How to install a new timing Cover on a Chevy SBC 350 without removing the oil pan .
Рет қаралды 31,592
3 жыл бұрынWorking on the 1980 Camaro . Fixed the timing issue and starting the reassembly of the engine.
@straighttimestirrups 10 ай бұрын
Would’ve be nice to see the cover with the tabs cut-off (before-after) photos and show how you actually installing it.
@CodyNelson-nightmoves 3 ай бұрын
Wish I would have watched this before before I tried to figure it out on my own as I went along. Now I got Niagara falls in the front of motor. I got two quarts of oil sitting in my cross member
@harrytaylor6081 Жыл бұрын
Thanks for the advice
@JustFixinGarage Жыл бұрын
great tips
@BlacktoppPerformance 2 жыл бұрын
I just did this to a 79 Camaro but used the original cover
@itzBiscuitsB 3 ай бұрын
what i needed to see was cut out some good info still but still searching
@genen.7370 Жыл бұрын
What type of silicone should be used ?
@AC.Prince 7 ай бұрын
Did that fuel pump fit? I've never seen one like that on a sb chevy
@edw7118 2 жыл бұрын
How do you keep the intake looking like new? I have a rebuilt FI unit and needing tips to keep it nice! Thanks
@jakefriesenjake 2 жыл бұрын
To get it looking new you need to drench in wd-40, and scrub with Brass wire brush. Then degrease it well. Then hit it with aluminum cleaning acid mix. Muratic acid and water can work. Or get some alumna-bright, aluminum acid cleaner used to clean big rig wheels and tanks. Spray on, and brush lightly with plastic brush. Hose off within 20 seconds. Keep hitting the aluminum with the acid mix till you get an even finish. If you leave it on too long, it can turn a bit dark on you. Rince really well and blow dry. Clean gasket surface with brake clean and install. Once installed, hit the intake lightly with silicone spray, wipe it in. Clean porous aluminum will stain easily, but if the pores are already clogged with silicone spray, well there you go! Also, spray down your carb base gasket with the same spray. Turns them into not stick!
@chickenfoundation9323 2 жыл бұрын
How does that fuel pump lever fit in the block?
@Joesmusclecargarage 2 жыл бұрын
It doesn’t have to. It’s not a Chevy fuel pump.
@AR_420 2 жыл бұрын
What is the engine bay sprayed with? Thank you
@shawnohiokarr2068 Жыл бұрын
Rocker guard and satin trim paint
@mrsuarez430 8 ай бұрын
Why so people say you have pull the oil pan lol I didn't have to even loosen it I have a 305 97
@s1mph0ny 7 ай бұрын
Some of the pans and timing covers are shaped different, especially the ones with 2-piece timing covers.
@Baron-Von-1973 4 ай бұрын
Why the fuck would you even think you need to remove the fucking oil pan??
@deplorableraider8713 Жыл бұрын
Why not film the install ? Waste of my time .
@nunyabeezwax2198 Жыл бұрын
I totally agree! Worst how to ever!
@vezina808 Жыл бұрын
How do you install the timing tab?
Fel-Pro Gaskets
Рет қаралды 148 М.
POWERNATION
Рет қаралды 1 МЛН
Motorcycology
Рет қаралды 2,4 М.
Sam’s Trucks
Рет қаралды 17 М.