Wait is over guy's...Tool making video kzfaq.info/get/bejne/l9Fmfcuqy8mnpmQ.htmlfeature=shared

Cool video. It's not shown, but he had to align the oil feed hole in the piston pin before pressing it in, and the cam sprocket also had to be aligned (so the timing will be right) before pressing it on. I'm always amazed that these little press together cranks stay true during running, given that such a relatively gentle smack with a hammer is all that it takes to twist it on the pin a little bit when lining it up.

They obviously take their motorcycles much more seriously than their trucks. Decent tools, relatively clean, and even a dial indicator.

Very nice tooling! This is the right tooling for the job! Nice work my friend! 👍

The three eccentric tool is handy, we used to scribe two lines before disassembly.

Finally, a local street bike shop who knows what they're doing!!

Очень достойный результат!

Super robota fantastyczny specjalista

Il était largement temps de changer cette bielle 😱 ça fait mal quand le roulement de tête casse comme cela m'est arrivé avec mon Suzuki Gt Beau boulot même si c'est plus facile qu'avec un multicylindre 😉

muito legal suas ferramentas simples e funcional top das galaxias ........

Jgan guna besi ketuk nya..guna termagar kuper besar ketuk nya agar tidak berkesan..

Good video, very good workmanship, but this has nothing to do with crankshaft balancing, it's crankshaft aligning.

This guy knows his job.

Alat yg bagus untuk hasil yg lebih persisi, great 👍👍👍👍

Good job brother 👌

عمل جيد واراك تحب هذه الاعمال المتعلقة بالدراجات النارية

thank you for sharing your experience

Excelente gracias por compartir muy técnico lo felicito

Well Done!

good work, please make a video reviewing hydraulic tools along with their tools and sizes

Wow what a clever bearing puller😅

Newly connecting rod pin differs from old why? (Stepped pin).

Hey q bárbaro como puedes cuadrar un cigüeñal pegándole golpe esos golpe de figuran el cigüeñal sea más estético

You didn't check side clearance on the rod.

Begitu kah cara mengecek setang pistonya di pukul pukul

Good job

Excellent work

Молодец

Great work. Well done

How to balance twin cylinder crank shaft boxer type design?

How does the crank stay true when running if it only takes a small blow from a hammer to correct its trueness ???

Migunani jig josss

Sou o único brasileiro vendo esse video

Where can I buy this?

А звезду привода цепи распредвала как установить?И как ходят такие коленвалы после ремонта?

Nice

Beautiful work.

Need to make one that is really nice....

well done keep it up.

я понял тепловой зазор между шатуном и щекой не выставляете !

Crankshaft truing

Cũng ok đấy bạn

0.5 lock side and outher side 25 thats all for balance

Great work idol, always supporting.

mantap kang,kpengin punya alat ky gitu😢😢😢

VERY NICE

Lokasi dmna iya bang

Good work

Very nice

there goes another crank... he didn't align the oiliong hols to the port holes int he crank halves. so no oil will get to parts.. yea!!!!

Cool jig, Did you make it by your self??

Do you service bike engine ❓ pls give rply

You didn't balance the crankshaft, just trued it.

pital hathora bnwa lo bhai

Mantab bos cara kerjanya 👍🤲🤲

@Zimbiker where can i find the metal blocks you use to disassemble the crankshaft?

There was no balancing just alignment

The thing the press is pushing down to seperate it what is that called and where do I buy one

Tenho uma ferramenta muito mais simples e eficaz.

ใหญ่วัดบึง

Bermaanfaat👍

total Cost kitna lagega yeski liyr

I want this complete alignment tool

Bhai muje Kam sekna han AP ki shop kaha han

You missed the balancing part

Do you have any videos of how you made the tools?

Anong motor poyan boss

better buy 1 set with crankshaft 😅

Bro Kiya ada bana ya he man gay apki ustadi ko

Address bata do. I like your work.

Price

❤❤❤❤❤

location please

Where is your location?

Where can I buy this tool

Com a biela no pino facilita

4:20 What is the name of this one in your hand?

Never see this tool in my country

Joss

Böyle işçilik olmaz

location

Sir yea toos kider malta ha😊

Bhai aadras bata do koe

ur loction

Hay a

Instagram link instagram.com/zimbiker

Location ng shop sir?

Dukan kha ha apke

Location

Number or location please

👍👍👍🇧🇷🇧🇷🇧🇷🏆🏆🏆

Bonsoir comment allez-vous je voulais demander votre numéro WhatsApp

Good job