Ye kaha milega

Hi what is the best parts shop to buy this

Thanks it worked a treat Peugeot 3008

I would like to know how you cut a piece of plastic

Could it be used for the oxycut torch?

Those generators are not "free" as they do need replacement of the molecular sieves and filters, which can get pricey, and they have a very limited flow rate and pressure, so you are generally limited to smaller tip sizes and heat output and forget about cutting.. Definitely useful for hobby use, but that said, that little "micro torch" is probably the most useful torch on the bench. Very concentrated pinpoint flame and low flow, so works perfectly with a medical oxygen generator and even the disposable oxygen bottles last for hours of use vs. the other styles of torches where the tips are really too big given the size of the canisters: a full oxygen canister basically lasts for only about 10 minutes of really decent heat, which may be enough for a couple of small brazing repairs, but which is not really economical for actual welding or cutting.. What you might want to investigate are HHO torches, which basically run on distilled water and potassium hydroxide drain cleaner. These use electrolysis to separate hydrogen and oxygen and then you recombine them in a torch and are used extensively in the jewelery industry, and after paying for the machine (or making your own, they are not hard to make) are probably the closest thing to truly "free" welding there is...

I hve seen them bolted to a wooden pallet. I will try that.

That will never stay put when trying to lever a tyre off

I have oxy propane for heating and cutting, but was told you can't weld steel with it because it produces a brittle weld ? Something to do with the hydrogen atoms not burning in the flame, but becoming deposited in the weld ? 🤷‍♂️

@AndyFireBlade - Medical oxygen generators aren't ideal for welding because at max flow purity dramatically decreases.

Really interesting to see the different setups. You are like me, looking for different solutions. Just need to work out how to get enough pressure & flow for my oxy propane cutting. ; )

Great idea and find. Like you say the flow rate would be an issue for bigger jobs. Could you build a small gasometer (gas holder) with the water seal method to store the oxygen till it’s needed ? BOC bottle rental is a killer for hobbyists, that’s why I do MMA welding at home.

I do want to caution about exchanging regulators & hoses between Acetylene and Propane. Depending on what grade your hoses are they may prematurely breakdown in less than a year. Search Keywords “crossco selecting a welding hose.pdf” Decent overview of Torch Fuel Hose Grades with “R” & “RM” are Acetylene Only while “T” is rated for all common fuel gases. Outside of the actual hoses, while using an Acetylene Regulator for Propane is usually possible [Since most modern manufacturers use (neoprene?) diaphragms in both] you should never try to adapt a propane regulator to run Acetylene since the all important safety feature of a 15PSI Max output won’t be inherently built in (not really aplicable in your example but important info for hobbyists).

Great idea. I think I'll buy one for my shop.

The red is for the flattest part of the tire. Yellow is for the lightest part. I had to look it up from Yokohoma. Often red and yellow are quite close together on the tire. I found all of this to be insignificant if you plan on balancing the tire. This video does not show the state of the balance. You just need a bulls eye bubble level and sticky weights to balance it.

Smart ! Would the same kind of work work with the tepee/multispaces ? they've got two seats at the front however not 3

This is genius

The oxygen machine works by using a chemical reaction and eventually the necessary chemical which is built into the machine will run out and the machine will then no longer work. It is not free. The refurbishing companies that supply these machines recharge the chemical reagent (I believe) since the motors and electronics are perpetual. It is interesting to see that they can work in a welding or brazing application on a small scale.

Rather than PTFE tape Loctite produce a 567 or 577 sealant, far easier to employ which does not set.

Having a gas can sat on the bench whilst you use that torch isn't a good idea surely?

looks like a rip off of a Smiths little torch. the best thing about using an oxygen concentrators is they do not enrich the oxygen concentration of the room. if anything they reduce the oxygen in the room by burning it faster in the flame. Had a real smiths little torch for years with a concentrator works great, i wonder if the rip offs work as well. for the largest flame a rose bud tip is great if you can keep the oxygen flow rate up.

Oxygen leaks do matter. Things that normally do not burn very well or easily will burn vigorously in an oxygen-rich environment.

Better to use soapy water in a mist spray rathan than sniff test 😊. Nice little torch.

propalene is good, its liqued rather than dissolved (as in acetlene) so get nice full bottle, burns hotter than propane. not easy to get hold of though.

mapp gas is not what it used to be, modern version is only about30 degree hotter flame, not worth the extra expense.

look up hobeyweld and rental free gas bottles. you pay a one off refundable deposit and buy the gas with no monthly rental, way cheaper than boc or linde

That is stunning, absolutely beautiful condition

Now all you're lacking is an acetylene generator ...

Put the combustion intake outside the box

Ive got a 2016 Peugeot partner teepee, didn't work for me unfortunately.

Hi , love the video how many Lt per minute does your machine give out, and what’s the least you would recommend? Manny thanks. Paul 👍👍

Thank you so much. I did and it work.

Hi Andy iv got a partner 1.6hdi .can you please tell me what gearbox oil I need for it.its 2012 .there so many different people saying different grades/halfords come up with 80/90 and there gl4 gl5 .you seem to know your cars so thought I’d ask thankyou

Merci pour la demo.

So there's no regulator . That's interesting.

Hi Andy. Glad to see another enthusiast doing their own tires!! I have a somewhat similar set up. Thought you might like to see it in action kzfaq.info/get/bejne/jc2agbJjzNqXqJs.html

Hi can I weld a bmx steel frame together with it

Wowww… just did this now. It worked. You hv saved me some pounds to pay to mechanic. Thank u

My favorite car on Gran Turismo

What about a CRF250 rally???😊

My friend John owns this beauty. 👍

With an Peugeot Partner tepee2 NO SUCCÈS🤔

My car years ago back in mid 80s

Very nice i would have one just for the sound

Beautiful cars , I had the 2.7 straight 6 in silver

Font for “Esprit” looks same as if not very similar to “Mexico”on Ford escorts, anyone know more about this?

I think I saw this very same car at the Oct 2021 NEC Classic Car show, flanked by a red Europa and a black Elise on either side. There was another white-over-tartan James Bond - spec S1 in the show, cordoned off in another hall. Silver over black really suits this car and evoques the 1972 M70 concept car ("the silver car"). What's it worth? In this condition, I'd say £70k.

Oh brilliant, I have tons of Milliput due to crafting and have a leak so I will turn off water, locate leak and cover it with Milliput!

Gorgeous car! Don't look at the door handles either. They're from an Austin Maxi. Doesn't matter though does it? No Austin Maxi went as fast, or was as stylish as the Esprit.

Most beautiful car, shame about the wing mirrors in those days.