Reliable Rocket

Пікірлер

@stevenwright6049 5 ай бұрын

Very Cool Allen!

@davesorochty 9 ай бұрын

I have used one of these coil winding tools from Reliable Rocket and they work great!

@davesorochty 9 ай бұрын

I have used one of these coil winding tools from Reliable Rocket and they work great!

@newtonspersecond Жыл бұрын

thanks for a great video ! it helped me put my 75mm 3 grain load together .

@X85283 Жыл бұрын

Your home address is visible, not sure if you know that.

@allenhall7675 Жыл бұрын

Sure, its business address just like Chris's

@hyoholdyourown6444 Жыл бұрын

where are you buying your tubular Kevlar from?

@ac2fv Жыл бұрын

Your demo shows coils that fit into a 4" rocket. Couldn't you use the harness winder to make coils that fit into smaller rockets by not winding the coils all the way? It seems that if you made marks on the winder for 3", 2.6", etc rockets, you could wind smaller coils. Am I correct in my thinking, or this will only work on rockets that are 4+"? Tnx.

@reliablerocket5398 Жыл бұрын

Certainly, Here are some photos: facebook.com/ReliableRocket/posts/pfbid02RxNxg8LhitgC9TUEtyEJaAVd9uRekMSfRj8oVfLZygzRT8Nf8DXo4R5cWW6TYLHel

@stephenschulte3996 Жыл бұрын

Excellent! I am building a MadCow Terminator-5 fiberglass rocket and will first fly it on a 5 grain Pro54 motor, but have a 4 grain Pro75 casing and will then use that with 2 spacers to launch with a 2-grain (later 3 grain) Pro75 motor. Question: Is the eyebolt on the end of the motor required? What is the use of that (to make it easier to remove the part after flight? Thanks for any comments. SCS 7 Oct 2022

@allenhall7675 Жыл бұрын

Stephen, Glad you like the video. The only purpose of the eye bolt is to attach the harness. I thought I talked (in the full length video) a little about the eyebolt dilemma in a 4 grain case (using 2 spacers) in the video, but I could have edited it out. Ultimately I purchased a 2 grain case to avoid having to use 2 spacer for the K1085.

@lostdirtknifeandtool Жыл бұрын

Do you have a link to the router bit you are using? Or one you would recommend for g10?

@StoneCold0ne1 2 жыл бұрын

Hi Allen, I cover 1 side of each with painters tape. (part & template) then apply a few drops of CA strategically placed around to secure the part to the template. (like using 2 sided tape) Very secure, easier clean up & separation with a putty knife or an Xacto blade.

@StoneCold0ne1 2 жыл бұрын

Really cool design!

@toddmichaelhorvath 2 жыл бұрын

I just launched a certification flight with a kit converted for dual deploy. Because of space constraints, I could NOT have had a successful flight without using your winder. I was even told by a kevlar supplier that I couldn’t use that size kevlar in the air frame I was using. I just laughed because he didn’t know the tool I had. Thank you for a successful flight.

@reliablerocket5398 Жыл бұрын

Hi Todd, Would you be kind enough to PM me the supplier?

@StoneCold0ne1 2 жыл бұрын

Ground testing only.