PsychicKitten

Пікірлер

@EloyMatana 2 күн бұрын

Good yob you waka

@EloyMatana 2 күн бұрын

Engage at eye point

@EloyMatana 2 күн бұрын

3&4

@EloyMatana 2 күн бұрын

Youll get your chance only on broadway pon shops and dope sectors house protected animal sex slavery 10 coupons scan my qr code today army strong

@SI96k Ай бұрын

Thanks for the video. Did you have to replace any parts due to shooting the 6k+ rounds?

@Psychic_Kitten Ай бұрын

It has been reliable throughout, I haven't needed to change any parts.

@SI96k Ай бұрын

@@Psychic_KittenThanks! I was torn between saving some money and getting the fx9 4.6 inch barrel or going with the ghm9. Along with that you can replace the parts on the fx9 for way cheaper. Though it seems the ghm9 would hold up for a long time.

@Psychic_Kitten Ай бұрын

@@SI96k FX9 is good for plinking and fun shooting on the range. If you're entering IPSC or other pcc shooting competitions I'd make sure it is reliable beforehand. I'd personally get an 8+inch barrel, just from handling different barrel lengths, under 8 inches it is hard to get a good grip support side.

@SI96k Ай бұрын

@@Psychic_Kitten Thank you so much for your responses!

@mrpowerskate Ай бұрын

canadian by chance? just noticed no brace, sick gun man. wish i had the moola for this

@Psychic_Kitten Ай бұрын

Yeah i'm in Leafland. Nice thing about the GHM9 is it works out of the box, which is better than I can say for a lot of the other PCCs available (FX9s are jam machines from what I've seen).

@RubyisCute Ай бұрын

I’m looking to get the GMH9 and compete in IPSC. Should I get the 4.3, 6.9 or 18.7 inch barrel variation?

@Psychic_Kitten Ай бұрын

I'd personally get the 9 inch if possible. If not available, I'd get the 6.9 or 18.7 inch, depending on your preference. The 18.9 inch is a bit unwieldy, but has better recoil control. The 6.9 inch was slightly too short for me to get a proper grip.

Ай бұрын

Hi, my friend. I am from the Czech Republic and there is almost zero availability of any spare parts here. I have a question, can you please tell me where you bought the "folding" charging handle? Thanks a lot!

@Psychic_Kitten Ай бұрын

Unfortunately I am not in Europe, so I don't know the best source of parts in that area. I bought the B&T Folding charging handle from a distributor in my area. Perhaps you can see if you have any distributors/stores in your area that can order from B&T?

@conesack 2 ай бұрын

horrible product

@yokushund1887 2 ай бұрын

The rail is too low, you can't tilt the eotech far enought so it can jump on the rail. No idea how you got it on there without disassembling the quick attach mechanism. I put mine on a low unity riser.

@Psychic_Kitten 2 ай бұрын

I basically forced it on there. On the bright side, at least it's tight on the rail!

@shirolee 3 ай бұрын

Thank you so much for making this video!

@ROBERTMORAN-mv7eq 4 ай бұрын

Nice instructional video. Enjoyed watching. WAITING FOR DELIVERY ON MY FHM9 , SHOULD BE HERE MONDAY. GOOD LUCK WITH YOURS.

@conesack 6 ай бұрын

fantastic review, thank you very much

@82byron 7 ай бұрын

Nice video. I have almost the same setup except I’m running the B&t lower with the geissele SSP flat. Glad to see I’m not the only one who didn’t remove the metal plate on the lower. I modified my trigger the same way. Need to find time to make a video of my set up.

Ең жақсы KZfaq

Пікірлер