@@erichook1519 Thanks ! I wouldn't chance putting the gas in anything else. I believe the filter housing has 3 screws.2 nuts that hold the carburetor. And one on the back side.

Got my generator back up and running…have a small problem though…see picture-do you know if I can buy this part by itself? Do you recommend just replacing the rubber gasket?

Having issues uploading a photo…it’s the larger screw that secures the bottom cup of the carburetor to the top. The larger rubber gasket to the inside of the carb (when screwed in) is frayed-can you buy this part by itself?

What is the fuel line size?

Thanks so much glad it helped!

🤣🤣🤣glad I could entertain ya. Hope the video helped in some way. Thanks for watching!🙂👍🏼👍🏼👍🏼

Thank you Kind sir. I appreciate you. Glad the video helped ya.

in the video at 43:04(the firman generator) is the washer your talking about fiber or rubber@@chrisdixon2525

Good observation sir. I realized it when I put the new clamps on. It was right when it left my shop. Easy to do when ya trying to make a video instead of concentrating on the work. 😄👍🏼

For the carb

I don't have parts for sale. Just look up what you need on Amazon or Google it. Thanks for watching.

No worries I have all the gaskets and plastic part of or for the carb Ty for this video

Meant order as in placement

My bad🫤 If ya can't figure it out get back with me. Sorry. Thanks for the sub.😊

Thanks for the info. And thanks for watching

Glad it helped ya out. Thanks for watching

@@chrisdixon2525quick question. My battery took a hit from me trying to start it 30 times without it starting before I cleaned it. If I leave the generator running for a hour or two will it recharge the battery? I have a pull start on it to. But I started it with a portable battery jump. I don’t have a slow charger right now but was wondering if i just left it running will it charge up the battery again. Thanks

It may help a little Probably won't fully recover without charging on battery charger.

Hope it can help in some way! Thanks for watching.

Hope the video helps! Thanks for watching 👍🏼🙂

Around 35$-45$ on Amazon. Just search model# of generator on Amazon.

I did buy it. For $40 delivered I’ll save myself an hour of time. Thanks for the video, I’ll use it on the install and then play with the old one to have as a backup

I did buy it. For $40 delivered I’ll save myself an hour of time. Thanks for the video, I’ll use it on the install and then play with the old one to have as a backup

I don’t know why that posted twice

🤣👍🏼no problem

Thanks for watching and the comment 👍🏼🙂

Look up on Amazon carburetor gasket kit for 439cc clone engine. If yours is exactly like the one in the video. Should have a decal telling engine size. Should get multiple gaskets in one kit for like 10$.

Local parts store have different thickness of material for gaskets and you can make one

Hope ya enjoyed it. Check back often for more. Thanks👍🏼🙂

I just take the fuel line off the carb. And drain old gas out of the tank. I spray carburetor cleaner in the tank and attach an old piece cloth to a wooden stick or dowel rod and wipe the interior of the tank as much as possible. Pour a little gas in and swish it around and drain it. Repeat until tank is free from rust and crud. Install inline fuel filter between tank and carb. Fill with gas and change the fuel filter as needed . Hope this helps. Thanks for watching. Stay tuned for more helpful videos. 🙂👍🏼 If ya need more help, let me know. I'll make a video to help ya.

Thank you. I’m planning on trying to run off propane only so I don’t have to do this as often.

No problem Yes I agree on the propane. I haven't tried mine on propane yet but I'm ready to try it

Went through all the steps and generator still won’t start (propane only). It cranks and just chuggs but doesn’t run. Any tips on what to try next? Spark plug maybe?

@@BT-bx1un so it runs good on propane ?

Thanks for watching . 👍🏼🙂 Yessir some of the saws have some odd problems. I've worked on some that I never got fixed . Pretty sure it's air leaks in the crankcase that don't show up when it's not running. Thanks for watching hope you found some help or entertainment from my channel. 🙂👍🏼

Hope it helped 😊👍🏼

Yes sir, I did it just like the video, thank you very much

You're very welcome. Keep watching 🙂👍🏼

Yes sir.

Question 🙋🏻‍♂️ What kind of oil can I use for this generator?

Lol

The one and only😂😂😂

Glad you enjoyed it. If you have any questions I'll try to help anyway I can Thanks for watching 👍🏼🙂

10-4 Thanks for your input🙂👍🏼. I'm trying to get better at my videos. Stick around . Thanks again!

I guess over time it might. I try not to soak the tip just wipe it off. I've never had a issue with the filters I use.i guess there's potential if the filter was super restrictive. There usually is a small filter in the on off valve but I didn't pull this particular one apart. Fuel free flowed freely when I had it apart. Thanks for watching. I'm not a certified professional mechanic. But I do normally end up with a pretty good repair. I do appreciate your feedback 🙂👍🏼

Awesome hope it helps. I'm not the greatest but if you have questions feel free to hollar back at me🙂👍🏼

🤣🤣🤣yessir, you would think so.but the can is a great cushion. It's really not as loud as you would think.thanks for watching. Hope you were entertained or found something that would help ya out. I'm learning new stuff every day.

Hey @alexsails80 we use Tri-mix gas made for Stainless 90%helium 7.5% argon 2.5% co2. Stainless don't flow as well as carbon usually run a little hotter using basically the same techniques as carbon you just need to put the puddle where you want it because it's not gonna flow as well as carbon. Right Gas will help if you hadn't been using the tri-mix Hope this helps. Thanks for watching!

Hey Daniel the location of the line in the tank really doesn't matter. If you're not sure, the line with the filter is in-flow. If you're still not sure just pump the bulb with both lines attached one will pump out the other will suck in. Just note the suction and install in the tank with filter attached and make sure the filter lays in the bottom of the tank. Hope this helps. If not let me know.

I've posted another video about your question. Check it out and let me know if you need more help. Thanks for watching

Yep y'all got it going on😂

Thanks,Bud🙂👍🏼

🤣🤣👍🏼 You have made my day! Good times

Yessir enjoyed hanging out at school with ya! KEEP ON TRUCKIN' Keep watching ,more videos on the way.

Thanks Mr. Michael I really enjoyed my time with y'all. You sir are a great instructor!!

Thank ya sir!👍 I enjoy making them. Keep watching 🙂

You're the best! Thanks Thomas 😉🤣🤣

Yessir you're right. Thanks for checking out my channel 👍🙂

Hey good job... I'm with you on the poulan .not a bad saw you have to maintain them ...good fuel ..good oil. Keep it clean . Air filter thank you

Yessir it is. Normally they don't have to heat up like this one but this shaft needed a 80% tungsten spray.

Yeah, we'll have to pull them out. This was just a good starting place .

Be neat to see those !

@@kennys9855 thanks Kenny. I hope to pull out our old trucks for a video in the future. Keep watching! Thanks again

Cool! Thanks Bud If you have questions we'll try to help.

Appreciate it. Same here 👍

10-4 I'm sure there's plenty you could help me on. Feel free to input info. 🙂👍

Thank ya! I'll try to do more.