You didn't even show the viewers when you were putting in the cover
@prafsha9789Ай бұрын
Where is this spot?
@nunya51072 ай бұрын
Hey Shawn I lost ur info on Facebook I chatted with u a few years ago but I've had a few family loses and health scares but I'm still interested in ur kitt bumper how do I find u on fb
@itzBiscuitsB3 ай бұрын
what i needed to see was cut out some good info still but still searching
@CodyNelson-nightmoves4 ай бұрын
Wish I would have watched this before before I tried to figure it out on my own as I went along. Now I got Niagara falls in the front of motor. I got two quarts of oil sitting in my cross member
@Baron-Von-19735 ай бұрын
Why the fuck would you even think you need to remove the fucking oil pan??
@AC.Prince7 ай бұрын
Did that fuel pump fit? I've never seen one like that on a sb chevy
@mrsuarez4308 ай бұрын
Why so people say you have pull the oil pan lol I didn't have to even loosen it I have a 305 97
@s1mph0ny7 ай бұрын
Some of the pans and timing covers are shaped different, especially the ones with 2-piece timing covers.
@straighttimestirrups11 ай бұрын
Would’ve be nice to see the cover with the tabs cut-off (before-after) photos and show how you actually installing it.
@harrytaylor6081 Жыл бұрын
Thanks for the advice
@andrewsturgill9893 Жыл бұрын
good stuff
@vezina808 Жыл бұрын
How do you install the timing tab?
@genen.7370 Жыл бұрын
What type of silicone should be used ?
@JustFixinGarage Жыл бұрын
great tips
@deplorableraider8713 Жыл бұрын
Why not film the install ? Waste of my time .
@nunyabeezwax2198 Жыл бұрын
I totally agree! Worst how to ever!
@edw71182 жыл бұрын
How do you keep the intake looking like new? I have a rebuilt FI unit and needing tips to keep it nice! Thanks
@jakefriesenjake2 жыл бұрын
To get it looking new you need to drench in wd-40, and scrub with Brass wire brush. Then degrease it well. Then hit it with aluminum cleaning acid mix. Muratic acid and water can work. Or get some alumna-bright, aluminum acid cleaner used to clean big rig wheels and tanks. Spray on, and brush lightly with plastic brush. Hose off within 20 seconds. Keep hitting the aluminum with the acid mix till you get an even finish. If you leave it on too long, it can turn a bit dark on you. Rince really well and blow dry. Clean gasket surface with brake clean and install. Once installed, hit the intake lightly with silicone spray, wipe it in. Clean porous aluminum will stain easily, but if the pores are already clogged with silicone spray, well there you go! Also, spray down your carb base gasket with the same spray. Turns them into not stick!
@AR_4202 жыл бұрын
What is the engine bay sprayed with? Thank you
@shawnohiokarr2068 Жыл бұрын
Rocker guard and satin trim paint
@djeskandalo83942 жыл бұрын
Nice bike hard to find know in days.
@chickenfoundation93232 жыл бұрын
How does that fuel pump lever fit in the block?
@Joesmusclecargarage2 жыл бұрын
It doesn’t have to. It’s not a Chevy fuel pump.
@Jerem-xt9hl2 жыл бұрын
original cop car great
@BlacktoppPerformance2 жыл бұрын
I just did this to a 79 Camaro but used the original cover
@davidcolson66223 жыл бұрын
They just don't make em like that anymore.
@jefferywilder18483 жыл бұрын
Good Man with lots of talent! He has been a blessing in my life! Follow him!