Zortrax Inventure Desktop 3D Printer Review - Soluble Supports, HEPA Filter and Assisted Levelling

Рет қаралды 1,040

Күн бұрын

300 hours of printing later, I bring to you the Zortax Inventure Review.
Does it deliver!?
Yes, I think it does. Soluble supports, reliable printing and the added HEPA filter make this a great addition to a home, office or print farm.
Zortrax Inventure Specifications
- Build volume: 135 x 135 x 130 mm (5.3 x 5.3 x 5.1 in)
- Material diameter: 1.75 mm (0.069 in)
- Nozzle diameter: 0.4 mm (0.016 in)
- Dual, printing with model and support material
- Material detection sensor (for filaments in cartridge only)
- HEPA filter
- Connectivity: SD card (included)
- Assisted Levelling: Automatic measurement of platform points’ height
- Enclosed Heated Chamber up to 80˚C
This printer is available directly from the Zortrax store:
store.zortrax.com/
You can also browse their other printers here (If this one is anything to go by, I may be trying more in the future)
zortrax.com/3d-printers/
Thank you for watching, don't forget to like and subscribe =)
If you want to support me and the channel, you can either buy me a coffee or buy some 3DTomorrow Filament if you're here in the UK.
PayPal.me/callumcoles
3DTomorrow.com
00:00 Introduction
00:29 Spec Check
02:22 The Review
03:20 Pro 1 - Dual Extrusion
04:14 Pro 2 - Bed Levelling
04:58 Pro 3 - Bed Durability
05:42 Pro 4 - Reliability
05:57 Pro 5 - HEPA Filter
06:14 Bonus - Scraper
06:28 Pro 6 - It Just Works
07:08 Pro 7 - Build Quality
07:25 Proprietory
08:00 Pro 8 - Material Range
08:31 Con 1 - Material Loading
09:03 Con 2 - Spool Capacity
10:05 Con 3 - Build Plate
10:57 Con 4 - Draft Excluder
11:27 Con 5 - Proprietory
12:29 Recommendation
13:50 Print Example
14:53 DSS Wash Station
15:11 Solution Disposal
16:39 Before Removal
18:07 After Removal
#Zortrax #DualExtrusion #3DPrinterReview

Пікірлер: 8

@yvesloy652 2 жыл бұрын

Thanks a lot! This is exactly the review I needed ☺️

@CallumColes 2 жыл бұрын

You’re welcome, glad it was useful for you:)

@army310 2 жыл бұрын

good review and it looks good but on the high end side

@CallumColes 2 жыл бұрын

Thanks for the comment, much appreciated! Yes it’s certainly a prosumer level printer, but I think anyone with a genuine need for more exotic materials would be very satisfied with this printer.

@Test4697 2 жыл бұрын

Really nice review! Well done. Is it possible to share what needed calibration when you printed the bearing in the pre review video? Thanks again a lot for the honest review.

@CallumColes 2 жыл бұрын

Thank you! Yes of course, so basically the bearing fused together slightly as there was not quite enough tolerance in the model to print with the default settings. So in the Z-Suite slicer, you are able to adjust some settings under the 'OFFSET' menu, 'CONTOUR OFFSET' and 'HOLES'. By tweaking those, I was able to effectively adjust the tolerance in the model so the bearing segments didn't fuse together.

@sungyoon6376 2 жыл бұрын

Thanks for a nice review. Have you experienced ‘build tray not seated properly’ error at the beginning of printing? It keeps happening to me. Usually Works after resuming (and rechecking the tray), but quite annoying.

@CallumColes 2 жыл бұрын

You're welcome, thank you for the comment! I haven't had that error no, but then again, I've never removed the build tray since I've had it... Have you tried contacting Zortrax support? Perhaps they can shed some more light. If all else fails, could always try a different built plate in case something is misaligned with your current one.