Pls sell me this in 1200 rs

Pour faire un pistolet airsoft 😅

Всякие общины делают по рассе, жить мирно сложно всем вместе? Все время распределение у людишек и войны

why brands using batteries like this and not like in smartphones

(TÜRKEY)

süper(TÜRKEY)

I would like to get or make such a charger and integrate it into the Parkside toolbox so that it is portable with six batteries ready to go is this possible?

Wtf 🤣🤣 why would you destroy a drill to make that piece if crap 🤣🤣🤣 ffs anything for views

gıreyat gıraftımanşip

Muy bueno el aporte ..pero también deberias poner el nombre del componente y su nomenclatura .. saludos

New here. Great Video! Looking for a sensorless BLDC 3 phase motor controller for a 12 volt 850 watt motor? any plans / pc boards I can try to build?

i have two 8ah parkside battery locked with unknown pin how to unlock them ? any idea ?

Pretty cool😁✌️

Creative video, thanks :) 👍

အခုအိုးစျေးတန်းလေးသိချင်လို့ပါဝယ်ချင်ပါတယ်

I was sort of hoping you'd show what mods you would make to the charging circuit. A stock sli charger will only give you about 80%

any body who wanna purchase this can contact me

How do you charge it

Would it not have made much more sense to use a 7S3P arrangement in order to get the full 20V PDO from the 65W module? You get the same amount of capacity and so long as the other modules can handle a voltage over 12V it allows you to use the 20V PDO for the entirety of the packs capacity pretty much. Only downside would be the BMS becomes more complicated...I like these style of 3S and 4S BMS for the ability to put the BMS at then end of a rectangular pack and just solder or spot weld the overhanging strips to the PCB.

Those parallel strips you added were totally pointless except the one on the main positive and negative...but since the current is being drawn from just one end of the strip it wasn't quite as effective as a pack that draws current from the entire length of the main positive and negative series. The series connections carry all the current from one group to the next. The parallel strips are only for balancing the cells in each parallel group to each other...so current along that path, especially with matching cells should be extremely small. I doubt you'd ever see 1A for more than 1 second at any point in time along those strips although the cells furthest from the BMS connections will be passing energy down towards the BMS during discharge and during charge the cells closest to the BMS connections will charge slightly faster than the cells furthest away from the BMS so there will be a small current flowing to help the end cells catch up. The only other point I can make I believe I've mentioned on another video. Your spot welding technique is ignoring the slits in the nickel. Its there to make the current go through the terminal and properly come out where the other electrode is. It has to do with current following the path of least resistance. When you have nickel with no slit the current might find it is an easier path to just shoot across the nickel strip and never really go into the cell's terminal creating a weaker weld. Granted, this is more important for pure nickel which is significantly harder to weld especially in the 0.20mm thick and up region. I never use nickel plated steel unless I'm out of pure nickel but if you are using pure nickel and struggling to get a REAL weld that tears nickel from the strip and leaves a weld nugget on the terminal (popping off with no holes in the nickel, no material left on the terminal is a BAD weld) try rotating the pack 90 degrees from how you did this one and put an electrode on either side of the slit. I'd say it increases the thickness of material you can weld by 0.05mm of pure nickel.

내가 찾는 게 여기 있었네요 ^^ Thanks~

A entrada é de quanto

Ese inversor es malo y con ganas, yo compré uno y en menos de un año se quemó y la potencia máxima que utilizaba era 1200w y el inversor de 3000w

Это уперается в голову на скотобойне и нажимается спуск.

何がしたいんだ！？

what spell did you do?!?

Seems like he's gonna repair it Him:

Если щётки немного провернуть по часовой или потив часовой стрелки то двигатель начнёт так же непрерывно разгоняться.

Many thanks for this video!

Can this handle a 140 mig inverter welding machine?

Нет защиты от переразряда. Аккумулятор может выйти из строя.

*Maybe my ax or mower blade, maybe.

Nguồn pin để ở ngoài vậy thì xấu để bên trong mới đẹp

mmmmmm

Можеш да ги измиеш направо.

Why did you connected that blue and black cable togeter and then shrinkwrap it? (min 6.20)

Porq mides en a.c amperaje si estas midiendo a una bateria dc y una fuente de alimentación

Berbahaya. cara ini bisa melukai anda

LIBERAR AUDIU

The bit 8s dull if when drilling it is small metal chips and not strands and you sharpened the hammer drill bit with a masonry blade

I think buying a new one is more worth it than repairing it. Because my skills aren't that great.

Comment on repart

Hardest part 😁

Stop mething around

What type of boiler do you have? Thanks.

What is all the equipment you're using to fix it is it expensive?

Hello Friend 👍❤️❤️👋

This is like the Final Boss of all the batteries you have reviewed Brother 😅 Jokes aside this is a hell of a battery pack. What caught my attention was that cells were ideally balanced and had low internal resistance. Dudes from AOlithium know how to do battery packs! Awesome, just awesome, and congrats Brother! ✌

Круто быть миллионером.