thanks for making the video

Good idea

That's the exact noise on my 15 Sierra! Son of.......

He left a big hold on the copper to aluminum. That is not flux .

Hope you get a million views

GREAT JOB!!! WHERE CAN I GET TORCH HEAD LIKE YOURS??

Nice one man

I have no idea what i just watched but this is peak content

Thank God I seen this video 🙌🏽 I have the same issue on my 2011 suburban ltz

Thaks for the video. Do you still prefer the Reme Halo? What about maintenance costs? The Reme is pretty expensive to replace bulbs and stuff. Iwave has no parts to replace and it self cleans.

Guys my does almost like that but it’s more of a rattle, not ticking like, it’s like a rattle and it starts but then goes away or stays for a while but it’s goes away!!

Nice video!

You will begin to see a red "corona" in the flame as the aluminum comes up to temperature. You see red in your flame, dip the solder!

From your history of technical experience... which one has the best track record for removing odors?

How can I contact you? Do you have an instagram?

This was very helpful! Could you do a video on coil uv lights? wiring transformer?

We love them hose 😂

Hi can you give me the full name of this brazing rods?

Thanks, this video had a ton of useful info

It might have been easier to use the multitude to get a clean-cut for the repair. Less damage to the fins

I have a pioneer 18k unit with a 40’ linset that I added additional r410a when installed. I want to move the unit to a different location because of a remodel. Will the unit only hold the amount for a 25’ linset when I pump it down or do I need to buy a tank to store the additional coolant?

Have a 2016 Suburban with the 5.3. $8900.00 later, we have new LIFTERS and a camshaft installed. Cylinder deactivation lifter failed. Old school lifters don't fail.

So far those LS engines seem to have ALOT of issues. I have come across two with ONLY 146k-148k with some kind of engine knock or noise in lower end.

Sounds like a diesel lol.

What seer is this? Is it a heatpump?

No, at what time did you say to use flux?

Looks like you ended up taking off the heat shield. Lol

I’m swapping my bolts out before they go bad!!!

Good demonstration! My experience with doing aluminum always turned out awful. The biggest difference I see is you are using a propane torch as opposed to an oxy acetylene rig os heat is more manageable.

Damn I love youtube. I had no idea what that noise was. Thanks!!!

So reme halo led would be best of some one w asthma?

Dang nice job

Lol sounds exactly like mine at 5am on a 40 degree morning then it warms up and disappears thanks for the ideas

Right before u shut off the system, the gauge didn’t reach 0. It looks as it’s around 10 psi. So it is okay right? And does it mean we lose a little bit of Freon on every pump down? Lastly. Can the flares be reused? Or it’s best to make a new flare?

No Amps, it's voltage. The system is probably only drawing about 20 amps. The electronic disconnect is monitoring voltage to open the contacts if voltage goes above or below the set points.

I couldn't figure it out for 2 years now.... I went and checked my 2014 also.... And its the same two bolts.... I can't wait to get a quote lol

great video. thank you!

Thank you for this video! I was having the same issue and thought it was bad lifters, well I inspected and saw both rear exhaust manifold bolts missing and black soot. The damn truck is only 4 years old.. why is this so common? Come on GM! do better!

Aren't these competing products? Are you recommending installing all 3 or just showing 3 different systems?

Thank you do you have the link for the bolts by any chance?

Have same noise, and when accelerating I can hear it also like from a dead stop. But, all my bolts are in and I even put a socket on them just to make sure. So, same noise but different location I guess. Any ideas on where else it could come from.

Ayooooooooo thank you for posting this mine does the same thing I was thinking I had a lifter going

Thanks for doing this video! Still working okay?

What kind of torch u use I could Bay this with no problem at the store got the same thing my truck is leaking nd I try everything.

💪💪💪💪

Hi , great video . How is the water bump for this Brand ?

❤️🇵🇷

I have the same ? Did you find out

awesome video!! thank you!! --- side note-- ive heard you can use one of the 4 pulley bolts, to ease the pump out if its stuck