Great informative video! Does it feel safe when underneath the unit ? Is there anyway the lift could fail and or lower unexpectedly ?
@nicg887810 күн бұрын
Which pumps do you use?
@lastfanstanding99911 күн бұрын
Very impressive that's for sure...!😯🙏🇺🇸
@noahgiles777Ай бұрын
Looks really good. I would get the 02 assembly from More Beer and add oxygen to the wort as you transfer to the fermenter. The Blichmann sparge arm as you suggested would complete that brewery. Thats a sweet setup.
@operitivo4635Ай бұрын
Cool lab protocol at the end
@dbarrington1Ай бұрын
Do you have a link to that Pot Filler? It seams larger then most and with my 20 gallon 3 vessel system I need something with larger flow
@mikelopapa8139Ай бұрын
Could you link your air compressor?
@hellonwheelsuknow6556Ай бұрын
Very, very nice! Good job
@osorefreigerador3 ай бұрын
Excelente video . Extraordinario . Saludos desde Chile . 🇨🇱
@Gino202024 ай бұрын
Why kind of periodic maintenance is required for the lift?
@nextlevelmediaАй бұрын
Good question, I know it is supposed to be serviced periodically but I have never done it nor had any problems. I’m sure the hydraulic fluid should be changed at some point. I’ll have to contact my service rep.
@inhoc864 ай бұрын
Beautiful home brewery!! I'm in the planning stages of building my own dedicated brew space. What are the dimensions of your room?
@nextlevelmediaАй бұрын
Approximately 10’ x 14’
@ARtruthfinder14015 ай бұрын
How tall is the ceiling in the garage?
@nextlevelmediaАй бұрын
12ft high
@nmsauditor1a9505 ай бұрын
Try adding your grains first into the mash tun, then pump your water into the bottom of the mash tun. No dough balls. Great system. I use the same setup with 30-gallon Spike Brewing kettles. I built my entire system, including my control panel with Auber EZ Boil PID's. Spike Brewing was changing their handle design, moving them from the sides to front and back. I bought the 3 30 gallon last of the old inventory kettles for roughly $125 each and drilled them myself. Cheers!
@soonerborn90736 ай бұрын
I mean, it's nice but has ZERO drop protection like the Mous cases do for $50 less. The Mous case has strong foam all around the border inside a waterproof case so not only do you have rain protection you have really good drop protection.
@michaelwolpmann94536 ай бұрын
Very nice video. Do you feel that there is no need to bolt the posts to the floor? I think I still wouldn't trust it but that's cuz I have that kind of luck at times... ; o
@nextlevelmediaАй бұрын
Correct, no need to bolt a 4-post lift and confirmed with BendPak. I was definitely nervous but no longer after using it for some time now.
@PeterSchneemann6 ай бұрын
Can someone help me please? 1) Can you suggest any proven methods of installing such a lift in a garage that has a slope of at least 4-5 inches? 2) Also, would the lift shift if I don’t bolt it to the ground? (I would rather not anchor it as my concrete slab is only 4 inches thick.)
@nextlevelmediaАй бұрын
Definitely no need to bolt down. Most garages probably have a few inch decline - the installer would be able to speak to this or you can reach out to your specific lift rep - that would be the best resource. I don’t think it should be a problem.
@theghostofsw62766 ай бұрын
Anybody else wince when he just dropped that stir bar into it like that? lol
@BendPak_Media6 ай бұрын
Great Video! Thanks for sharing.
@authoritativebeer7 ай бұрын
I appreciate how meticulous, regimented, skilled, thorough and barefooted he is. That's courageous.
@SCBMD20202 ай бұрын
Some how i knew when i saw the set up that the brewer would be either barefoot or wearing sandals.
@TruckGoesVroom7 ай бұрын
Cute family! Thanks for showing the air compressor part
@ChadPrime697 ай бұрын
How’s it held up?
@nextlevelmediaАй бұрын
Great! No problems at all
@Striiket7 ай бұрын
I know this is an old video, but curious how the Tilt works with that SS fermenter? I had issues using the standard Tilt with my SB conical.
@nextlevelmediaАй бұрын
Haven’t had any problems with it and I always double check the OG with multiple devices and always matches up!
@jeremyrobinson44337 ай бұрын
Amazing video. Have you provided a list of the equipment in your brewery other than the link to the website you mention? I’ve gone there and it’s pretty comprehensive and would like to see your list.
@nextlevelmediaАй бұрын
I don’t actually have a comprehensive list as I pieced everything together over many months but maybe something worthwhile putting together
@jeremyrobinson44337 ай бұрын
I love this video so much. I’ve watched it multiple times. I’m looking at converting our second kitchen to a brewing room just like this. Love how organized it is and clean. Amazing set up.
@nextlevelmediaАй бұрын
Thanks for the comments! I need to get back in the brewery and shoot some more vids soon!
@eduardotudela8 ай бұрын
Hi, You have to peel off the blue plastic inside your grain mill. It’s only for protection purposes.
@nextlevelmediaАй бұрын
Ha I always wondered why it was blue inside!! 🍻
@elbertrobinson78708 ай бұрын
Have a bendpak 4 post recently acquired yet to install managed to find at a steep discount from a guy on Craig’s , had been looking for sometime have a scissor lift as well . With the loss of a garage space needed the added storage this offers , can’t wait to get it assembled . Great video very informative thank you Bert
@aussie4x4679 ай бұрын
This is a very nice setup. Congratulations.
@coalacorey9 ай бұрын
Insane setup, thanks for the tour!
@pwrshots10 ай бұрын
My wife freaks out when I get under my car with jacks. Lol. Considering a benpak. Tired of jacking up each wheel.
@bal4cars10 ай бұрын
what size is your garage
@mikeullmer322511 ай бұрын
Love the build! What are you using for bulkheads where the trunk line goes through the collar? Is it insulated?
@nextlevelmedia10 ай бұрын
I used mahogany wood 1x with two pieces and spray foam insulation in the middle
@josefnalbant11 ай бұрын
Thanks for sharing, where did u get this alu ramp? And what was the price for the lift ?
@nextlevelmedia10 ай бұрын
I bought the lightweight aluminum ramps from bendpak and the lift cost around $5k all in including shipping and installation
@bprz06715 күн бұрын
@@nextlevelmedia Can you say how much just the install cost?
@willd284 Жыл бұрын
Awesome setup. I’m about to transition to an electric 10 gal system. I just upgraded to a larger fermenter with a peltier cooling system.
@nextlevelmedia10 ай бұрын
Nice!
@jpcii Жыл бұрын
I am considering buying the new jacketed SS brewtech fermenter. After about 100 batches, the cooling coil has a fine layer of beer stone that is not coming off. The inside of the fermenter is pristine. Gives me an excuse to buy a toy. 😂
@nextlevelmedia10 ай бұрын
It’s a top quality toy you won’t regret it!
@scottayling5835 Жыл бұрын
Brewery goals this ansaloute top notch
@nextlevelmedia Жыл бұрын
Thanks!
@samuelhughes4108 Жыл бұрын
Very nice setup! Appreciate the organization and clean design
@nextlevelmedia Жыл бұрын
🙌
@lgopal3921 Жыл бұрын
it is an excellent operation system to make craft beer
@nextlevelmedia Жыл бұрын
Appreciate it!
@daveh2557 Жыл бұрын
Nice setup! Have the same lift. The support strap under the drivers side ramp has 2 large bolts on the bottom. Do the bolts dig into the Swisstrax? Mine chews up the floor every time the lift is lowered.
@nextlevelmedia Жыл бұрын
Yep same for me, luckily it stays in the same location. I tried contacting bendpak to address and come up with solution but got bounced around to the wrong people I guess. If you know a welder they could take care of it easily.
@daveh2557 Жыл бұрын
Bendpak has a fix with a lower profile bolt that I recently received. Sent it free of charge.
@ryani5103 Жыл бұрын
12 hours later…
@nextlevelmedia Жыл бұрын
Takes about 8 hrs start to finish including clean-up
@brijkotecha8300 Жыл бұрын
Useful, thank you.
@nextlevelmedia Жыл бұрын
You're welcome!
@JoshEAllen Жыл бұрын
Do you have any regrets putting these on top of your SwissTrax? Do you have issues cleaning underneath them?
@nextlevelmedia Жыл бұрын
Na no problems I just use the leaf blower to blow anything out or my dyson vacuum to get underneath
@jjs3656 Жыл бұрын
Do yo mind sharing total purchase cost for this particular option (w/all the accessories)? Thx
@nextlevelmedia Жыл бұрын
It was right around $5k all in including delivery and install
@stevehobbs1759 Жыл бұрын
Thanks for the detailed video John. The Viper is undoubtedly first class, however I’m curious whether you miss the height adjust feature offered by your sonic chair
@nextlevelmedia Жыл бұрын
I don’t miss it at all for this particular chair as I just utilize it to roll around my car for detailed and cleaning the wheels, etc
@surgicalmotorsports Жыл бұрын
Thanks for the video. Nice garage!
@nextlevelmedia Жыл бұрын
Thanks!
@tomfaro6259 Жыл бұрын
The main problem I have with bend pak is everything needed is optional. Outrageous in my mind.
@nextlevelmedia Жыл бұрын
Agreed you can definitely get the same setup for maybe half the cost but the safety features and engineering on this make it worth it in my opinion.
@mateo_del_norte Жыл бұрын
Nice, looks great!
@nextlevelmedia Жыл бұрын
Thanks!
@davidpestana5290 Жыл бұрын
the entire vide reminded me how poor I am
@nextlevelmedia Жыл бұрын
You can definitely build a budget setup or build slowly over time
@rogeriosaskuat Жыл бұрын
Congrats! Nice job
@nextlevelmedia Жыл бұрын
Thanks 🍻
@tradetop007 Жыл бұрын
Mill some grain, heat some water, close and open some valves, and you have happiness fluid at the end :)
@nextlevelmedia Жыл бұрын
Cheers 🍻
@Ladarioproducoes Жыл бұрын
This garage is really cool, I can see that you have some money, from this garage I would only have the wheel supports.