After I change diesel filter the car worked fine for some hours. But when turned off for some hours the diesel are "gone" from the filter. Making it impossible to start up again... Strange error
@barnibara88272 күн бұрын
Hi there, had the same issue with my car, same car just from 2009, I've put a brand new egg valve in and cleaned everything but the engine management light keeps coming back on with the same error code, and the car feels jerky in 2nd and 3rd gear at around 2000 rpm, got the car down to the garage they erased the fault codes but about 30 mins later came back again...what's the solution
@stanhopeautorepaircentrewardak2 күн бұрын
The EGR valve could be defective, and it should be investigated by a professional technician. Do not replace it straight away, prove the defectness
@barnibara88272 күн бұрын
@@stanhopeautorepaircentrewardak I've put a new one in already about 3 weeks ago, cleared the codes 3 times after that, how do I prove that it's got a defect
@jonaslandin74452 күн бұрын
Great video thanks!
@stanhopeautorepaircentrewardak2 күн бұрын
Thanks for watching our channel
@kora257192 күн бұрын
Hi, i have i40 1.7 crdi and my start stop light blinks then stays on when i start the car A with circle light, it gets the same code as on this car, also the battery is at 12.2 to 12.4 volts constant, alternator voltage is at 13.7 to 14 v. Also the light goes away and sometimes stays on
@TukanCustoms3 күн бұрын
Holy crap i just removed 2 thermostat screws from my 2.0 cfgc engine yesterday without stripping anything from the engine and it takes around 2h cause its so tight there.... after watching this video i'll leave it till next weekend cause its not that easy as i thought it will 🫥 Thanks for that, otherwise i'll probably trying to replace it today and will stay without the car as is my only one now and need it to work tomorrow. Crap.
@stanhopeautorepaircentrewardak3 күн бұрын
Thanks for watching our channel
@neoniamo93436 күн бұрын
Thanks man. Nice video,good luck
@stanhopeautorepaircentrewardak5 күн бұрын
Thanks for watching our channel ☺️
@user-ww4mg9km6w7 күн бұрын
How can I unlock the crash data headrest? Yes?
@bootybandy7 күн бұрын
When torquing down the bolts/screws, you should always do it in a diagonal pattern and not sequential. That could distort the mating surfaces?
@pablobon59577 күн бұрын
How much do you charge for a job like this one? I gotta do it and also take out intake manifold and clean it
@stanhopeautorepaircentrewardak6 күн бұрын
Are you sure that your car's problem is the same as this one?
@salihsabanovic61617 күн бұрын
Da li pumpa u rezervoaru treba stalno da radi ili?
@stanhopeautorepaircentrewardak6 күн бұрын
You just prime the fuel system and the priming will fill the fuel filter up then put the original relay back on and crank the engine over, when the original relay is on, as soon as you crank the engine with ignition key the fuel pump is going to start pumping fuel to the fuel filter.
@user-st4yx8uh3h8 күн бұрын
I have the same car with the exact same issue fuse all look good
@rollsroycess13 күн бұрын
Excellent video sir. In my Smart fortwo 451, I don't have the oil pressure sensor either, since it probably broke when the belt was cut. Anyway, even without the sensor, in my car, the oil pressure light, It turns on and then turns off, it's no problem. I'm about to buy the sensor and I'm going to change it as soon as possible, the only problem is that they covered the hole where the sensor goes with Poxipol and I don't know how I'm going to get it out. Any suggestions? Regards
@WiSeNhEiMeR-136915 күн бұрын
yikes ! thanks COOP ...
@stanhopeautorepaircentrewardak15 күн бұрын
Thanks for watching our channel
@mukeshkumar-iv5su15 күн бұрын
209 modle
@moffatk794819 күн бұрын
Hi great video. I have the similar VW TDI 2.0 CFF engine, that have the problem of temperature only going upto 75 degrees. It now winter where I stay it takes long to warmup. I am thinking of doing this job. Does this car with a manual transmission like this one not have the 2nd thermostat like the DSG transmission?
@markusm.815621 күн бұрын
The key scenes in the video are very good for understanding what needs to be done to remove the oil pan. Other KZfaqrs don't show scenes that show what's important. Big thanks
@stanhopeautorepaircentrewardak20 күн бұрын
Thanks for watching our channel
@mosoeumokhele806124 күн бұрын
What happens if you don't program new codew, are we still gonna experience same problem with a car as before?
@bahramzangene551925 күн бұрын
Awsome
@stanhopeautorepaircentrewardak25 күн бұрын
Thanks for watching our channel ☺️
@alexyoung376826 күн бұрын
Hi mate I did the timing belt today then I went to rotate it twice, the engine won't turn can resetting the timing fix this ? The Haynes manual did not have the timing marks for the top left one 11oclock. I used both tools for the right and bottom ones to lock them
@Adrian92.29 күн бұрын
One more question, when to put it Back, what are the stpes? Doea it need to be adjuested? Or Something like this.tx
@Adrian92.29 күн бұрын
Bro youre the best, have the same engine and i searched for this 🙏🏼
@robertpalmer5803Ай бұрын
Lovely video...ive done one...not a job for the faint hearted...that electric plug on top of the gearbox is very difficult to remove....Bob...Paignton....
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel ☺️
@eoghanhennessy443Ай бұрын
Was there breather issues with this car causing misfire and oil pressure
@russellmcallister6830Ай бұрын
Hi what did you use here for wiring diagram. How do access the software please. Thank you
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel. It is called AutoData.
@mohammedaamirkhan6159Ай бұрын
Hi i changed the fuel filter in my audi q7 engine code bug the spring came out i pushed it back in while closing and forgot to prime it car started and drove for 10mins parked it up now wont start what could be issue
@abbas1786Ай бұрын
Hi I have same problem do I change the whole throttle body
@5455jmАй бұрын
just sent this to my mechanic; thank you so much😁
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel ☺️
@raquelramos7705Ай бұрын
My Peugeot 208 1.6 HDI gives 700 miles warning. But Adblue has been added and tank is full. Will I be able to continue driving past 700 miles? (had NOX sensor changed and still didn't fix the problem)
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel You need to relearn it to the vehicle engine ECU by a capable diagnostictool. There is another fluid used in this vehicle called DPF fluid. Confusion occurs sometimes, distinguishing between adblue and DPF fluid , which one the message is for, topping up adblue doesn’t require relearning procedure but topping up DPF (fat fluid) does require relearning procedure plus resetting the nox sensor.
@tuzdiyarlfurkan4237Ай бұрын
Which engine code was this car?
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel I can't remember the engine code.
@waldemar31293Ай бұрын
You always replace the water pump with the water pump housing. Usually the housing is the part that is leaking, not the pump. If you buy it original, the water pump always comes with the housing.
@carlosselvoni1513Ай бұрын
change cooler i have the same problem i change cooler and very good after
@giovannipg3000Ай бұрын
How to fix back pressure engine ???
@warrior6882Ай бұрын
Subbed
@JustinLT212Ай бұрын
15:38
@sosocopacabana2809Ай бұрын
Bonjour, je voulais savoir j'avais un voyant moteur allumé sur ma audi A3 2008 140ch qui m'indiquai la pompe a eau auditionel, du coup je l'ai remplacé par une neuve et ensuite je l'est retirer avec la valise mais le voyant moteur ce remet, du coup je sais pas le problème peut venir de quoi on ma dit peut-être le relais, ou le faisceau
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel. First, check the fuse if the fuse is alive. If the fuse is blown after replacing it, then follow the steps below: Disconnect N422 (solenoid)located on the bulkhead on the passenger side RH drive vehicle) it is just beneath the water repellent cover beside the wiper arm, and see if if the fuse stays alive because fuse numbers 14 powers up V400 and N422.
@sosocopacabana2809Ай бұрын
@@stanhopeautorepaircentrewardak demain j’irai contrôler tous ça merci pour ces informations
@speedshedАй бұрын
Hello, I replaced hp fuel pump and now get diesel right up to the hp fuel pump but can’t get diesel past the pump and to the fuel rail? Any ideas what I’ve done wrong?
@kristianhristov6182Ай бұрын
If it appears after oil change, check your filter, you probably broke the stick on the filter.
@fazalrahmanhamidi3677Ай бұрын
Your address?
@stanhopeautorepaircentrewardakАй бұрын
maps.app.goo.gl/53aWYLMZJ5Q5tKGS7
@CcorniitАй бұрын
How does the metal swarf get through that dense screen? That screen looks clean, it should be clogged with the swarf as well?
@CcorniitАй бұрын
Where did all those metal filings come to the fuel rail? Had the HPFP failed catastrophically?
@stanhopeautorepaircentrewardakАй бұрын
HPFP plunger cam lobe.
@TocyBloxАй бұрын
The new revised EGR NEED TO BE PROGRAMMED!!! Just do it at the dealership. Also they have an updated intake manifold too. But they have programs that covers either or Both. This is really important!
@user-ru1he1if8qАй бұрын
дякую за відео все гарно розяснено
@Yoilurwelcome452Ай бұрын
I just bought this exact car n just got done replacing my hose and new thermostat and still having low coolant issues and overheating
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel
@zambozambo2688Ай бұрын
How did you take off the flap motor off? i trying tooo take it off but there one screw under near the lamda sensor i can not take it off
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel I did not skip any part of that task, but if i did, i might have explained how it can be done, i have done this job a long time ago, and i can't remember how did i do it . Look at the service manual pages related to the task i have recorded and uploaded within the task being carried out.
@sergeybishir-zd1hqАй бұрын
Hi can you fix this module 722.8 after repaired I got the fault 0602 Control module Continuously variable automatic transmission (CVT) is not coded. 0710 The signal from component Y3/9b2 (CVT (continuously variable automatic transmission) temperature sensor) is not available 062f Control unit Continuously variable automatic transmission (CVT) is defective.
@F0rdy57Ай бұрын
Do you have a video where you recondition these or even refit them? Awesome video 😊
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel. No, unfortunately.
@im-dt2erАй бұрын
How big a job is removing the Turbocharger?
@stanhopeautorepaircentrewardakАй бұрын
Thanks for watching our channel. Service manual gives 1.8 (1 hour and 48 minutes), removing and reinstalling.
@mantasserapinas53222 ай бұрын
if my car f31 it work or no? thanks big help
@stanhopeautorepaircentrewardak2 ай бұрын
Thanks for watching our channel ☺️
@mantasserapinas53222 ай бұрын
@@stanhopeautorepaircentrewardak very good video, keep going, can't explain how much you helped me
@tomas615982 ай бұрын
Nice vidoe, helped me, very thanks much!
@stanhopeautorepaircentrewardak2 ай бұрын
Thanks for watching our channel ☺️
@davesmith67342 ай бұрын
Great channel very helpful. What software are you using to check wiring diagrams and fuess. Thank you in advance Dave
@stanhopeautorepaircentrewardak2 ай бұрын
Thanks for watching our channel Elsawin, UK based Autodata.