 66 years old that ain't easy) and have the Ender 3 Pro with the BLTouch. I am struggling with setting the Z-Offset and was excited to download and instal the bin file you created (thanks again) for the Marlin firmware 4.22 (though I'm not sure if I shouldn't try the 4.27 version) upgrade with the Z-Offset Wizard and the BabyStepper. I copied it to a SD card and it installed wonderfully. However, the printer locks up when I try to instantiate the Wizard with "Homing XYZ" on the display. I need to power down the printer to get out of the menu. I was hoping you could give me some direction on how to address this. Again, your videos are informative, concise and usually on a level I can just start to understand. Thank you again. -Dov Feder
@3DPrintscape2 жыл бұрын
Hi. Thanks for the feedback. If you run the autohome before initiating the wizard does it work right? Im thinking it may be a bug in the firmware.
@ddfeder2 жыл бұрын
@@3DPrintscape I tried that but it still locks up.
@3DPrintscape2 жыл бұрын
@@ddfeder What board do you have?
@dovfeder32532 жыл бұрын
@@3DPrintscape 4.2.2
@3DPrintscape2 жыл бұрын
@@dovfeder3253 I havent seen this happen in my testing, so it could be a number of things. It maybe worth trying the latest release in the bugfix line.
@TropicGrenadeLPTV Жыл бұрын
A warning! Pay attention to the correct pin assignment. Just because the colour sequence on the board connector is correct, i.e. blue, red, yellow, does not mean that it has to be connected in the same way on the probe side. In my case, the manufacturer had used a cable that starts with red, but then swapped it with blue at the board connector. This made me believe that the pin assignment was correct for the skr mini. When I turned it on, it quickly became apparent that the display was going crazy and the board smelled burnt. I was still lucky and quickly switched off. Although the board was a bit fried, to my surprise it still works perfectly. One more thing...If you use the z_end pin and the nozzle hits the print bed during z homing, then swap the pins on the z_end connector of the bltouch.
@3DPrintscape Жыл бұрын
Hi. Yes great advice. Its important to pay attention to the pins, not just the color of the wire. There have been many knockoffs out there with different colors/color orders that have caused issues.
@slgorin3 жыл бұрын
When I upgraded the firmware on the tft35, the z-probe offset want away and the p offset wizard showed up in its place. Shows a shim value and operates the same as the other. But my z-offset is acting up now. Do you know anything about the new wizard? Planning to redo the firmware to get it on the marlin side. That shim value makes me wonder if its adding or subtracting that .2 amount.
@3DPrintscape3 жыл бұрын
Hi. I will add a video to cover the new firmware to my backlog.
@carlosguimaraes80423 жыл бұрын
Very Good
@3DPrintscape3 жыл бұрын
Thanks
@Cosynq Жыл бұрын
Wish I'd found this a weel ago. Got the old Predator going with a SKR1.4 turbo.
@3DPrintscape Жыл бұрын
Nice
@Impuritan1 Жыл бұрын
I'm using your marlin build for Ender 3 with 4.2.7 board with BL Touch, except I have the CR-Touch. I can run through the wizard and use the baby-steps to get the test print dialed in, but as soon as I start a print it's printing in mid-air. I save the baby step value and add it to the Offset but I still cant get a print to work. Does the bed need to be leveled before running the offset procedure? Seems it defeats the purpose if so. EDIT: Went back and watched this again and I get a +000.7 but when its calculated I get nowhere near the -3.2 offset that you're getting. How is it calculating that number?
@3DPrintscape Жыл бұрын
Hi. The value should be a negative number and you should also level the bed before using the crtouch, though it shouldn't really impact the offset number. This video my help. kzfaq.info/get/bejne/o92Slcl02s2olZ8.html
@johnm.gerard1718 Жыл бұрын
One small question. I don't have a bed Probe. I thought that Pressing/selecting Store settings. Would make the settings persistent when you tun off the printer. Until you either Restore settings or upload new firmware. You said every time you turn off the printer you would have to repeat this process? What am I missing here? Thank You.
@3DPrintscape Жыл бұрын
Hi. If you store the settings they will persist through a power cycle. I just prefer to run the mesh at the start of each print to make sure its accurate. Things can change, the bed could get bumped, etc.
@Mossyfurnace3 жыл бұрын
So I thought I had babystepping set up but the z wizard is not adjusting for me. Worse yet I tried doing it manually and I'm getting super high numbers like freaking 9.9 did I compile the firmware wrong?
@3DPrintscape3 жыл бұрын
Hi. Something is definitely up, the z offset should be negative. What firmware are you running?
@mickyovts3872 Жыл бұрын
Hiya Rob, I'm using a robin nano v2 board on the ender and I have the wizard on and "working" but, once it homes and probes, it stays put, it won't move the nozzle to the centre, but my endzilla, running a 4.2.7(?) Board does could you help me please ??
@3DPrintscape Жыл бұрын
Hi. I havent used that board before but what firmware are you using with it, is your z stop connected, and do you have any other mods?
@febrezee69 Жыл бұрын
enabled the wizard and flashed the firmware but its not showing up on the touch display... any suggestions?
@3DPrintscape Жыл бұрын
Hi. Try to clear your eeprom.
@derm9734 Жыл бұрын
What can i do to make probe wizard appear on my screen. Also, when i try leveling with the bl touch, the motor keeps on going and it doesnt stop, how can i fix that?
@3DPrintscape Жыл бұрын
Hi. What axis isnt stopping and is the offset wizard enabled in the firmware?
@shahabazboss2 Жыл бұрын
Hi man, I configured marlin referring to your other video and am here to setup the z offset. I have issues with this, when I run Z Offset Wizard, Homing XYZ appears and it does that brings the head to middle of the bed and then z axis moves a bit up then the Bed leveler triggers couple of times and then the screen stays there for ever, how do I debug this ?
@3DPrintscape Жыл бұрын
Hi. You could connect your printer to the computer using pronterface and watch the console output. It should show you what’s going on.
@MinosMurdoc Жыл бұрын
I'm having some issues with the BTT Skr mini V2 + CR Touch, and found your video for that, but following your video for the z-offset. but i'm not seeing the offset wizard on either the marlin or btt mode of the TFT. Flashed the skr Mini to the latest firmware-bltouch. the TFT is running the TFT35-E3_V3-0.26 firmware.
@3DPrintscape Жыл бұрын
Hi. I think it was renamed to p offset in the tft.
@fkthewhat2 жыл бұрын
This was helpful thanks
@3DPrintscape2 жыл бұрын
You're Welcome
@Houtoriteit2 жыл бұрын
Why does my bltouch when I set it to zero crash into the bed but when I don't en I fix it with zo offset en get it tuned and it does an autolevel. Still does not can go True all 9 points on my bed. And sometimes the middle one where I set everything to?? Help!
@3DPrintscape2 жыл бұрын
Hi. It sounds like the wiring doesn't match the firmware. How is the bltouch wired and what firmware are you using? Also, to get it to probe all9 points, the g29 command needs to be added to the printer profile in cura, not sure if you did that yet or not.
@J1Billion Жыл бұрын
My wizard keeps gett stuck at "HOMING XYZ" and doesnt continue to z offest. BL touch only solid blue light/
@3DPrintscape Жыл бұрын
Hi. Is your z stop connected?
@christopherwhitcomb6233 Жыл бұрын
I did this step by step and it didn’t change my z offset. What could cause that. Doesn’t matter what number I set probe offset it still stays 0.7mm to high even after saving settings.
@3DPrintscape Жыл бұрын
Hi. Is the z offset value saving after you power off/on the printer?
@smail_mail Жыл бұрын
When my CRtouch is performing a bed level, the Y axis attempts to level just past the back of the bed. Can you give any insight as to why that may be?
@smail_mail Жыл бұрын
I figured it out. In a previous video of yours, you mentioned building the firmware and preprogramming the probe distance from the nozzle to X44, Y7, Z0. You also suggested that the viewer measure it themselves. I am dumb and don't know what that means. It turns out my Y needs to be 0 or so. Sorry for the confusion
@3DPrintscape Жыл бұрын
Hi. If its working i wouldnt mess with it but the y shouldnt be 0. That would mean the probe is right where the nozzle is on the y axis. I think something may be cached in eeprom that impacted the offsets/position.
@TotoGuy-Original Жыл бұрын
how can you home z if youve not setup the probe yet? or will it just trigger the probe as long as it touches before the nozzle?
@3DPrintscape Жыл бұрын
Hi. It will just trigger the probe when it touched the bed.
@aflyingcougar82907 ай бұрын
why is there no z offset wizard for printers that don't have a BL touch?
@3DPrintscape7 ай бұрын
Hi. Its because you dont set a z offset without a ABL of some sort. Its done by manually leveling the build plate.
@randallpatrickc Жыл бұрын
What is the 3d printscape msg scrolling across the bottom? I have the bugfix 2.0x f/w and I have installed the CR Touch and have connected to pronter. That’s all - can I use this wizard ok?
@3DPrintscape Жыл бұрын
Hi. It just part of the printer name. You should eb able to use the wizard without issues. If you dont see it, try to clear settings and check again.
@randallpatrickc Жыл бұрын
Under Probe Offsets I just have Probe X and Probe Y offsets (after reset config) - no wizard
@3DPrintscape Жыл бұрын
@@randallpatrickc What firmware are you using?
@HyenaZin Жыл бұрын
My z offset wizard doesn't start up when I click it . What did I do wrong ?
@3DPrintscape Жыл бұрын
Hi. Is it doing anything at all?
@jeffmlane3 жыл бұрын
Great video. If I can make one suggestion, please slow down and show the buttons clearly. Often you move to quickly and your finger obscures the name of the button you are pressing. This is all too common on touch screen tutorials. Thanks
@3DPrintscape3 жыл бұрын
Hi. Thanks for the feedback, i will try to focus on that more. Its surprisingly difficult to get both the screen and printer on camera at the same time lol.
@colenado Жыл бұрын
Your videos and website have been extremely helpful getting my CR touch to work with your custom firmware! I run into 1 problem though. For whatever reason the firmware on my old Ender3 Pro 8 bit board supported the M600 command but the new 4.2.7 board with your BL Touch bugfix firmware does not. Is there a way to enable this or is a different firmware version I can download?
@3DPrintscape Жыл бұрын
Hi. The m600 command is enabled but the filament runout sensor is not. That would require a custom firmware build.
@colenado Жыл бұрын
@@3DPrintscape guess I should have specified more. I used it to do color swaps for HueForge. Luckily TH3D'S build of the firmware added that support back into the 4.2.7 board.
@smail_mail Жыл бұрын
The Z-Offset moves slightly positive (+) every time I start a new print, unless I restore defaults for every print. Any ideas?
@3DPrintscape Жыл бұрын
Hi. Are you saying the values stored in the system change on power cycle?
@smail_mail Жыл бұрын
@@3DPrintscape Surprisingly, no. The Z-offset values will stay the same on the screen (Mine requires -0.2). This works fine the first print. When I go to print again, wheather its a few minutes later or a few days later and it doesn't matter if the machine is powered down or not, the Z-offset changes, but not visibly on the interface. It will only move slightly positive, maybe 0.02 or so, causing the nozzle to print slightly off the bed. Once I select "Restore Defaults" it goes back to printing correctly, but the next print I have the same problem, so I have to select "Restore Defaults" every time I start a new print. I still have the firmware on the SD card, so maybe that's the issue? Really wish Reddit wasn't going through it's blackout right now, there's a wealth of knowledge on there that I cannot access at the moment. Thanks for any advice.
@3DPrintscape Жыл бұрын
@@smail_mail Do you have any movement in the carriage or on any axis?
@smail_mail Жыл бұрын
@@3DPrintscape No, I was thinking that as well, but everything seems tight and secure. I think I'll just end up hitting restore defaults for every print, it seems to work fine, just an extra step. I do appreciate your help
@hamishpatel742 жыл бұрын
Great Videos! I hope you can help me with some trouble. I followed your other video about the SKR E3 Mini v2 and the BLTouch (and TFT35), and enabled the offset wizard, bltouch, etc. When I go to Menu -> Movement -> ABL, I don't see the same icons you have. the scroller in the center of the main menu does not say ABL Active, it says "Fade Height 10.0" My Icons from left to right : Top ROW -> ABL Deploy Stow Test Bottom Row -> Repeat Z_OFFSET BabyStep Back I am using the latest bugfix build as of 11/18/2021. Any help would be greatly appreciated!
@3DPrintscape2 жыл бұрын
Hi. What firmware do you have on the tft35?
@dinasupivi5361 Жыл бұрын
it,s happening the same to me, have you ever solved it?
@hamishpatel74 Жыл бұрын
@@dinasupivi5361 I ended up going back to the text based screen instead. the touch screen was a bit buggy. Since I use octoprint i rarely ever use the touch screen
@dinasupivi5361 Жыл бұрын
@@hamishpatel74 okay thanx
@shadowhenge71182 жыл бұрын
Man i wish that actually worked. The wizard always puts my printing starting up in the air.
@3DPrintscape2 жыл бұрын
Hi. It has worked out well for me. Did you save the settings afterwards. Also if you use baby stepping you will need to update the z offset to account for the value there.
@mitchb77 Жыл бұрын
My stock ender 3 nozzle always ends up higher up after i have done the Chep level gcode! What setting have i got wrong? It was working fine for months
@3DPrintscape Жыл бұрын
Hi. Is the carriage or anything moving around?
@mitchb77 Жыл бұрын
@@3DPrintscape Not that i can tell
@dannytech47092 жыл бұрын
Hi thanks for the video ! Can the z offset wizard be enabled with out a BL touch? I followed your video and check all the menus still I can't see the option
@3DPrintscape2 жыл бұрын
Hi. Based on the way the config file reads "#if HAS_BED_PROBE" must be true. So i dont think it can be used without the bltouch.
@emrysbatson31934 ай бұрын
my version x27 doesn't have wizard z offset, hell I am unable to find z offset anywhere.
@3DPrintscape4 ай бұрын
Hi. Was the firmware prebuilt or built by you? The setting to enable it is in the advanced config file and eeprom has to be cleared.
@emrysbatson31934 ай бұрын
@@3DPrintscape built by someone else and Thank you for the info!!
@Mr99ZK Жыл бұрын
I have a TFT35 and I noticed that in touch mode, the Z-Offset Wizard is not available, but it is available in the standard Marlin interface. Any idea why. The Wizard is enabled in the firmware.
@3DPrintscape Жыл бұрын
Hi. Did you upgrade the firmware on the tft35? I think there is also a setting in the tft35 config file for it as well.
@Mr99ZK Жыл бұрын
@@3DPrintscape Yes, I did though I did not have a ABL installed at the time. It has been a while, so I will have to go and take a look on how to do that again.
@Mr99ZK Жыл бұрын
@@3DPrintscape I looked in the config file, but did not really see anything related to the Z-offset wizard.
@3DPrintscape Жыл бұрын
@@Mr99ZK Is there anything in there for p offset or anything like that? I think they renamed it in the newer version of the firmware.
@Mr99ZK Жыл бұрын
@@3DPrintscape Yes, that is what I used. I can kind of figured that P Offset and Z Offset were the same.
@barryrsahrp3 жыл бұрын
Can you please tell me what version of Marlin is in your Ender 3 Pro. I have a recently purchased Ender 3 Pro with a BLTouch fitted and my firmware does not have the same commands as yours which makes this video almost impossible to follow. Are the Australian versions different to the Us versions?. I have the BLTouch Ver.4.2.2 with the 32 bit main board.
@3DPrintscape3 жыл бұрын
Hi. Im running the current Marlin bug fix firmware. I did a video that covers moving to it and is linked in the above but you will want to follow that guide first as the Z-Offset Wizard is not currently on the Creality firmware. kzfaq.info/get/bejne/prdnir2EuZ7XoZ8.html
@mattlogue13003 жыл бұрын
Shit
@peterberggreen78242 жыл бұрын
Hi Again - something I don't understand is where you find that Z-Wizard in the Marlin software the comes with the BL-Touch. Supposed to be in the software if you just : Restore Defaults - fine my software says restore failsafe, which is properly not the same. It would be so much easier just to run the Z-wizard, but where do I find it?
@3DPrintscape2 жыл бұрын
Hi. I dont think the z wizard is enabled in any of the Creality builds. If you want that, you will need to run a custom build of marlin.
@elnarutouchiha3 жыл бұрын
I'm having issue with homing when its homing it will continue moving the z offset all the way down until it hit the class bed and it wont stop. any suggestion ?
@3DPrintscape3 жыл бұрын
Hi. It sounds like the wiring doesnt match the firmware. How is the bltouch wired and what firmware are you using?
@joepetersen48933 жыл бұрын
I have the same problem
@elnarutouchiha3 жыл бұрын
3D Printscape I don’t have a bltouch I change my motherboard to the skr v2 and I currently on bugfix 2.0 marlin firmware. I post a video on my KZfaq if you would like to see the issue I’m currently having. Thank you 🙏
@3DPrintscape3 жыл бұрын
@@elnarutouchiha Gotcha, ya post a video somewhere that i can get to or send it to me on discord. discord.gg/Bu94EYVkrU
@BSwithBeales2 жыл бұрын
Life saver Thanks bro !!
@3DPrintscape2 жыл бұрын
You're Welcome
@WhereNerdyisCool Жыл бұрын
Thank you, I just updated 3 CR-10S machines to SKR Mini E3 v3 with the TFT35 I couldn't find anywhere how to utilize some of the new features in the new screen! (You might want to alter the video title to TFT35 ABL Leveling guide?)
@3DPrintscape Жыл бұрын
Hi. Thanks for the feedback, im not sure if changing the title would hurt rankings or not at this point but i could look at making a similar more generic version.
@WhereNerdyisCool Жыл бұрын
@@3DPrintscape content ideas! These displays are very popular. I haven’t a clue what many of the features are (yet)
@Pickle3122 жыл бұрын
How do you enable the wizard in the creality CR touch firmware? I don’t have those menus available to me
@3DPrintscape2 жыл бұрын
Hi. You wont be able to enable it in the Creality firmware. You would have to move to marlin and uncomment it in the config.
@Pickle3122 жыл бұрын
@@3DPrintscape Thank you, I ended up figuring it out from your videos. I now have the updated marlin firmware on my machine and was able to set my CR touch up thanks to your videos. Im surprised you don't have more subscribers, your tutorials are much more detailed than others I have seen without being overly too long.
@3DPrintscape2 жыл бұрын
@@Pickle312 Im glad you were able to figure it out and thanks for that. Hopefully, my channel will continue to grow :).
@MarkAmaro2 жыл бұрын
I don't have z probe wizard in my menus but I do have set home offsets but when I try that I get Err: too far
@3DPrintscape2 жыл бұрын
Hi. the home offsets wont change anything related to z offset for printing. What are you trying to adjust and what firmware are you running?
@HeadgyHog Жыл бұрын
What if I don't have a Z Probe Wizard in my version?
@3DPrintscape Жыл бұрын
Hi. You would have two options. 1) Get a version with it 2) set the z offset manually which works fine.
@deankq4adj1253 жыл бұрын
I followed your Feb video on setting up Marlin in which you gave the steps necessary to set up the BL Touch. However, after flashing my mainboard, I don't have the tune option nor the baby-stepping. Did I miss something in the Marlin config. Another great video by the way.
@3DPrintscape3 жыл бұрын
Hi. Those are both items that need to be enabled in the firmware. If they are enabled, try to clear your eeprom. I had a random issue where i didnt see the babysteppings settings during a print until i cleard that.
@snoozy7473 жыл бұрын
@3D Printscape offtopic question: what size usb thumpdrive are u using and how is it formatted? i cant seem to get mine working on my tft35 (8GB, FAT32)
@3DPrintscape3 жыл бұрын
Hi. Its a USB 3.0 drive, 16gb, and formatted as Fat32.
@snoozy7473 жыл бұрын
@@3DPrintscape thnx for quick reply mate. Love your plain explanation in your vids. Keep it up
@3DPrintscape3 жыл бұрын
@@snoozy747 You're Welcome!
@bobf35982 жыл бұрын
Shortcut to babystep, just double tap the button without having to go through menu.
@3DPrintscape2 жыл бұрын
Hi. Thanks for the tip.
@stevenkenny92702 жыл бұрын
Your videos always help when I have issues thank you. Have a issue now. Just installed a BL touch and the firmware from creality for my ender Pro 3. But it does not seem to have the wizard on this. Is there something i am not doing?!
@3DPrintscape2 жыл бұрын
Hi. The creality firmware doesnt have the wizard enabled. You can try the firmware from my site if you want. 3dprintscape.com/marlin-firmware-builds/
@Nubbs5143 жыл бұрын
So I did everything and my printer isn't displaying the Probe Offsets. So I'm hoping you can help me out, I double checked everything as well.
@3DPrintscape3 жыл бұрын
Hi. What’s showing up in the about screen?
@Nubbs5143 жыл бұрын
@@3DPrintscape Are you talking about the print info screen ? What's the discord you have for the channel may make this easier
@3DPrintscape3 жыл бұрын
@@Nubbs514 Ya info or about depending on the firmware/screen. Here is the discord link discord.gg/Bu94EYVkrU , its also in the description as well.
@Nubbs5143 жыл бұрын
@@3DPrintscape I'll get ya later tonight when I get off work on discord
@3DPrintscape3 жыл бұрын
@@Nubbs514 Sounds good.
@goin2cali4202 жыл бұрын
Ran the wizard but when I try to print the nozzle is too high. So frustrated with this thing already.
@3DPrintscape2 жыл бұрын
Hi. It may be worth making sure you don't have any excessive movement on the hot end carriage, x-axis, and bed.
@goin2cali4202 жыл бұрын
@@3DPrintscape I checked everything even loosened and tightened everything. About to give on this piece of crap.
@goin2cali4202 жыл бұрын
@@3DPrintscape thanks for your help I finally figured it out. Did what you said and just had to keep lowering it .1 mm at a time until it printed just right. Thanks so much.
@3DPrintscape2 жыл бұрын
@@goin2cali420 Awesome, I'm glad you got it working.
@MacS1ms2 жыл бұрын
Hello, I am on an Ender 5 Pro, I downloaded the right program on your site, corresponding to my printer, everything was fine except for the "Z-Offset Wizzard". Indeed, when I make this command, my screen is frozen on "Homing XYZ" and nothing happens... I let it run for a long time, but I can't access to the suite, what to do please, I'm desperate, I've been trying to install this thing for days. Thank you in advance !
@3DPrintscape2 жыл бұрын
Hi. Did you clear your eeprom after the upgrade, if not try that real quick.
@MacS1ms2 жыл бұрын
@@3DPrintscape Hello, yes I have the option "Initialize EEProm, and when I click on "Init" at the bottom right, I have a little "beep beep" that plays, and it returns to the main menu of the printer :/
@MacS1ms2 жыл бұрын
@@3DPrintscape I've just tried but nothing works, it stays frozen for hours, and I have to turn off my Ender 5 Pro and restart it to use it again :( OK, I download the BLTouch version (not BL Touch + Z-Homming, that work.. UPDATE : No, no way false joy, too bad I will continue to search for years on different sites the right solution to my problem, it bores me.
@3DPrintscape2 жыл бұрын
@@MacS1ms How is the bltouch wired and what is the exact board your using?
@bigdumbanimal233 жыл бұрын
I have the color screen. Had to load the V2 4.2.7 to get the screen to work. I was told that the Z-Offset Wizard wouldn't work with the V2 firmware. Is this true?
@3DPrintscape3 жыл бұрын
Hi. I havent tested it myself, but from what i was able to tell that is a true statement. There are a lot of Marlin features that wont work with the Creality screen.
@alphonsereitz Жыл бұрын
I've levelled, probed, z-off set.. but nothing works. The CR touch has throw me a for loop that I can not break out of.
@3DPrintscape Жыл бұрын
Hi. Does it autohome and run a mesh without any issues?
@alphonsereitz Жыл бұрын
@@3DPrintscape It auto home's okay. I'm still pretty new to printing, so I'm not sure what running a mesh is. Though I'm starting to wonder if my filament isn't just moist.
@3DPrintscape Жыл бұрын
@@alphonsereitz Did you add the g29 command to cura so it runs the mesh at the start of the print? It will probe the bed 9 times (3x3 grid).
@alphonsereitz Жыл бұрын
@@3DPrintscape I had not. I ran it through five runs of the probing, recorded each point, and averaged them. Turns out my bed is quite beautifully levelled. I found the real problem has been the extruder tension.
@rhondamaurer67822 жыл бұрын
I have followed all the steps you recommended but once it starts prints I don't have the baby steps. When it's not running I see steps/mm but as soon as it starts printing I can't raise or lower the nozzle. I have to start all over again. Baby steps would be great but they just aren't there. What do I do about that?
@3DPrintscape2 жыл бұрын
Hi. Try to clear the eeprom. If i remember correctly, it didnt show up for me until i did that.
@lakitu64222 жыл бұрын
@@3DPrintscape I am having the same problem. How do I clear the eeprom to fix it? I have initialized the eeprom is that the same thing as clearing it?
@3DPrintscape2 жыл бұрын
@@lakitu6422 It would be initializing it then i also do a reset defaults afterward. After that you want to save the settings.
@adnaandavis45292 жыл бұрын
Finally got my printer up and running again after honestly giving up. It's printing but I cant seem to set my z-offset on the TFT35, doesn't move after I increase or decrease values but baby stepping works. Could it be a compile issue?
@3DPrintscape2 жыл бұрын
HI. It could be but i would try to update the firmware on the TFT35 before doing anything else.
@jjsauer71252 жыл бұрын
nice guide. works for me ok (ender 3) but after adjusting with the probe wizard the next print sometimes the offset 1mm or so too high/low and I need to re-adjust. I assumed that it will stay fixed for all prints with the current filament?
@3DPrintscape2 жыл бұрын
Hi. It should be fixed. It sounds like you may have some movement on one of the axis, or the carriage.
@rayshort53282 жыл бұрын
Hi Rob, great videos, thanks to you was able to build Marlin firmware for my Cr 10 v2. But for some reason I can't go into negative numbers when setting z height... In Move Z, any suggestions? I read that you can enter a M211 S0 code to temporarily disable it, but not sure how to enter this. Please I need your help!
@3DPrintscape2 жыл бұрын
Hi. Thanks for the feedback. You can comment out #define MIN_SOFTWARE_ENDSTOP_Z in the firmware or use m211 s0 like you mentioned. If you want to use m211 you will need to connect the printer to your computer or an octopi, this covers that a bit kzfaq.info/get/bejne/ipeEe5OC1a66h6c.html. You may also be able to just create a g-code file with that as the text and run it on the printer like it was something you were going to print.
@AndrewAHayes3 жыл бұрын
Hi I installed the Creality BL Touch Kit, FW 1.1.6 BL Touch (Painful) and when I put the lid back on the heated bed would not work so I took it back odd and the bed heats ok, it was a real tight fit because of the pinboard, I initially managed to home and calculated the Z offset but this would not give a good first layer and now the Z offset will not work and I don't think the probe data is being used, I got so sick of it I ordered an SKR E3 MINI 2.0, will the Z Wizard work with this board and its firmaware?
@3DPrintscape3 жыл бұрын
Hi. Sorry to hear you were having issues but I think you will be happy with the SKR Mini upgrade. You can enable the z-offset wizard on the SKR Mini, thats actually the board i have running on the printer in the video. Here are two videos that may help kzfaq.info/get/bejne/rdqEacxynq-rZ3U.html & kzfaq.info/get/bejne/hrN3Z8V0nq-XdHU.html .
@kimpanattoni3 жыл бұрын
Hello again ;) So I understand that the new 2.0.x firmware has tons of stuff for people using a BLTouch or some other sort of ABL system. I do not have any sort of ABL system, and so I need another option. What I had used in the old firmware is the menu under Control -> Motion -> Z Offset that allows you to set your Z offset manually using the dial. I cannot find an option for this in bugfix 2.0.x. How do I re-enable/re-create this menu system and function? Do you have a video on that which I might have missed? So far I have not found an answer to this on KZfaq or Google, likely because the syntax for this menu is highly specific, and when you search for something like "Marlin" "2.0.x" "Z Offset Menu" -"bltouch", you get all sorts of weird things and it is even worse on KZfaq. Help?
@3DPrintscape3 жыл бұрын
Hi. I have never used the z-offset without an ABL system. It automatically gets enabled when you enable the bltouch in the firmware. If your looking to dial things in, you my be able to use babystepping once the print starts but i haven't tried that without the bltouch either.
@kimpanattoni3 жыл бұрын
@@3DPrintscape I am likely to just set it in the slicer. The thing is, back in firmware... crud, I think it was 1.9.something, there was a menu option for setting the Z Offset and storing it as part of the configuration. What I am looking for is a way to bring this back in 2.0.x. Setting it in the slicer is good and all for what it is, but I would prefer it be in the firmware, since it does not need to rely on my software should anything happen to its profiles or my backups thereof. Any ideas?
@thomasbalotte73932 жыл бұрын
My printer is not saving the probe offset. I run through the whole probe offset wizard just like you did, save to eeprom, and the nozzle still defaults to about 3mm off the bed when I go to print something.
@3DPrintscape2 жыл бұрын
Hi. Im wondering if something is up with the eeprm. Can you put an SD card in the printer and save the config again?
@thomasbalotte73932 жыл бұрын
@@3DPrintscape I got it to save eventually, it might’ve had something to do with the z limit switch still being plugged in. As soon as I unplugged it things started working well.
@3DPrintscape2 жыл бұрын
@@thomasbalotte7393 What firmware are you using? The z stop shouldnt need to be disconnected and will cause issues if it is with most firmware.
@corysmith44663 жыл бұрын
Hey Robert, awesome videos, you've helped me learn and understand a lot already so thank you. I seem a bit stuck and was wondering if you had any advice to set me on the right path. I'm currently using an Ender 3 Pro with a 4.2.2 board and a bl touch. The Firmware loaded is from Creality's site and the folder from that zip that contains the firmware is the "Marlin 2.0.1 BLtouch v1.3.1 with transfer board (Temporary)" folder. Everything works fine and I have had some successful prints with it, but I wanted to use the offset wizard. I followed your steps a few times over in setting up my own Marlin firmware and now the BL Touch probe wont deploy when auto homing and it crashes into the board. Any advice you might have would be appreciated and again thank you for all this information you provide.
@corysmith32753 жыл бұрын
Nvm, after reading what I wrote I now understand what the transfer board is and went back to your BLtouch install vid and rewired my setup. Works great now and thanks again for all of this info!
@3DPrintscape3 жыл бұрын
Hi. Im glad you were able to figure it out. The transfer board isnt needed with the Creality 32 bit boards and tends to only cause problems when used.
@zachlittle17872 жыл бұрын
I know this is a year old but i suffer with my dyslexia and add which means i get so far with firmware and loose focus i was ready to 'compile' as people say but i have no tick or option to do so .is there a pre made file already done so i can put on sd for my bl touch skr min v2 e3
@3DPrintscape2 жыл бұрын
Hi. Assuming you have the newer 32 bit board, not the 8 bit one shown in this video. I have firmware that you can use here. 3dprintscape.com/marlin-firmware-builds/
@docotis4206663 жыл бұрын
is this firmware available to download on your website already configured for an ender 3 with the skr mini e3 2.0?
@3DPrintscape3 жыл бұрын
Hi. I did start creating firmware bundles and have one for the ender 3 with skr min. You can download it from here. 3dprintscape.com/marlin-firmware-builds/
@docotis4206663 жыл бұрын
@@3DPrintscape i see the one for the 3 pro with the skr mini. i have a standard 3 with the skr mini will the pro firmware work on it?
@3DPrintscape3 жыл бұрын
Sorry, I thought you had the pro, but the one for the pro should work fine. The big differences between the 3 and 3 pro are the power supply and frame.
@docotis4206663 жыл бұрын
@@3DPrintscape ok. I’ll give it a try when I get home from dinner. I tried building my own and it kept failing when I compiled it in vs
@shootermcgavin38583 жыл бұрын
How do I get this Wizard? Just installed a SKR Mini E3 V2 and a BL Touch... Have the BL Z-stop firmware Marlin 2.0.7.2 installed and it functions properly but the wizard is not shown in the Advanced Settings. How do I get that feature??
@3DPrintscape3 жыл бұрын
Hi. You need to uncomment #define PROBE_OFFSET_WIZARD in the configuration_adv.h file, then build the firmware again.
@shootermcgavin38583 жыл бұрын
@@3DPrintscape My problem was I was trying to use the Marlin auto compliler, it didn't work at all. When I just click the checkmark in the bottom left of VCS it complied properly. Custom screens, all features and modifications are working great!! Someone needs to kick the Marlin auto compiler in the ass because it doesn't work!!
@3DPrintscape3 жыл бұрын
@@shootermcgavin3858 Thanks for sharing this. I had an issue with the auto compiler a while back and stopped using it, which is why i don't talk about it in my videos.
@jeffnelson52302 жыл бұрын
Morning Rob, thanks for the detailed information, just started in this hobby and your videos and website have been incredibly helpful. I have am Ender 3 Pro, CR Touch installed with the Marlin firmware with Z-Homing. Everything seems to work up until the print should start. I send a file to test (I've tried several) and after hearing up the bed and extruder to temp it puts out about half an inch of filament and then stops and starts to cool down. Any ideas? Thanks again, Jeff
@3DPrintscape2 жыл бұрын
Hi. How is the cr touch wired, where did you get the firmware, and was it prebuilt or did you make it?
@jeffnelson52302 жыл бұрын
It's wired from the board (4.2.2 512k) with the standard 5 wire connector. The firmware is the basic bug fix 2.0 from printscape, no modifications. I tried both versions for BL Touch and both give the same results. Jeff
@jeffnelson52302 жыл бұрын
I think I figured it out, after reading your site I was using the wrong file. Thanks again for all of the good information. Jeff
@3DPrintscape2 жыл бұрын
@@jeffnelson5230 Sorry for the delayed response, i was out of town. Is everything working now?
@Patrix4u2 жыл бұрын
Movie great and helpful, but you did not explain what the H OFFSET is used and how to use it in the TFT 35 menu. This appears in version 0.27
@3DPrintscape2 жыл бұрын
Hi. I havent updated to v 0.26 or higher yet. I know they removed the z offset and added in p and h offsets. i believe the p offset is the probe offset and h is home offset but i cant confirm. I will update my tft and make another video on it.
@benrojas54448 ай бұрын
Is this available for ender 5
@3DPrintscape8 ай бұрын
Hi. Its available in the firmware (assuming you have a 32 bit board), i havent used it though.
@jimjones84283 жыл бұрын
when I go into the Z Offset Wizard, it says XYZ Homing and moves the probe to the center of the bed and then it just sits there with the BLTouch flashing and the display says XYZ Homing but nothing else happens and I cant get out of that display message unless I power down the machine and start it up again. But then the same thing happens all over again when I try to use the Z Offset wizard. Thoughts???
@3DPrintscape3 жыл бұрын
Hi. I think this could be related to the firmware and wiring not being in sync. How did you wire the bltouch?
@jimjones84283 жыл бұрын
@@3DPrintscape I wired with the 3p plug going to the BLTouch port and the black & white wires to the Z-Limit switch port. I'm thinking since I'm experiencing a problem, I may just redo it and put the Z-Limit switch wire back in and the black & white BLTouch wires to the BLTouch port.
@3DPrintscape3 жыл бұрын
@@jimjones8428 What firmware are you using? There are two ways to wire the bltouch. You wired it the way I have main wired on my SKR, which also matches the standard config in Marlin. If you are going with the precompiled firmware, you need to have the z-stop connected and the 5 wires from the bltouch connected to the bltouch port.
@jimjones84283 жыл бұрын
@@3DPrintscape I used the version of Marlin Bugfix 2.0.x that you said to download in the video for installing the BLTouch. Then I used the config h and config h.adv from the Marlin website that said it's version 2.0.7.2 which you used in that video to compiled the new firmware.
@jimjones84283 жыл бұрын
@@3DPrintscape Hmmm...As I am rewatching that part of the install video, I believe I downloaded a different configuration file that you did.
@robhopper57292 жыл бұрын
I followed this to the "T" and so my offset is -3.80. When I auto home after this it sets my Z to 13.8.. no where near the print bed.
@3DPrintscape2 жыл бұрын
Hi. The z offset won’t change the autohome location and doesn’t come into play until a print starts.
@mattlogue13003 жыл бұрын
Thx I followed this and got it working. Almost. For some reason it only probes 150mm over and 130mm back. The bed size, min max, and probing margin have been played with, but I'm confused. With a ender 3 with glass and binder clips, whould should be bed size, x y min max.?
@3DPrintscape3 жыл бұрын
Hi. I have my build plate set to 235x235. You can adjust the placements by changing these values. #define X_MIN_POS 0 --- setting to -5 would move the nozzle right 5 mm #define Y_MIN_POS 0 --- setting to -5 would move the nozzle back 5 mm
@mattlogue13003 жыл бұрын
It was the max throwing me off. I didn't get what was inclusive of what. Complies now. I use xmaxpos xbedsize + xminpos. I hope these macros can do math. My cpp is rusty
@mattlogue13003 жыл бұрын
Well shit my rpi died
@3DPrintscape3 жыл бұрын
@@mattlogue1300 If you need help building the firmware you should join the discord server discord.gg/Bu94EYVkrU .
@mikedavis33988 ай бұрын
Where is the link for baby steps
@3DPrintscape7 ай бұрын
Hi. What do you mean, are you saying its not in the firmware or on the screen? Did you clear eeprom?
@mikedavis33987 ай бұрын
I was talking about link to download the firmware
@3DPrintscape7 ай бұрын
I have builds you can download here 3dprintscape.com/marlin-firmware-builds/ @@mikedavis3398
@jonathancanar89562 жыл бұрын
Great video, just one question, I got the skr2 and did the procedure to get the z offset number, I stored in eeprom but should I have to do the fw modification too ??
@3DPrintscape2 жыл бұрын
Hi. Assuming the firmware already has the bltouch enabled. All you need to do is set the z offset at the printer. You could go back and set it in the firmware as well, but then you will need to redo it at the printer if it changes at all.
@jonathancanar89562 жыл бұрын
@@3DPrintscape thanks the answer, any idea why my printer after restarted with the correct z offset, it prints or too high or too close to the bed, I’m using an original bltouch 3.1, and it happen after the g29 ends, I’m confused, almost every time I have to move the offset with baby steps to get a good first layer
@3DPrintscape2 жыл бұрын
@@jonathancanar8956 Did you readjust the z offset with the value change from the baby stepping and save it?
@jonathancanar89562 жыл бұрын
@@3DPrintscape yes after the print start I set the correct height with baby steps and save it to the eeprom, the printer restarts with that value but the nozzle it’s not where it should be
@3DPrintscape2 жыл бұрын
@@jonathancanar8956 You need to take the adjustments made from the baby step process and modify the z offset. The baby step wont adjust it.
@mattlogue13003 жыл бұрын
Mine has control, not configuration. I am pretty sure babystep isn't under tune.
@3DPrintscape3 жыл бұрын
Hi. If you have the firmware updated and dont see babystepping under tune, try to clear the eeprom by going to restore settings in the menu. I also finished up the written article for this video and linked to it in the description, but here is the link 3dprintscape.com/bigtreetech-touchscreen-z-offset-wizard-complete-guide/ . I show the menus in there as well.
@bradonvelueta71172 жыл бұрын
Hey! I was hoping for your help. Ender 3 pro w/ skr mini v2. Followed all your steps in installing bltouch (putting on the 512K text in the platformio file actually caused my compilation issues, so I used what was in the description w/o the 512K). I go to select "Z Probe Wizard and it stops as it homes, and the screen doesn't change from saying "Homing XYZ," Any help?
@3DPrintscape2 жыл бұрын
Hi. They removed the 512k part last year, so what you did was correct. Does everything work if you do an autohome or run a mesh?
@bradonvelueta71172 жыл бұрын
@@3DPrintscape No, the auto home does the same thing. Homes x and y, like moves the bed all the way to the back and the nozzle all the way to the left. But then the bed comes forward maybe 3 in. And the nozzle comes over 5 in to the right and then it just stops, and the screen doesn't change from saying homing XYZ. And I don't know what a mesh is . . .
@3DPrintscape2 жыл бұрын
@@bradonvelueta7117 Is your z stop connected?
@bradonvelueta71172 жыл бұрын
@@3DPrintscape z stop is connected yes
@3DPrintscape2 жыл бұрын
@@bradonvelueta7117 Try to clear eeprom. If that doesnt work, try to push the firmware to the printer again.
@Sendeyap_Ar-Ge3 жыл бұрын
Çok güzel. Başarılar dilerim.
@3DPrintscape3 жыл бұрын
Thanks!
@tobiasdeas68772 жыл бұрын
Hey rob, I use the offset wizard and when I get it at the correct value, I press done and store settings. Whenever i start a print, it completely ignores the settings and buries itself into the bed
@3DPrintscape2 жыл бұрын
Hi. Try to clear the eeprom, then run through the process again.
@tobiasdeas68772 жыл бұрын
I tried everything I could but now I’m just waiting for the 4.2.7 board to show up, because I had the gd chip in the 4.2.2
@tobiasdeas68772 жыл бұрын
@@3DPrintscape hey so installed the new board still having the same problem
@tobiasdeas68772 жыл бұрын
My auto home just makes my nozzle crash into the bed no matter what z probe offset I have
@3DPrintscape2 жыл бұрын
@@tobiasdeas6877 The 4.2.7 board is a nice upgrade, so i think you will be happy with it. The silent drivers make all the difference.
@jimjones84283 жыл бұрын
Ok...so I redid everything again and I am closer...now when I go into Z Offset Wizard, it homes to the front left corner, then travels to the center of the bed, deploys the BLTouch and lowers itself to the bed however, When the BLTouch probe contacts the bed, it doesn't stop. It continues on down until the nozzle contacts the bed and at that point, the Z Axis motor starts making a helluva racket because it has travelled downward as far as it can go. The only way to stop it is to turn the printer off. I did not/do not have the firmware configured to use the Z Limit Switch nor do I have it wired as such.
@3DPrintscape3 жыл бұрын
Hi. It sounds like the firmware and bltouch wiring don’t align. If your using the prebuilt firmware you need to have the z-stop and all 5 bltouch wires connected. If you built the firmware you need to wire the bltouch based on what’s configured. By default, it’s set to work with the bltouch stop connected to the z stop and the z-stop not connected.
@jimjones84283 жыл бұрын
I'm NOT using the preconfigured BIGTREE firmware. I have the BLTouch two pin connector (black & white wires) plugged into the two pin connector on the SKR board that would normally have the Z Stop limit switch plugged into it
@3DPrintscape3 жыл бұрын
@@jimjones8428 Got it, how do you have #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN and #define USE_PROBE_FOR_Z_HOMING defined in the config?
@jimjones84283 жыл бұрын
@@3DPrintscape Directly from the configuration.h file that I used to compile the firmware build....... #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN // Force the use of the probe for Z-axis homing //#define USE_PROBE_FOR_Z_HOMING /** * Z_MIN_PROBE_PIN * * Define this pin if the probe is not connected to Z_MIN_PIN. * If not defined the default pin for the selected MOTHERBOARD * will be used. Most of the time the default is what you want. * * - The simplest option is to use a free endstop connector. * - Use 5V for powered (usually inductive) sensors. * * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: * - For simple switches connect... * - normally-closed switches to GND and D32. * - normally-open switches to 5V and D32. */ //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default .......Also, from what I read in the configuration.adv.h file, I don't believe my application to be uncommon but, incase I am incorrect in my interpretation...with the nozzle just touching the bed and the BLTouch probe is FULLY RETRACTED into the sensor, the distance from the tip of the BLTouch housing to the bed is 4.5mm.
@jimjones84283 жыл бұрын
ok. For anyone following this thread, I have solved my problem. While I did not think it would, I have determined that it DOES MATTER which pin on the Z-Stop connector, on the motherboard, you connect the black and the white wires from the BLTouch sensor. For reference...on an Ender 3 Pro, with the SKR Mini E3 V2.0 , the black wire has to go to the pin next to the Y-Stop connector i.e. the rearward pin farthest away from the BLTouch and flat ribbon display connectors on the motherboard. I also have to assume that when using the 5 pin BLTouch port for this connection, it WILL matter which pin gets which color wire. Good luck and Thank You SO MUCH! @3D Printscape for all you attention and help in this issue! It is GREATLY appreciated!!! And keep up the great work with your tutorial videos!!!
@wernerdriehorst64593 жыл бұрын
Hello 3D Printscape, excellent videos !!!!!! Very well explained and at a reasonable pace !!!! That I, too, can come with my little English !!!!!! Their website is also very, very well structured and all topics are explained very well !!!! I have a question and a request for you at the same time! I also want to use Neopixels on my Ender 3 Pro! Would it be possible that you can send me a BIN file, where this function is already set correctly ?! Until now I have installed the firmware Marlin 2.0.8.2 on my SKR Mini E3 v2.0 with BLTouch and direct drive extruder! I don't dare to use this programming of the neopixel settings !!! That's a little more complicated !! You shouldn't create this for otherwise !!! Please tell me your effort and the appropriate payment !!!!! Many greetings from Germany: Werner
@3DPrintscape3 жыл бұрын
Hi. I believe you reached out on discord, if that wasnt you, please let me know.
@michaelweiss80899 ай бұрын
can i get the link to your previous video
@3DPrintscape9 ай бұрын
Hi. Which video are you looking for? If you go to the channel you should be able to search for it but if you give me the name i can try to find the link for you.
@michaelweiss80899 ай бұрын
LOOKING FOR SETTING Z OFFSET FOR CR TOUCH. @@3DPrintscape
@gonzabaldo3 жыл бұрын
Can I use this? I'm using UBL with a capacitive sensor, successfully. But this will be a real time saver.
@3DPrintscape3 жыл бұрын
Hi. I havent actually tested that but i think it will work.
@gonzabaldo3 жыл бұрын
@@3DPrintscape I'll test it and come back with the results. Great content!
@3DPrintscape3 жыл бұрын
@@gonzabaldo Sounds good, thanks.
@gonzabaldo3 жыл бұрын
@@3DPrintscape Working great with ubl too. Thanks!
@xALFx133 жыл бұрын
How do you get it to save i do not have that feature on my when i do a ABL run
@3DPrintscape3 жыл бұрын
Hi. If your running with the standard scree, you would go to store settings. You should find it here Menu - Control - Bed Leveling - Store Setting .
@xALFx133 жыл бұрын
@@3DPrintscape got it thanks
@CelticNickC7 ай бұрын
Used your bug fix-2.1x firmware for ender 3 sir mini e3 v3.0 files for config. Trying to follow this video, but z is still running into the build plate. W glass bed. Unsure of what I’m doing wrong here
@3DPrintscape7 ай бұрын
Hi. Do you have a bltouch or crtouch installed and is the z stop connected?
@CelticNickC6 ай бұрын
@@3DPrintscape crtouch connected with z stop as well. Have not gone through coding yet, as I’m trying to learn and understand how the printer works with these upgrades via these videos/trial and error Printer: ender 3 from original 8 bit model Upgraded to skr mini e3 v3.0 W/tft35 e3 v3.0.1 touch screen Tmc2209 upgraded 32bit silent main board W/ crtouch with description reading [for 32bit v4.2.2/(.7) mainboard]. (-->I’m unaware if specific firmware would affect the crtouch performance in this manner or if that description matters)
@3DPrintscape6 ай бұрын
@@CelticNickC When you said you havent gone through the coding yet does that mean your running the stock skr firmware? If so, the crtouch wont work but the z stop should still stop the z axis, assuming it was triggered.
@CelticNickC6 ай бұрын
@@3DPrintscape I flashed it with the bug fix-2.1x firmware on your page for ender 3. I haven’t figured out how to get it to stop from crashing into the bed yet. I have a glass bed as well, so it may likely be higher than average. I believe you also talked about that in one of your videos. Trying to go back through each of them to solve in parts where I have time to. I appreciate you making replies!
@3DPrintscape6 ай бұрын
@@CelticNickC Did you use the bltouch build from my site? If not, that is the one you need. The glass shouldnt make a difference for the bltouch but if it prevents the endstop from being engaged it will cause issues.
@jacquesdupuis80783 жыл бұрын
thank you I made the changes in Marlin-bugfix-2.0.x via visual studio code compile and installed via SD card on my ender 3 pro with the above mention board. But idon't get the menu probe Z offset wizard. How is your BL-Touch connected to the V4.2.7 32 Bit Board? Black and white wire are in Z-End stop
@3DPrintscape3 жыл бұрын
Hi. I have the 4.2.2 board but I have tested this on the 4.2.7 one as well. I have both the z-stop and prob stop plugged in. Try to clear your eeprom and restart your printer. Also, you can you the discord server if you are still having issues. discord.gg/Bu94EYVkrU
@jacquesdupuis80783 жыл бұрын
@@3DPrintscape How can I clear the eeprom I restore to default and flash the firmware but I cannot see the wizard should I reinstall the Z-Endstop and wire the BL-Touch to the other place?
@3DPrintscape3 жыл бұрын
@@jacquesdupuis8078 Are you able to join our discord server? I think this will be easier to troubleshoot there. discord.gg/Bu94EYVkrU If not, can you email me your config files and an image of your about screen and any other menus that make sense. My email is admin@3dprintscape.com .
@jacquesdupuis80783 жыл бұрын
@@3DPrintscape i Follow your Video about marlin Firmware starting from a virgin version downloaded like you explained and it works I see the wizard and a lot of feature that I never seen bevor Thank you a lot for your assistance
@3DPrintscape3 жыл бұрын
@@jacquesdupuis8078 You're Welcome!
@mikaelcarlborg64373 жыл бұрын
Still prints in air after this wizard. Missing 2-3mm from the nozzle to the bed. Tried everything.
@3DPrintscape3 жыл бұрын
Hi. If its still printing in mid air, the z offset is not correct or you have a lot of movement in one of your axis's. I would go through and make sure everything is tight.
@mikaelcarlborg64373 жыл бұрын
@@3DPrintscape Still haven't found the problem...i solved it by adding an extra 1.8mm to z offset. That makes it work for now. Thanks
@MobileDecay2 жыл бұрын
The wizard never sets the value when I save it.
@3DPrintscape2 жыл бұрын
Hi. The value should get saved but doesn’t actually do anything until a print starts, an autohome doesn’t use this value. Also, make sure to save your settings before turning the printer off.
@MobileDecay2 жыл бұрын
@@3DPrintscape Yeah even when I start a print it doesn't take the value. I did save it. ☹
@MobileDecay2 жыл бұрын
@@3DPrintscape Okay upgrading to the latest bugfix seems to have fixed the issue. 😊
@guenzburghdcl76373 жыл бұрын
Cool, but the tft35 screen has changed and functionality is different, also difficult to understand without telling people about platformio and marlin auto build software first , anyway thanks
@3DPrintscape3 жыл бұрын
Hi. Thanks for the feedback. The TFT firmware was the latest at the time I made the video, I will check out the newer releases. There are links to videos on how to build the firmware in the videos description, I figured that would give the viewers what they needed
@y0k0z00na2 жыл бұрын
What does this mean??? Build Firmware VS Code user interface. That will kick off the build and shouldn’t take longer than a couple of minutes to complete. You should see success in the terminal window if everything worked. If it didn’t, you will be able to get the error from there to troubleshoot. VS Code user interface, huh? Not a complete sentence so not sure what you mean.
@3DPrintscape2 жыл бұрын
Hi. Sorry im in the technology field so many times i talk as such. VS code is the software, user interface is just the application interface. Not sure if that helps much.
@chrisb3989 Жыл бұрын
Another guy who wants to set the z offset one random piece of paper too high…..why? The firmware expects z zero to be the bed level not the bed level plus a random bit of paper. Bring the nozzle down to a known feeler gauge then drop the z offset by the value of the feeler gauge. Never have I seen an engineer or cnc machine operator using bits of paper….
@3DPrintscape Жыл бұрын
Hi. You dont want the z offset to be at exactly 0. Doing this will have the nozzle too close to the bed when it prints and will cause other issues including filament jams. Using a precise 1mm feeder gauge would work better than a sheet of paper but most people dont have anything like that laying around.
@chrisb3989 Жыл бұрын
@@3DPrintscape so you think the clearance on the bed for printing set by the firmware is too close? I suppose you could edit and recompile the firmware I think the firmware I run prints .2mm above the bed if I add a bit of paper to the z offset that it will likely be actually printing at .3mm …who knows for sure it would depend on which bit of paper I have lying around……anyway I suppose it’s whatever makes your prints come out how you want them.
@jondoough8 ай бұрын
This is terrible. Same with your website. None of your instructions actually work.
@3DPrintscape8 ай бұрын
Hi. Sorry to hear that. I have helped many of people but I’m always open to improving things. What issues are you having?
@marcelrios806 Жыл бұрын
I have a problem "Marlin/src/lcd/menu/menu_probe_offset.cpp:124:20: error: 'PROBE_OFFSET_START' was not declared in this scope probe.offset.z = PROBE_OFFSET_START;"
@3DPrintscape Жыл бұрын
Hi. What config example are you using and does it build fresh (so just using the example with no changes)?
@marcelrios806 Жыл бұрын
@@3DPrintscape I'm setting up an Ender 3 pro with bltouch.
@3DPrintscape Жыл бұрын
@@marcelrios806 Gotcha, but what marlin config example are you starting with and if you build it before making changes does it work?
@marcelrios806 Жыл бұрын
@@3DPrintscape I'm using the examples provided by Marlon in his latest version 2.1.2
@3DPrintscape Жыл бұрын
@@marcelrios806 Ok, but which one specifically? Under config examples there are the different brands, printer models, then boards. Im trying to see if its an issue with the config example or possibly something in VS code on your side.