Well breaking in. Is just for racers if your just chilling you don't need a broken in motor. As in just for fun but you cam still do it if you like. As for me I'm fine nit breaking in until I get more track pieces or a bigger track to race at In general

They're not meant to race against Fully Modified setups, so they will definitely lose. These are designed for Tuned Class, which entails no Cutting and Tuned Motors Only. But I will do a video of a race-off of MA vs AR vs FM-A.

Trigale Black Special or Aero Avante Black Special.

Z3N Bluster thank you so much!

You can slow down the video by choosing to watch at half or quarter speed. It's mounted with its normal ball shaped screws.

@@Z3NBluster Thank you so much! I already ordered those in my local hobby shop. More power and thanks again! Im currently building a Rowdy Bull from the starter kit :D

I didn't replace them with FRP. Those are carbon fiber. They are stiffer and allow for faster weight transfer during cornering. And no, they don't weigh the same. You just need a more accurate scale to tell the difference.

Look for the video "FM-A Chassis Basic Build Part 1" on my channel. The parts are listed there.

Look for my videos comparing this car to my MA and AR Basic Builds. I discuss some changes I made there and you can see how this compares to my MA and AR builds on the track.

The double aluminum roller with o-ring bites harder when it goes through the three-lane lanechange. It also helps slightly offset the balance of FM. FM is slightly heavier on its left side. Putting that on the right nudges the center of mass closer to neutral.

Z3N Bluster thanks for the info. Will that kind of setup suit an super2 with a bumperless and long tail set up?

It can, you'll have to make adjustments to get the dimensions correct due to the difference in roller positions compared to using 19mm rollers in the front.

@@Z3NBluster ok noted thank you again! Looking forward to your future builds.

Watch my MA Chassis Basic Build videos part 1 and 2. In my Tamiya Mini 4WD Build Playlist in my channel. Your Avante Red should fit in an MA chassis.

Sometimes it cost 1500 or even 2000 bro

I said it in part 1 it's designed for Tuned Motors. To accommodate Power Dash you will need to also have front brakes.

OnigiriInfusion It's not designed for the Brocken G.

I think you can change the front stay to 94950.It works on my Strato Vector cowl

Nope, the Super FM Front Bumper requires heavy modification to fit the front bumper set in this video. The Super FM Chassis does not have side mounts to accomodate the side dampers in this video. The Super FM Chassis does not have a two point attachment in the rear to accomodate the rear bumper setup on this car.

Z3N Bluster Hi Zen, thank you for your quick respond. I have one more question for you. I was brwosing DXN web site to purchase all the parts I need. What did you do when they don't have certain parts? Do they order for you? and is it free to use track on shop? I live in San Diego and planning to visit one day. Please advise.

When I bought my parts at the time of this build it was complete. Whatever part is missing you'll have to find something comparable and use that instead. If you by a certain amount of parts that qualifies to run your cars on the track. The DXNProvisions page has contact information. Send Scott and email and he will reply to your questions.

If you use 3mm for the front underguard mount, you risk having the front too low and it might not pass the 1mm clearance rule. If you're going to use it as a roller mount for the front, that's probably doable. If you can not find the HG carbon 1.5mm parts, just use the FRP version of the same shape.

Z3N Bluster Can I use the frp that comes in with a Rowdy Bull starter pack sir?

If it fits? Yes.

Spoilers are just style. It is uncertain whether or not they help in Mini 4WD.

@@Z3NBluster well thnks for answering my question zen..by the way im from the philippines..kababayan hehe😎 keep it up pre..maganda ung mga contents mo marami kang na tutulongan na newbie tulad ko..

You might have bad bearings on your rollers. Buy some replacement AO 520

and another thing, i noticed that the rear damper/hammer damper at the back always came off during jumps..at first run i doesn't but eventually as it always came off especially during jumps..what do you think the alternatives so that it will not came off? TIA

I did not create a list. Watch part 1, I physically showed each part needed in the first 2-3 minutes of the video.

Look for a playlist in my channel called, "Tamiya Mini 4WD Build." In there there's a full guide on how to build FMS2.

ChrissyNick To make the car lighter.

Z3N Bluster thnks for the info mate..bt i really like spoilers on xto to add more beauty...nice build though i definitely follow ur set up and of course with the spoilers..thank you hehe

Gertie Ryan Sancha Puwede. The Double Aluminum Roller on the right - front side is mostly for the lanechange.

The double roller is for the lanechange. It bites a little harder on the lanechange if you need it to.

Nico Limchoc Monday night US time there will be a race comparison video between this, the AR build, and the MA build.

+Drew Fox I'm reversing the polarity. You're reversing the polarity back!

Brabus 1Up I'm guessing you're referring to the rollers? For the lanechange.

No.

@@Z3NBluster ok sir, thanks!

On KZfaq, you can slow down the video by selecting half or quarter speed playback. That should allow you to slow down the footage enough to see what's going on.

@@Z3NBluster thank bro.. It helps a lot...

Watch Part 1. All the parts are listed there.

@@Z3NBluster do you have build for NIGHT HUNTER, Speedtech

I don't understand what you just said.

Why fama chassis noisy whereas full bearing