TCM Auto Sales, LLC

Пікірлер

@daviedmx38 10 сағат бұрын

can you use a c clamp instead of the caliper tool?

@tcmautosalesllc7994 9 сағат бұрын

@@daviedmx38 Hi, it calls for a caliper tool so I would not risk using a c-clamp…the tool is free with deposit at any auto parts store.

@daviedmx38 8 сағат бұрын

@@tcmautosalesllc7994 Thanks

@keyurchauhan6771 20 күн бұрын

How should I change on the passenger side one?

@eddiecooper5986 Ай бұрын

Dont the two indentation on the piston you turned in have to be in a certain alignment

@tcmautosalesllc7994 Ай бұрын

Hi and thanks you would need to research that one but in my experience has not been an issue

@dillonsmith-6982 3 ай бұрын

Bro this video just saved me a few hundred bucks!

@mikeglover7456 4 ай бұрын

You do not need the special tool. All you have to do is put it in maintenance mode on your - and you can push it in as normal.

@user-oq7kz8lz5b 4 ай бұрын

My 2017 Fusion blows hot on driver's side, AC blows cold on right, so I pulled driver's side upper actuator, BUT that acuator controls DEFROST, VENTS,& FLOOR. So now I need fiqure out which one turns off my heat on the left side. Summer is around the corner 😢. I think there is a dual climate control actuator behind middle console 🤔?

@tcmautosalesllc7994 4 ай бұрын

Drivers side was blowing heat and passenger was blowing ice cold. I changed the actuator on drivers side and works perfect now.

@screwedupclick6647 Ай бұрын

Same problem I’m having…I have 2 in the driver 2014…I need to find the right one because the one he changed in this video control my defrost

@parrishgoodwin9874 4 ай бұрын

Thanks

@Bilinskyj 4 ай бұрын

late to the party here,,,,there are two actuators on the driver's side. One lower by the brake pedal arm and one up higher. Which one is which. my issue is the driver's side blows cold and the passenger side works normally.

@kylerayk 6 ай бұрын

CaliPer, CaliPer, CaliPer! Caliber is the size of a bullet. Please do tell where the 35mm torque tool is used. What size allen wrench? Inch or metric? So do I just go into Auto Zone and ask for a "rental kit"? Last I checked, they had a whole shelf unit full of "rental kits" for different things...ball joints, universal joints, steering wheel pullers, harmonic balancer pullers, and many others.

@tcmautosalesllc7994 Ай бұрын

Hi yes just ask autozone or parts store for brake caliber kit and they will provide the correct one

@Populationo1vr 6 ай бұрын

Thank you so much I have a question does it matter which side to replace because on mine the heater blows cold on driver side so does that mean I replace the passenger side actuator because that’s what I heard they’re vice versa I could be wrong please let me know thank you for this video so much

@tcmautosalesllc7994 6 ай бұрын

Hi, the problem that existed on my vehicle was driver side was blowing hot air and no AC…however the passenger side is much easier to access and remove.

@thebigfudge8703 6 ай бұрын

This a damn pain in the ass haha

@tcmautosalesllc7994 6 ай бұрын

Yes it is

@Robiam85 7 ай бұрын

Why does everyone keep the yellow transport lip covers on 😂

@Sable.frc1 7 ай бұрын

Monkey see monkey do

@2008Toyota_Kluger 7 ай бұрын

Black people aren’t the sharpest tools in the shed

@tcmautosalesllc7994 7 ай бұрын

This is normal where the fender scratches coming off ramps so the yellow protects..

@BlueByYou07 7 ай бұрын

Slow

@ThatSmallYoutuber 7 ай бұрын

Wow😮

@blackonblackprime 7 ай бұрын

Easiest way to get to that top screw is to start the car, have someone press and hold the break and unscrew it with a long screwdriver. Took it off in seconds

@LeftOfCenterRocks Ай бұрын

I tried this but nothing moved. It looks like it's primarily blocked by a mounted bracket that doesn't move

@blackonblackprime Ай бұрын

@@LeftOfCenterRocks that bracket is part of the brake pedal. With the car running I had my wife press the brake pedal all the way down and used a long screwdriver

@LeftOfCenterRocks Ай бұрын

@@blackonblackprime hmmm maybe I'm doing something wrong. I started the engine and pressed the brake all the way down and nothing appeared to move. I also couldn't get my hand in there any easier. Do you mean a long screwdriver from behind the bracket?

@blackonblackprime Ай бұрын

I used a long socket extension from the left side. After the brakes were fully pushed down I was able to unscrew the top screw easily. That's the only bracket that blocked the top screw for me

@LeftOfCenterRocks Ай бұрын

@@blackonblackprime I believe you, I'm just trying to figure it out. I'm in a 2016 Fusion. Same for you?

@rondomedia6924 7 ай бұрын

So how do i know which side to replace ? If my driver side is blowing hot when i have the heat on and cold on the passenger side.

@tcmautosalesllc7994 6 ай бұрын

My drivers side was blowing heat, after replacing air worked great.

@MrOkrick 8 ай бұрын

This video has ALOT of misinformation...you HAVE TO PUT THE REAR BRAKES SYSTEM INTO MAINTENANCE MODE..IT WILL ALLOW THAT CALIPER PISTON TO BE ABLE TO BE PUSHED BACK INSIDE THE CALIPER..YOU SHOULDVE EDITED YOUR VIDEO BEFORE LETTING PEOPLE THAT DONT HAVE AS MUCH EXPERIENCE WORKING ON CARS...IF YOU DONT PUT IT INTO MAINTENANCE MODE YOU WILL DESTROY THAT CALIPER..YOU CAN FIND THE INFORMATION ON RIGHT HERE..ON KZfaq. AND YOU CAN USE A C-CLAMP TO PUSH THE PISTON BACK IN OR USE NEEDLE NOSE PLIERS BY PUTTING THE TIPS OF THE PLIERS IN THE HOLES AND TURNING THE PISTON BACK INTO THE CALIPER BODY..YOU DONT NEED TO GO SPEND MORE MONEY ON TOOLS THAT YOULL PROBABLY ONLY USE TWICE IN A LIFETIME..

@tcmautosalesllc7994 9 сағат бұрын

Thanks for comment and tool is totally free…

@randyw3133 9 ай бұрын

Thanks for the information, you did a good job of describing your method for replacing the blend door on the driver's side. Helped me a lot. Took me 3 hours though trying to figure out what tool to use and how to get hands up there.

@tcmautosalesllc7994 9 ай бұрын

Yes it leaves very little space to get to but glad to hear you were able to replace!

@mrsamsung8184 10 ай бұрын

Get so many different procedures for doing the rears pads on fusions I try the emergency brake procedure thing in the freaking piston came popping out cuz I wasn't watching what I was doing and I have the toolkit like this but then you get people that say you don't need the toolkit you do it by doing the emergency brake procedure but when I was doing it the Piston was not going in it was coming out

@matthewsetzer9896 10 ай бұрын

Thanks for the video brother ,God bless from Missouri

@jayoliver7153 10 ай бұрын

What size hex key?

@windynabbie 10 ай бұрын

I believe 7mm

@waynesalekin6773 Жыл бұрын

Great video. Thank you very much

@joshhansen403 Жыл бұрын

What’s wrong with that finger

@gadisrulovitz7505 Жыл бұрын

what code did this give off ?

@tcmautosalesllc7994 Жыл бұрын

P2407 Evap Leak Detection Pump Sense Circuit

@angelavalos499 10 ай бұрын

Is there anyway you could show us the full video on how to take it off and replace

@tcmautosalesllc7994 9 ай бұрын

@@angelavalos499there were a few tabs and Phillips under the wheel well that I removed and was able to gain access. If I can’t find video will look to record and post

@waynenation678 Жыл бұрын

Never thought I'd be taking this thing out again it's a freaking hard nut to get out, and now it's only blowing from the face vent and foot vent defrost not blowing now..

@Zizie_sc Жыл бұрын

Dang.. I need one of those piston jigs. Makes the job so much easier.

@rodneybooty4011 Жыл бұрын

Thanks for posting.

@JULITOPLAYS Жыл бұрын

Thank you for this video I was about to drop $500 to have a mechanic fix it but I just searched up all the tools and everything turns out to be under $150 thank you!

@directedbytalon Жыл бұрын

500 to have your brake pads replaced? that mechanic is robbing you

@maxhuerta96 Жыл бұрын

The tools that you got did they come with the dura last gold box or no?

@tcmautosalesllc7994 Жыл бұрын

They were depart , required a deposit and once returned you get full deposit back.

@tcmautosalesllc7994 Ай бұрын

Duralast box only included brake pads and rental kit was separate you pay a deposit and it is refunded when kit is returned

@tcmautosalesllc7994 Жыл бұрын

9mths later and 2k miles still working fine😊

@jeremysmith4530 Жыл бұрын

Didn't apply grease to guide pins, brake pad ends or back of pad. Isn't it going to squeek a lot?

@tcmautosalesllc7994 Жыл бұрын

It is recommended on this vehicle I did not and 10 miles later no squeaking. Still I would recommend…thanks!

@zcsrs Жыл бұрын

Does this actuator control the door for temperature or the door for air distribution? Another youtuber said it's for the latter? kzfaq.info/get/bejne/Zrmoqa6lqrmanmQ.html

@chitowncraig Жыл бұрын

From my understanding it does both

@vitkolar 10 ай бұрын

There are two of them. In your link he's replacing the upper one, right?

@Сява-щ5ы Жыл бұрын

Good video but you don’t need a special tool to get calipers compressed, you can use a C clamp for that which is pretty cheap

@circusclown9690 Жыл бұрын

These pistons on the calipers turn instead of being compressed with a C clamp

@mrsamsung8184 10 ай бұрын

@@circusclown9690exactly

@andykolbin1783 Жыл бұрын

You don't need that special tool. All you have to do is put electronic brakes into service mode.

@rayjones5157 Жыл бұрын

On my car they still did not retract fully. Had to turn them all the way in

@maxarothdev7374 Жыл бұрын

How do you do this

@SergioHernandez-yp7hd 2 жыл бұрын

how to disable the rear brakes

@mikelitoris4028 2 жыл бұрын

So I replaced my actuator on the driver's side but the only times the gear will spin is if I either put the temperature on max AC or max Heat. Even after inserting the actuator in place, my driver's side is still warm compared to the passenger side. Any insight what the problem might be?

@tcmautosalesllc7994 2 жыл бұрын

Hello, Definitely not the news wanted to hear, it worked for me once I replaced an inserted the new one. I did have to adjust by turning on and off so the slots lined up but that was it.

@mikelitoris4028 2 жыл бұрын

@@tcmautosalesllc7994 ah I see. I was thinking maybe I don't have enough refrigerant in the system

@matt8863 2 жыл бұрын

You didn't have to put the vehicle in service mode?

@mrsamsung8184 10 ай бұрын

I did the right rear on the exact same car without doing the emergency brake procedure I just had the tool to spin in the calipers and then I went to the left rear and it would not go in all the way ended up having to get a freaking caliper because I saw the procedure for the ebrake and when I was doing it the Piston wasn't going in it was coming out and I was doing this by myself and the next thing you know the Piston came falling out and brake fluid everywhere and I had to get another caliper

@mrsamsung8184 10 ай бұрын

So I guess you can do it either way I don't know why these cars are so freaking complicated I've done hundreds of brake jobs with that tool I've never run into a problem except with a 2015 Fusion SE

@larrywhite-tk7ve 8 ай бұрын

Ok sorry I was rough on ya brother

@leepayne2596 2 жыл бұрын

Thank and yes that is f***ed up please to get to

@rickruano3919 2 жыл бұрын

That should be recalled asap!!!

@juantrainsmartnothard3505 2 жыл бұрын

Thank you so much! Saw 2 other videos and no one mentioned rhe special tools. Started the job and had to quit half way. Will rent it tomorrow. Also purchased a kit from Amazon but it arrives on the weekend. Appreciate your thoroughness!

@robertweiss9129 2 жыл бұрын

Hey buddy how are you I've seen a couple other videos on how to do this blend or actuator and I'm gonna give you up at 10 for being the most details All the others to quick talk in detail like you do I wanna thank you for a great video and you have yourself a great 2022 thanks again

@tcmautosalesllc7994 2 жыл бұрын

Thanks for checking video out and just hope it helps you.