Video is filled with common sense basics that often get overlooked by beginners and (fast moving) experts alike. Much appreciated, and the running "tips" commentary (without annoying techno music in the background) was extra nice.
@dnslifeadventures9984Ай бұрын
Thank you so much for this information ! Could you please let us know what is the part number / name of the fan resistor that wasn’t working ? And how do you replace it ? Thanks 🙏
@nathanallen1111Ай бұрын
Thanks for the upload. My 05 sportage ran so hot that the felt pad over the coolant hose melted and started dripping down to the wire below. At first glance I thought it was the hose itself that melted. The hose is extremely hot to the touch even 5-10 minutes after car shuts off. I will ask my mechanic about thermostat and sensors.
@henningkemner18332 ай бұрын
I have a serious question. I have a Crown Vic 2009 P71. Exhaust system is stock 2in pipes with H-Pipe behind Cat. I want to mount 2 Flowmaster Straight through 71415 FlowFX behind H-pipe. Already have the mufflers. but have asked many on here for advice. No one bloody answers me. Should I reconnect the Flowmaster to the remaining stock pipe or should I go bigger? Flowmaster pipe diameter is 2,5in so I have to do a step up to fit it to stock. And step down to fit stock behind muffler. What will you recommend me doing?
@gabrielsireliangusteinhast90592 ай бұрын
You balancing a big vacuum and turbo..sequentiel
@stints1232 ай бұрын
So I have a 2014 Touareg 7P with the battery under the passenger seat... would this method still work on my model ???
@EAPerformance2 ай бұрын
Yes
@mova_20203 ай бұрын
How hard is it to also do a clean job when doing this? Like thoroughly cleaning that super dirty caliper? Inside was like a disaster. Does it cost more to do a clean job? Or is it all the same?
@rs3tuber4254 ай бұрын
Did you guys torqued the bolts?
@konsul20064 ай бұрын
What does this do to the cars battery? Would the charge cycle make the battery burn out faster due to over charging? Not a fire hazard I hope😅
@EAPerformance3 ай бұрын
No negative effects on cars that don't have auxiliary batteries like Mercedes. Mercedes use this connector to charge the aux battery but you don't have this issue on VW or Audi vehicles
@yrichard64044 ай бұрын
May i know brake pad model and part number along with the rotor tks
@Ritzys20075 ай бұрын
What are the 10-litre oil brands and oil specs can you use? also 5w-30 or 10w-40?
@EAPerformance5 ай бұрын
Best to check the oil websites, you can google search Valvoline Oil Selector for example
@gamechanger83826 ай бұрын
Great video just did mine using your video. Question is there only one brake wear sensor on the front ? Job was much more involved compared to my 996 Porsche. Rather fiddle to be honest but got it done. Caliper hardware was the most difficult but once I figured it out the other side was a breeze relatively speaking.
@venugopalthaduri30366 ай бұрын
Thank you kindly. Very detail and clear.
@joshsheinis59686 ай бұрын
Interesting… In the Audi manual they instruct you to retract the caliper and push the fluid back into the reservoir
@EAPerformance6 ай бұрын
Never ever do this on an ABS car!! It’s bad practice. If you have a chance to extract old deteriorated fluid, do it. The worst section of fluid is going to be at the caliper
@joshsheinis59686 ай бұрын
@@EAPerformance I wonder why the engineers over at Audi decided to not include that in the service manuals. They just say retract the caliper, they even go as far as saying to extract brake fluid from the reservoir if it is full because it could overflow when you push the fluid back
@EAPerformance6 ай бұрын
@@joshsheinis5968 engineers are useless half the time. Look at some of the places they put components which should be simple to replace but then make you remove the entire engine to do so.
@joshsheinis59686 ай бұрын
@@EAPerformance Yes, but, they were the ones that designed the components after all. As well as took the time to write out step by step repair/service manuals for dealerships to follow. So I would like to think they would not instruct you to do something that would damage the vehicle
@robp6968 ай бұрын
Didn't need to use brake cleaner on new rotors? Edit- Ahh I see you did mention it at the very end of the video.
@padtvanderP9 ай бұрын
Air suspension is also disabeld
@pentamotorgroup1339 ай бұрын
I got air suspension so It wont work this way?
@EAPerformance7 ай бұрын
Whilst engine running your air suspension will still work. It’s just when car is off and the auto lower when opening doors may not work. Also with Mercedes vehicles i do not recommend doing this because it drains their auxiliary battery
@lyndonodilonoy76729 ай бұрын
You’re the best 💪.. Thank you Sir 🫡
@PhatBoyiee11 ай бұрын
Do you have any break replacements videos for 2021 audi s5 b9.5?
@EAPerformance6 ай бұрын
If i get one in i will make one
@Adubs808 Жыл бұрын
thanks for this. need to do my brakes and nervous but will be rewarding
@mozerul1 Жыл бұрын
instead of bleeding the brakes , can i use obdeleven to open the calipers and close them once the new parts are in ? Cheers
@EAPerformance Жыл бұрын
HI, that is only for the rear brakes because they run an electric handbrake. The fronts dont have electric motors. But you will still need to push the piston back even after winding the motor back with your scan tool, so the bleed method is still needed.
@ax23xr Жыл бұрын
hello. great video breaking down step by step. does this process also apply for a 22 s5 Sportback?
@EAPerformance Жыл бұрын
Yes it does
@craighunter1682 Жыл бұрын
Is this the same process for an 18 plate A4 Avant?
@EAPerformance Жыл бұрын
Yes exactly same process
@darkspeed62 Жыл бұрын
Seems good, and fairly thorough. The only thing I would say is that you forgot to mention torquing the caliper bolts to the correct torque spec, and possibly adding some thread locker paste to the bolts as they're going to be prone to vibrations so wouldn't want them to work loose!
@EAPerformance Жыл бұрын
I’ve been a qualified mechanic & performance specialist for 14 years. You don’t need to worry about thread locker on any bolts around the braking system, if you look at their washers on the bolt you will see they are grooved, these are vibration proof washers. I’ve been doing this long enough to not worry about torque specs on items like this. How tight it felt undoing the bolt, do the same type of tension when doing it back up. If you’re unsure, then use the torque spec
@MacDamera4 ай бұрын
What's torque specs
@coalieroller5663 Жыл бұрын
Audi does say remove the 21mm bolts to remove the bracket and caliper instead of the special bolts to do a brake job. Good job
@as5950 Жыл бұрын
Love this. But do you have to bleed the calipers once you are all done? Planning to do this next weekend on my S5
@EAPerformance Жыл бұрын
No need to bleed, because you haven’t let any air into the system you are all good. By opening the nipple to push the piston back it is essentially bleeding it anyway
@as5950 Жыл бұрын
@@EAPerformance much appreciated. I actually followed you video to the tee. Used OEM pads (yea I know I’m just OCD like that). Zero issues. And car stops on a dime. Thanks again!
@aronmortel8213 Жыл бұрын
Sheesh
@v_m0mente2 жыл бұрын
Где Ламборгини?Почему отметил,но не показал?-_-
@largec2 жыл бұрын
Damn this joint is too sick!...this car is truly bad ass!!!
@Serius-ware2 жыл бұрын
INSANE😍😍😍
@filteaurhino2 жыл бұрын
This is one awful A90.
@DavidHernandez-yb5pz2 жыл бұрын
You mean Auschtralia?
@aRjayC282 жыл бұрын
How was the drone on highway cruising? I have stage 2 tune and looking for a good exhaust, not too loud nor droney when cruising
@KO_.2 жыл бұрын
❤
@shahali43482 жыл бұрын
What exhaust system and downpipe was installed
@EAPerformance2 жыл бұрын
This was a full TNEER exhaust system with 200cell cat
@akira59824 жыл бұрын
You need measure the height of the shims or the rockers will break under high rpm, ask me how I know 😐
@Shaolin08715 жыл бұрын
Thank you
@cman30127 жыл бұрын
where is installation process^? The name of video is unfit!
@thomasdowden30418 жыл бұрын
I Mic shim and it was. 3mm. all the flat one were. the that size
@thomasdowden30418 жыл бұрын
wat cause them to break. I am running. stock every thing and my flat shim on number 3exhaust. side keeps breaking. and throwing my rocker arm off
@EAPerformance8 жыл бұрын
I dunno why your flat one probably isnt the right size, you need to measure your valve clearances and make sure they are in spec and get the right size to get them in spec
@padraiggalvin28075 жыл бұрын
@@EAPerformance hey, not being smart but can they be measured when they have hydraulic lifters. what was the original setup.Are all flat shims and guides the same thickness?