Who taught this guy how to paint?

My man, great video and editing. might want to say the size of the bolt each time you remove one

What your timing slightly off after having the heads milled down?

Isn’t this a downgrade? I was able to replace the airbags in the suspension for about 150 bucks from eBay. That was two years ago and still riding great.

I dont like when people do a continuous spray when they reach the ends of whatever they're spraying lol

Thanks fore the video. Should make my install simple. Minor annoyance: The end result in your tutorial is blocked by an advertisement.

The relaxing nature of this video gives some reassurance to tackling this DIY

I've been waiting for hair loss commercials 🧑‍🦲

Parts list?

Doing this next weekend!!! Watching your vid to install!

Finally someone does a complete air bag delete tutorial thank you so much man and very detailed video, much appreciated!

Nice Sequoia. They last forever!

PLEASE NOTE: The grille need not be yanked and should not indeed be yanked with brute force. Instead the 6 tabs should be pressed upward one at a time while releasing that side of the segment!!

Nope its not centered. Its a tad to the right. You effed up. Lol

Great video! What year Toyota wheels are those?

Almost $700 for that? No thanks. I'll get the aftermarket one for half that and use the other half for other stuff.

This was stupid easy, thanks!

Thanks for the thorough video, just did mine in about 10 minutes!

Not very helpful, the video stops halfway through the tear down, and all of a sudden you're putting the engine back together???? Didn't make any sense

is it the same process with a chrome bumper

What size sockets was the 12. Bolt to take off the cylinders head?

Is this silver or white?

Two things I’d do differently: (1) Invest in a high quality respirator, especially if you’re going to paint indoors. You’ll be surprised as to the amount of toxin the paint releases. (2) Spray the paint on a practice sheet to clear any blockage. The dip tends to block the nozzle when dried.

Not being condescending, but you should never put a led bulb in a halogen housing. 🤦🏻‍♂️🤷🏻‍♂️

Why didn't you just mask down the valence itself? Why have to peel off the coating afterwards? I don't get it.

I have a 6” lift on my F-150 and people keep flashing their high beams at me…makes me feel like a dick

Great video! I was hesitant doing it in my garage but this video helped!

Junkyards are full of the black valance

#bestuncle

What can you do if you break one of the sides of the clips holding the top grill cover, that’s mounted to the middle bumper unit?

What's the purpose of the service bolt on ex cam I didn't do that when removing and they didn't move or separate

😂thanks looks great I’ve definitely gotta do mine as well thanks 👍

Another point of advice here. When tightening the pivoting parts like the lower shock bolts and lower control arm bolts don't torque them down until the full weight of the vehicle is pressing down one them. This is because rubber bushings tightened down on without the full load on the pivoting points will break free from their surrounds inside the the shock or control arms. This is a must on any replacement suspension parts coming from me an ASE certified steering and suspension expert. So don't follow these instructions to their fullest.

Just for future reference the very first thing this guy loosened wasn't the tie rod it was the sway bar end link.

How the fuck does everyones grill pop off easy af? My middle section where the emblem is wont pop out.

did the crank pulley come off by hand or did you have to use a puller?

The spray can say that you should wait about 8 hours to apply a second hand of paint, that is crazy

How much could a shop have charged for this job?

Love it

What Trim level is your 4runner

How long did you wait between coats?

How did you change from red to black

Anyone who tries this it’s impossible to make a clear line unless your bumper or inset is a separate piece. Taping doesn’t work

💋🌟It’s OK cutie baby 🐘for you to be picky about your bananas! 😍I am the same way!!! you deserve to get the banana of your choice from these wacky doodle humans!!💋💛🥴

$6 a can? In Australia it’s $35!

😂😂😂😂😂😂😂😂 🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰

Hi, thanks for the video. What made you change the head gasket and did you have any codes after thinking i need to do this on my 2001 sequoia for a pin hole leak on the gasket..

Given the aftermarket options for around $125 or so, and being black all the eay through... would you still dip it? I've done dip on other vehicles and a forward facing piece was always the hardest to clean, you couldn't get too aggressive or you'd risk damaging it.

Could this cover a deep scratch? The plastidip

How are those Detroit Axle LCAs holding up?