My son's 2010 Jeep Liberty was overheating. Turns out it was the radiator cap was no good.
@desiseveright4 күн бұрын
Grinding the frame worked for me, 2024.
@amystrickland95257 күн бұрын
War Eagle!!!
@WatsonsWagons7 күн бұрын
@@amystrickland9525 War Eagle!
@matopezuta205017 күн бұрын
I did the same mod for the window used thumb screws instead of wing nuts so the top of the machine screws are flush with them to eliminate snags. I left off the plexiglass and just have the tempered glass since the plexiglass scratched as fast as the inside clouded up. One trick to make the glass inside last longer is to coat it with 2" painters tape. Score it every 8" and just peal off another one when the opening fogs over.
@mikimiki19518 күн бұрын
Where do you hook cover on concrete is there something pre installed when concrete was done
@WatsonsModels18 күн бұрын
No, after the concrete is poured and settled I had to use a hammer drill to bore out holes to tap in the anchors
@mikimiki19518 күн бұрын
@@WatsonsModels thank you
@dylanalexander650319 күн бұрын
Thanks so much you just saved me so much time and money. This is coming from someone who is not at all mechanically inclined.
@jeffd.761820 күн бұрын
I have a 2014 with the 4.3 v6 and I have the same issue with my passenger rear bolt, my biggest issue is I can’t find a repair bracket for this engine, everything I can find is for v8’s, is there one out there for a v6 or can someone make one?
@WatsonsModels19 күн бұрын
Yeah, I’m not sure when I get stuck like that. I just start rolling with eBay and try different search terms.
@danzielinski503620 күн бұрын
I got the same kit especially because of the FULL interior. FANTASTIC KIT! BUT aside from the issues You pointed out like the lack of exposure of detailed areas, My only issue is some of the directions don't show the installation of every part. what was seen in step 7 post assembly wasn't seen installed in step 6. AWESOME KIT! ! ! would I build another ? Absolutely Nearly done with mine now I need to cut out some of thoose rear deck pannels as you did.
@WatsonsModels19 күн бұрын
Cool
@eweuflesu2320 күн бұрын
How do you know which one to replace if they are all flickering or dimmer or not lighting at all? It looked like you may have gotten lucky. Or do you start from the bottom left and replace them until they all come on?
@WatsonsModels18 күн бұрын
Unplug one at a time and insert the new light. It’s the only way to eliminate where the bad one is. So unplugged the first one plug in the new light see if it makes a difference if it doesn’t plug in the old light and moved to the next one no need to replace all of them. I wasn’t lucky the particular light that I had was flickering and then it eventually stopped so I knew which one it was.
@johnnyrestrepo101323 күн бұрын
I just did exactly what this gentleman did on the video and it work perfectly. I had to drain my pool about 10” bcs i over did it with salt once you get it around 3000-3300 the cell will work. Thank you
@WatsonsWagons23 күн бұрын
@@johnnyrestrepo1013 wow I made gentleman status. Thank you. I’m glad this was helpful.
@willthorson454325 күн бұрын
Andys blows the hobbyboss kit out of the water.HB is a RC kit masquerading as a kit. Now trumpeter has come out with a late with an interior. That's completely new
@WatsonsModels24 күн бұрын
Oh I need to see that
@MrDave-bs7tc26 күн бұрын
Just purchased one of these. Half the price of a Hayward and they Sent it FEDEX. Awesome!
@WatsonsWagons26 күн бұрын
@@MrDave-bs7tc since I originally posted this video, it is still working perfectly
@olivedrabgarage624328 күн бұрын
Hey Mike..is there a link available to buy this bead splitter tool online to send to australia? I have WC combat rims to getvtyres off so I can get the wheels sandblasted.
@WatsonsWagons27 күн бұрын
@@olivedrabgarage6243 does Amazon ship there? They have a bunch of different types of
@jenniferhenry565629 күн бұрын
I bought a T15 salt cell from this company and we did everything to get it to work and it never worked. Read all the fine print before you dare to use The Salt Pool company. First red flag is they operate under several different names. Also if you have to return because it is defective you have to pay a 30% restocking fee = $108, shipping fees to you and shipping fee back to them, and then you don’t get your money back you just get store credit.
@tomreder853629 күн бұрын
watched both vids a buncha times, they REALLY helped! Thanks for putting these up!
@rileyragsdale7358Ай бұрын
Truck should have been tested, starter in to confirm issue, otherwise a guess test with scanner to see if it cranks, 90 sec. Max to test😂
@jorgenovelli7689Ай бұрын
Muy buen trabajo. Felicitaciones
@ironhorse6688Ай бұрын
Smaller drill hole
@ajwundeАй бұрын
Dude, you are the best! I fixed a leak in the heater line, spilled a bit of coolant doing it and got this exact issue. Everywhere I searched there was no mention of this burping issue. Sure enough, that's all it took to fix it. Thank you for the detailed explanation of the issue and how to fix it. Much love from Michigan.
@WatsonsModelsАй бұрын
Awesome
@MrJeep75Ай бұрын
Those seal kits don't fit A1 to big
@user-sz1qg4iy5sАй бұрын
Nice review. When the T-cell is installed horizontally the hump should be installed facing down. This ensures the plates are fully covered in water and there is no air bubble around the plates. This is particularly important with a variable speed pump at a low flow rate. The temperature sensor inside my cell failed after 3 months. Its silicone potted into the water stream and is really non-serviceable. If this happens your controller will display "HOT". I expect this is a common failing part, so Salt Pool Stores solution is to cut the red and blue wires to the thermistor inside the cell housing and wire a new thermistor to the red and blue wires running to the controller cable. Bad advice, since then it would only read the air temperature inside the housing and not the actual water temperature. You'll be back online but since the salt level is calculated by an algorithm in the main board that uses the voltage, amperage and water temperature, it will be affected by the difference between actual water temperature and measured air temperature. Best of luck to us Salt Pool Store buyers. We like it cause of price, but a thermistor failure after 3 months? Junk.
@dankreiser2592Ай бұрын
My experience is this - I ordered the cell to replace the hayward t-15 I had, and the salinity was 5200 ppm from the controller. 4200 ppm measured by the controller is actually 2700 ppm. But, I needed to have around 4000 or 4200 ppm (controller measured) in order to make enough chlorine to keep the pool clear. The calibration is off.
@tonycastro6154Ай бұрын
2:35..WEAR AND TEAR,,I WOULD SAY POTENTION SHORT,,,
@babymuffinnugget2686Ай бұрын
Silicone doesn’t absorb water.
@michaelculpepper2969Ай бұрын
Warning, Salt Pool Store Will NOT Honor a 5 Year Warranty..Also, be very Careful with the Treads on each end of the Salt Cell.. They Break off and Crumble in chunks. That Salt Cell might last you 6 months
@WatsonsModelsАй бұрын
Well that’s not so good news
@michaelculpepper2969Ай бұрын
@@WatsonsModels I have been through it Twice with them and they Turn their Back on the Customer and Never Return your Calls. They have Not Been at All Customer Oriented.. Look them up on The Better Business Bureau.. Not Good... All Horrible Complaints.
@ronnypauwels2963Ай бұрын
Ik wil dit ook reeds lang maken maar in schaal 1/15 of 1/16 en in hout ik heb ook 1/35 aangeschaft om alle stukjes na te maken 🔎ik ben zeer blij met wat jij uitlegt en zeker wat die brandstoftank de vulling plaats betreft 🔧🔩en veel meer prachtige uitleg 👍ik had tijdens mijn legerdienst veel met Willy Jeeps gereden in Siegen Duitsland lang geleden hihi.
@gregotterson6724Ай бұрын
Thank you very much for this video. I need to pull the waterpump off my 1942 Dodge WC58 Command Car, and there is very little room up there. Now I'm pretty sure it can be done.
@KT4RAMАй бұрын
Hayward Sued them and won, but they were having issues serving them even at their listed US addresses. Last that I had read the defendant never showed up. That 5-year warranty probably isn't what you might think. 30% restocking fee right off the bat on a defective unit. It says Hayward Compatible but reading that high on a Hayward chlorinator isn't exactly within a Compatible definition. Good luck. Google Salt Pool Store Complaints BBB or Pissed Customer. I'm sure wishing that i did instead of watching a couple of KZfaq videos.
@Jimmh60Ай бұрын
Your in Pa, but love the AU cap, War Eagle!
@danbaughman3042Ай бұрын
Just bought a 04 with a new water pump, I need to check for vapor lock.
@SevenBarSalvageАй бұрын
Great video just what I was looking for!
@shawdawg82Ай бұрын
I followed your video instructions tonight, it took me maybe 20 mins and now my ‘08 NorthEdition is running like a champ. Thank you!
@wernaldoproductions12152 ай бұрын
Great video! Thank you!
@campbc8072 ай бұрын
Hi - Thank you for the video. How long did shipping take? Thx!
@WatsonsWagons2 ай бұрын
Maybe a week or so
@johnnyrestrepo101323 күн бұрын
I’m having the same problem. Thanks for the video I will try it just like u did.
@davidwright45372 ай бұрын
High concentration of TSP, let sit of half an hour, flush via drain ports. If that sounds a bit to aggressive, use Iron Out in powder form. It does the trick!!!
@waynep3432 ай бұрын
On the seal groove. I wonder if a lathe tool bit that instead of a cutting tool but a ball bearing off axis could be used to roll the sides of the groove down. And if a machine shop could replicate the flange bushing with a slightly undersized bore. Or if replacement axles are cheap enough not to bother. Only issue is if an undersized bushing will slide over the splines. Oh and you could make closely matched V blocks out of 6" pieces of 2x4 to have free standing v blocks to support the axle straight while measuring. Instead of in a bind
@anthonygeiss37082 ай бұрын
That looks like it was built to last one war and then be scrapped.
@WatsonsWagons2 ай бұрын
That’s why we restore them to their original glory
@ruebencover57952 ай бұрын
I like that tool set i am going to have to get one of them 👍
@FoppingFrog2 ай бұрын
I have done (or have had done) engine (shop), transmission (shop), rear axle (me), and wiring (me). Front axle has made me nervous that it would be beyond my skill level, but it looks like something I can tackle. I am glad you are making these, I have referenced many of your videos for my projects. Most complicated was the coolant distro tube, I found the same solder blobs you did.
@WatsonsWagons2 ай бұрын
I’ll make the mistakes so you guys don’t have to. Thanks for watching.
@X-Appeal2 ай бұрын
Happy Father's Day to you too. My dad was born 16,March 1948. Also served in Vietnam. Enjoy your dad wish mine was still here.
@milcommguy59272 ай бұрын
Good job.
@WatsonsWagons2 ай бұрын
Thanks!
@leoazucena-lagos37772 ай бұрын
Happy Father’s Day to you too, and Jodi. 🥹you also don’t really know who they came from. Deployment….🇺🇸🫡
@WatsonsWagons2 ай бұрын
No Jodi, I know who my biological father is.
@milcommguy59272 ай бұрын
Good job.
@WatsonsWagons2 ай бұрын
Thanks!
@X-Appeal2 ай бұрын
I had faith you would have a video out tonight 😂 if it makes you feel any better i did this to a deuce and a half, all 6 ends. Very time consuming for sure. My M37 will be a walk in the park after that experience. Keep those videos coming.
@WatsonsWagons2 ай бұрын
Thank you
@rickdeyoung88862 ай бұрын
Damn Mike you look like a proctologist reaching in there to feel for the seal
@WatsonsWagons2 ай бұрын
Hahahahaha
@JohnCarroll-lq1ch2 ай бұрын
Yummy knuckle pudding.
@WatsonsWagons2 ай бұрын
Delish
@musketbal2 ай бұрын
The Rye Field box art shows the turret facing the wrong direction. It should have the main gun over the left side of the hull.
@WatsonsWagons2 ай бұрын
Yep
@musketbal2 ай бұрын
I was a 88 driver back in the late 80's at 24th Mechanized Infantry Division, (now 3rd I.D.), 4/64 Armor. Man diorama brings back memories. I started off with the M60A3. It would be great if one of these companies would make a M60 tank with full interior like Rye Field did with the M1.