Old Trane get replaced
2:22
14 күн бұрын
Rheem/Ruud in Garage
3:26
2 ай бұрын
Air handler base falling apart
4:41
RunTru by trane install
2:11
6 ай бұрын
Trane in Attic
4:21
6 ай бұрын
Old Goodman to New Rheem Select
3:33
Leaky Trane Invert Condenser Coil
3:50
Change Fan Blade on Rheem
17:20
4 жыл бұрын
Пікірлер
@renenunez1254
@renenunez1254 20 сағат бұрын
Liked that you insulated the condensate line, however, I don't see a trap, float switch or secondary pan. Talk to me....
@brian2coolful
@brian2coolful 19 сағат бұрын
The float switch is there , look good 3:50 , also here in south florida the drain line goes under ground and comes up outside .
@renenunez1254
@renenunez1254 3 сағат бұрын
@@brian2coolful Sorry, I missed the float switch. My system in the attic has a float switch on PRIMARY condensate line directly out of the coil, then a cleanout, followed by a trap and then a second cleanout and then runs outside through attic and a exterior wall and drops about a foot above the ground. The coil's secondary line runs into a secondary pan (under the unit) which also has a float switch and the secondary condensate line from this pan runs outside to the exterior soffit. I think I'm well protected from water damage or at least I hope so. Just a regular homeowner here in Texas.
@Topshelf786
@Topshelf786 9 күн бұрын
👏🏽 Reminds me of a young me in the field in more ways than one. Glad to see you sized plenum transition to the opening and not the whole cabinet 👍🏽🍻. Just subscribed 🫡
@alexvega514
@alexvega514 9 күн бұрын
You took to long fixing this ! i work in hvac and theres alot of ways doing this wirh ductborard easy
@victorortiz5761
@victorortiz5761 5 күн бұрын
Stop lying your just the helper. Brian is really good at what he does. I know this because I hire him often.
@alexvega514
@alexvega514 5 күн бұрын
@@victorortiz5761 Okay thats you! am jot sayind its bad ! it took alot time thats it.
@victorortiz5761
@victorortiz5761 5 күн бұрын
Your spelling is bad lol 😂
@alexvega514
@alexvega514 3 күн бұрын
@@victorortiz5761 yess Lol
@ricardojacquez3358
@ricardojacquez3358 12 күн бұрын
Beautiful work, all you need now is repair the wall full of knife scratches. Thanks.
@brian2coolful
@brian2coolful 12 күн бұрын
Thanks again ,the closet was repainted and the floor also redone
@b3d3g69
@b3d3g69 25 күн бұрын
Nice install!!!!
@JustMe-mn5hk
@JustMe-mn5hk Ай бұрын
No start collar no shiplap! Sorry, but that's wrong! You can't just make butt joints on duct board!
@brian2coolful
@brian2coolful Ай бұрын
I've nevee failed an inspection here doing it that way
@JustMe-mn5hk
@JustMe-mn5hk Ай бұрын
@@brian2coolful but you're failing AHRI and the manufacturer every time! Just because you pass inspection doesn't mean it's right!
@brian2coolful
@brian2coolful Ай бұрын
What would have you done differently?
@JustMe-mn5hk
@JustMe-mn5hk Ай бұрын
@@brian2coolful to start with if code doesn't require a flange around the top of the unit then I probably wouldn't worry about it either..lol.. but when I join duct board together I would cut a female shiplap on the existing duct board and a male shiplap on the new piece... also your corners should not be Butt jointed but also have a shiplap... with the air handler being on the interior I know it's not really a big deal.. but I'm in Florida and a lot of air handlers are in the garages and I can't begin to tell you the ones that sweat and leak air! Anyway it's good to see guys like you in the field... I've been in HVAC for 45 years fixing to retire and it's hard to find good replacement people! Keep doing what you do.. I didn't really mean to put you down! You certainly seem like you got a brain and you care.. that goes a long way! Stay safe and may your best days to be ahead of you!
@Topshelf786
@Topshelf786 9 күн бұрын
I have done both techniques. Wouldn't the mastic on the inside take care of the butt joint leaks?
@vmurr00
@vmurr00 Ай бұрын
why didnt you add a start collar
@vmurr00
@vmurr00 Ай бұрын
good video though man looks nice
@brian2coolful
@brian2coolful Ай бұрын
Not a common practice here in south florida , much different here
@vmurr00
@vmurr00 Ай бұрын
@@brian2coolful its very common in central florida its required here too but nice video man
@wiiiz3
@wiiiz3 Ай бұрын
Does thiz help to reduce sound transfer?
@brian2coolful
@brian2coolful Ай бұрын
In some cases, but specific in South florida
@Rado88
@Rado88 Ай бұрын
Those motors are so expensive
@brian2coolful
@brian2coolful Ай бұрын
Non warranty OEM parts will cost for sure
@josecruz3237
@josecruz3237 Ай бұрын
❤ Love it Great job 👏 🎉
@dominickwilliams927
@dominickwilliams927 Ай бұрын
That’s good work br
@PlumberGuy-ez9wx
@PlumberGuy-ez9wx 2 ай бұрын
Nice job, I would give a optional service to clean and seal where the concrete is exposed in the return. Make sure you're using pressure treated lumber for anything that touches concrete.
@PlumberGuy-ez9wx
@PlumberGuy-ez9wx 2 ай бұрын
Ive been getting into hvac. I do hydronic heating and one thing I noticed thats different is the quality of work between the two. Hvac guys get away with not sealing any of their joints or just using tape. building plenums out of fiber board. Using flex but never supporting and stretching it properly. This is just what I see locally, you did some nice work here. Wish they did it that nice in my house.
@cityboyz4life
@cityboyz4life 2 ай бұрын
Nice I like it
@nathantaylor680
@nathantaylor680 2 ай бұрын
Nice job on this video. Whats the spray at the end? looks like a glue what kind?
@ebenezerservices6363
@ebenezerservices6363 3 ай бұрын
Good job, do a video for elbows from scratch; it will be much appreciated.
@TX-EddyHVAC
@TX-EddyHVAC 3 ай бұрын
That looks clean, bro. Detailed, and it wasn't an eazy spot either. Good work
@brian2coolful
@brian2coolful 3 ай бұрын
Thanks
@scotts4125
@scotts4125 3 ай бұрын
You are good at what you do!
@airmechanical7163
@airmechanical7163 3 ай бұрын
You have the best video on how to make an offset. Well explained !
@freezetemp-hvac
@freezetemp-hvac 3 ай бұрын
👌🏽 impressive work sir 👏🏽
@brian2coolful
@brian2coolful 3 ай бұрын
Thanks much
@Jimmycarter7781
@Jimmycarter7781 3 ай бұрын
Thats was really fantastic brother
@brian2coolful
@brian2coolful 3 ай бұрын
Appreciate it
@Ageehvac
@Ageehvac 6 ай бұрын
Nice clean work man....
@brian2coolful
@brian2coolful 6 ай бұрын
Appreciate it
@MrGarcon98
@MrGarcon98 7 ай бұрын
in 2023 mine is out of balance its 17 years old but i keep it running model rpkb-048 jaz ,,,,,can i get one of these ? i am trying to RE balance it myself for now ,,,good video by the way
@ranimouf
@ranimouf 7 ай бұрын
Does anybody know the part# for this housing case? Thanks
@AnothaplanetZizzer
@AnothaplanetZizzer Жыл бұрын
Thanks for the tutorial. I am about to find out how easy or hard this is. I wish it was a bit warmer outside. Oh well. Time to give this a shot and hope I don't blow up.
@wolfmortimer1267
@wolfmortimer1267 2 жыл бұрын
Thanks for explaining