Nice video Can this be done for V60 2012?? Thank you..

Actually, this is what i needed to get the carpet up. Thanks!

Wooden cloths pegs do the trick , NO scratch's

Bad very Bad what you do

Simple and easy to understand. Awesome man, thank you

Obrigado pelo vídeo

Spot on many thanks ✅

Video ist sehr hilfreich . Wichtig dabei wäre noch zu erwähnen das man diese Aktion auf keinen Fall bei kaltem Wetter machen sollte da dann die Plastikclipse auf jeden Fall brechen . Und diese Clipse bei Hyundai zu kaufen heißt nen vollen Geldbeutel mitzunehmen . Denn die kosten nicht gerade wenig .

Can the solenoid coils be replaced on a Volvo S60R BCM?

Thanks for the video! This cleared all my BCM faults and ABS light went out. I used a knife and heater to open it a bit nicer, and soldered all the contacts.

how get screen out to see power ports lookig t o get a screen double din fitted into i10 2016 1,2 se

Which cables carry the audio signal? Want to install an active sub but keep the original head unit. Which cables should i connect the sub to?

hi mate where did you get this from

Thank you 💛

I respect the repair but using expoxy is not fuel resistant, gas can actually seep and eat thru expoxy, permatex gasket maker fuel resistance is the way to go, it’s 100% fuel resistance. Peace

Đây là cách làm mất thời gian nhất, dễ bị chầy xước nhất có nhiều cách tối ưu hơn nhiều đảm bảo 100/ trăm ko trầy tap lo

If anyone has this nowadays, I found a few tricks that will help you out to make it smoother. Get a 5mm Torx wrench head and a small enough driver (I got a somewhat 50mm handle which is perfect for the confined spaces like this, have an extender ready as a brake tube tends to get in the way when dealing with one of the screws). Do not cut the enclosure! Use a heat gun or a blowtorch to soften the seal and carefully cut and scoop it out, it takes time yet you'll end up with an (almost) intact cover. The pins should be soldered probably, yet I had a different issue so just measured the resistance and left them alone. As my issue seems to be a rather common one, here she goes: at times you can get a coolant leak from a hose down there (usually the one coming from the air heater), making the coolant end up on the transmission and evaporating right onto the BCM. There is a vent hole with a moisture-proof insert, yet it will still let he coolant vapors in, shorting the electronics (usually the crystal fails first, as it is the most sensitive to any stray resistance, causing a brief general HS CAN failure and a persistent "BCM NOT CHECKED" state along with the ABS, brakes and MIL lights and a brake failure message. Open the box, rinse with a non-agressive solvent, check the soldering (mine was ok) and the resistance (measure between the leads and the PCB, and, for the common negative connections, between the interconnected pins) - and seal it back (I used a silicone gasket maker that is rated for thick seams).

This is like kicking the TV when it doesn't work... it might do the trick, but for how long?

Hay que tener lista toda la cuchilería

I don`t understand the reason to unplug and disconnect eveything. I would clean everything with break clean. It dries faster and you have a perfect result. And you don`t have the risk to damage smth. 🤷‍♂ Kind regards from Germany; sorry for my awful English!

Nice

So the real problem is only this ! I must di to my e 36 same modul ate

Just replace it. Don’t be a gomer.

Genial!!!

Can u fix a pen hole on a fuel pump

Good

My Ford five hundred leaks gas. I mean that if I put over 6 -7 gallons of gas, it literally pours out from underneath the rear passenger seat. Would this help?

Dhanawad bhai

Think you

Can this be done in a garage with the door closed or should this work be done outside?

I just did this and no more BCM 0070 code, I soldered all the connections too. Had to get my iron really hot but it worked. What I recommend is to use a heat gun and a knife and cut out all the sealer. Work your way around. Once the black sealant is removed, heat up again and cut along with a knife. Then heat a little more a use a pry tool or flat screwdriver and the top will come off alot cleaner.

Thanks for a video! Looked like sealed unit and not possible to open up after the first look. I did manage to open it gently with some patience and heatgun. Used the fine soldering iron tip and the microscope to repair each pin. Happy days :D

Great video! 😁 does my 99 XC 70 cross country have this access panel? I am really hoping so

Is it made by Russians?

Bhai grand I10 ambient light installation ka video banana

Y decían que el cuchillo de mantequilla no servia para nada 🤣

👌👍👍👍

kzfaq.info/get/bejne/mJx-iKijlt_Zo6s.html đây mới là cách hay nhất

Рукожоп 87 уровня конечно ... Я бы постеснялся такую работу на ютуб выкладывать.

Thanks for the update. I will probable look to use a seal more compatible with gas. Thanks

Hello Might be better to have your original part repaired at www.upfix.com Here is the service link www.upfix.com/product-category/repair-return/abs-modules-repair/

00:29 What we call those yellow lock clips? Plz let me know I need to buy those.

STOP BLOODY SQUEAKING.... yeah the noise is annoying as hell aint it LOL. i gotta do this to mine what a bloody job i might solder mine or is that been tried and failed again in the long run?

What kind of sealer did you use?

You destroyed it. Better off sending it to MidWest ABS and let him fix it right. midwest-abs.com/

Is there a way to remove just the module from the car? And would I have to bleed the brakes system with this part removed? Thanks.

кошмар, руки бы тебе оборвать за такое вскрытие, не умеешь, не берись

But did it correct problem, and why not just take out the cover where connections are and not take off whole cover when the connections that are exposed are at the end where the first part of cover was removed.

Nopee, its not there on my volvo :(

Nice vid. Does anyone have a video from an Alfa Gt 2.0 jts 2006? i smell petrol but im not aware how to reach the pump