No video

Zenith 5R086 - Episode 12 - Idler Wheel Refurb and Assembly

  Рет қаралды 6,919

Fibber's Closet

Fibber's Closet

Күн бұрын

"Restoring" the idler wheel, synchronizing the turntable

Пікірлер: 18
@jas20per
@jas20per 10 ай бұрын
Wintergreen to soften rubber is not new idea, was doing this twenty five years ago. It works much better lasts far longer if you just massage wintergreen into the rubber after softening it first in just more than the hand can stand hot water.
@mikedomachowske2364
@mikedomachowske2364 3 жыл бұрын
Thank you so much for all this great info!
@fibberscloset498
@fibberscloset498 3 жыл бұрын
Thanks for watching, Mike.
@zorkikat
@zorkikat 3 жыл бұрын
Hi, a couple of months ago, I tried the alcohol+wintergreen treatment to various hardened rubber objects which included four turntable idler wheels ( 2 from a 1970s BSR, a 1960s Dual, and, a 1970 Matsushita), rubber gasket mounts for a BSR motor, and a 30 year old rubber/vinyl camera strap. The soaking times varied from three to five days. The treatment was tested first on a damaged BSR wheel which was soaked for 5 days. It softened after about a day and a half, but I decided to leave it in the solution for 5 days, following the instructions found in other sites. When I took the wheel out after 5 days, it crumbled. The soaking times were shortened to 2-3 days. Indeed, the rubber objects came out soft and supple, and smelling good from the wintergreen. The Dual relied on a very pliable wheel to make the platter spin. The softened idler wheel did make the platter turn, but only for a couple of days. All the parts lost their suppleness in about 3 days, and a week after, all were back to their old hardened states. The old camera strap, though, is an exception: it took slower to stiffen up again. While it is still pliant today, it is no longer as soft as it was when it emerged from the alcohol+wintergreen solution, when it rolled nicely like fabric. Now it is about as stiff as thin card. :)
@fibberscloset498
@fibberscloset498 3 жыл бұрын
Interesting. Thanks for sharing your results. One of these days I'll dig out the turntable I did the treatment on and see how it's held up over time. Given what you have found, I expect to see either a pile of rubber or an idler wheel that needs replaced.
@trondam
@trondam 3 жыл бұрын
Hello, love your video 😊 Try and sand down the idler wheel so it's even. The rumble may then go away. The rubber was a bit uneven on the top.
@fibberscloset498
@fibberscloset498 3 жыл бұрын
Thanks for the tip!
@jefferylarson3218
@jefferylarson3218 3 жыл бұрын
Just from my own experience. I do a lot of audio stuff, and this issue comes up in old reel 2 reel decks. I tried the alcohol wintergreen thing. And while it did soften the rubber, after a few days in the open air, it turned hard again. As for lumpy/rumbly sound, I mount idlers on my drill and use 150 grit hard paper to round the corners down. Also pack the spindle (bearing) with good quality heavy weight moly. But after this vid, I am thinking I need to look back, and maybe try this method one more time. About a month later and I'm going to try this again on an old BSR idler. I'll let you know how it goes. BSR idler about 40mm diameter. After 24 hours it disintagrated. Oops.
@fibberscloset498
@fibberscloset498 3 жыл бұрын
I look forward to hearing about your results.
@shopwornbear1171
@shopwornbear1171 2 жыл бұрын
I'm not sure if you read backwards with comments, but this just popped up on my feed. I have no idea if this could actually work, but if it does, it's a brilliant (and very inexpensive) solution to rock hard idler wheels (depending on whether or not the configuration is compatible). Have a look if you wish: kzfaq.info/get/bejne/fJajmrKg2NfKaGg.html
@fibberscloset498
@fibberscloset498 2 жыл бұрын
Hey, Bear, thanks for the lead. Looks like a technique I'll have to try out.
@premverma61
@premverma61 3 жыл бұрын
How to get spares, idler wheel,I need 1.Pl. help me in getting that.for my HMV turntable.
@fibberscloset498
@fibberscloset498 3 жыл бұрын
Hello, Prem, idler wheels for a lot of turntables are available from thevoiceofmusic.com.
@marty-fh1rw
@marty-fh1rw Жыл бұрын
I sent an idler wheel for an (then) unknown brand turntable to Russell Industries in NY for rebuilding.They are nice people.A KZfaq man kindly put me onto them.
@jefferylarson3218
@jefferylarson3218 3 жыл бұрын
Did it STAY soft?
@fibberscloset498
@fibberscloset498 3 жыл бұрын
I just took it down off the shelf for the first time, and yes, the roller is still pliable.
Zenith 5R086 - Episode 13 - Turntable cleaning, Reassembly and Test
10:13
Making a Turntable Idler
23:00
Everett's Workshop
Рет қаралды 20 М.
لااا! هذه البرتقالة مزعجة جدًا #قصير
00:15
One More Arabic
Рет қаралды 51 МЛН
Идеально повторил? Хотите вторую часть?
00:13
⚡️КАН АНДРЕЙ⚡️
Рет қаралды 18 МЛН
小丑把天使丢游泳池里#short #angel #clown
00:15
Super Beauty team
Рет қаралды 42 МЛН
Idler Drive Turntables!
11:24
Record-ology
Рет қаралды 8 М.
Part #1: The RCA 45 RPM Idler...REBUILD IT YOURSELF!!
8:59
seeburgsrock
Рет қаралды 28 М.
1967 Magnavox Micromatic Turn Table Maintenance
21:19
shadowrider460
Рет қаралды 57 М.
how to fix an idler wheel in turntable
9:49
Andres Mera
Рет қаралды 31 М.
BSR Idler wheel - making my own
26:33
mrrgstuff
Рет қаралды 12 М.
Recycled idler wheel rubber of LENCO B55 turntable
6:26
Woody's Hobbies
Рет қаралды 8 М.
1950 Recordon renovation part 2 - Turntable drive idler wheel restoration
9:01
Robert Jenkins Technology Channel
Рет қаралды 4,3 М.
Basic Service of early 60s VM record changer Part 1/2
38:12
Jordan Pier
Рет қаралды 41 М.
لااا! هذه البرتقالة مزعجة جدًا #قصير
00:15
One More Arabic
Рет қаралды 51 МЛН