Thank you ....i only needed to know how to get the top off to clean it. Im mot gonna do the rest of that.
@shadeburst14 күн бұрын
Thank you for the valuable advice. It should have been made possible to access the belt from below without removing the baking compartment. This machine was designed by geniuses (anyone more intelligent than me, and there are lots) but built by morons (anyone less intelligent than me, and there are lots).
@freundron4 ай бұрын
Great video! Now in 2024, those batteries get replaced by Nickel Metal Hydride (NiMH) which is a drop in replacement for NiCd, but they don't have the memory effect of the NiCds.
@jjjjjjjjjjjj2609 ай бұрын
Thank you for the detailed demonstration. I ordered my reflex plus when it first came out. used it over the years until it stop working I'm ready to replace the battery now. 😊😊😊
@wademt Жыл бұрын
Hey your video was helpful. I successfully replaced the batteries in my razor.
@loft306 Жыл бұрын
Royal pain in the butt but it's done😂. I almost took a die grinder and cut the Belt area of the bottom Off.
@winwhitmire2387 Жыл бұрын
This is a very helpful video. THESE MAY BE LITHIUM ION BATTERIES! BE VERY CAREFUL TO NOT SHORT THE BATTERY + & - LEADS AS IT COULD LEAD TO A VERY HOT FIRE! I suggest that you place electrical tape on the individual leads as you move the battery pack around. You may need a pair of "nippers" or "side cutters" to trim the battery pack leads to fit within the circuit board slots. Again...BE CAREFUL not too short the leads! A set of miniature TORX drivers will also help. Be sure to align the on/off switch as you slide the circuit board in place and secure it. Test it before you close up the shaver. Then, charge the batteries and keep an eye on the razor to make sure that they charge and don't catch fire. Again lithium ion batteries are not friendly if they catch fire! I am a HAM radio operator so I'm used to working with soldering irons, etc.
@pugekhan Жыл бұрын
Suggestion for those without soldering equipment: Silver epoxy works equally well for connecting the cut tabs of new battery and old battery, without touching the circuit board at all.
@fredfurrer1035 Жыл бұрын
Will the bottom plastic cover separate from the main plastic housing if just the five screws are removed ?
@TheWestlaker Жыл бұрын
No it won’t. There are 8 or 10 clips at the bottom holding them together, shown at 31 seconds. You need to take the pan and the metal liner out to gain access.
@nGAhGENVH0Ul Жыл бұрын
Why does the manufacturer make it so hard to access the belt? Clearly they want you to throw it in a landfill and buy another. Fucking A-holes. I'm reducing my original rating for this model for this sole reason.
@mahed822 жыл бұрын
This is painful to watch
@WisdomVendor12 жыл бұрын
I'll be cutting a section of the bottom plastic piece large enough to access the belt. It's absolutely ridiculous to have to completely disassemble something to access it's belt. What a crap design
@nGAhGENVH0Ul Жыл бұрын
It's not a crap design, it's intentional. So you go out and buy more, hopefully the same brand and model because, otherwise, you know it's a good low budget machine.
@debrac58402 жыл бұрын
Replaced the drive belt...but now it won't mix/knead
@judisinger36932 жыл бұрын
Great video. Kept mine out of the landfill. The belt on mine was rotten and wrapped around pull, not seized up. Ordering new belt and then the challenge of reassembling! Thanks again!
@TheWestlaker2 жыл бұрын
You are welcome! It’s great to hear that this helped the environment 👍 (and hopefully the crazy inflation figure)😅
@jeffvezich89362 жыл бұрын
Would this work for a phlishave 915
@hernandoherrera17643 жыл бұрын
Thanks for the video. Now I just need to find a New belt.
@nperson3 жыл бұрын
anyone know the voltage output of the transformer?
@euphgirl423 жыл бұрын
Thank you!!! I was able to replace the belt and not have to buy a new one♥️
@martinwiernusz99213 жыл бұрын
It's a pain in the BUTT to take apart the bread maker. Short cut if you don't mind.... I ended up taking a "cut-off" tool (check your tool box) and just cutting part of the bottom off. Cut around the "raised" area only (not the entire bottom as it is not needed). Right there in front of you is the belt. Easy to change.. time after time. I am sure this will void any warranty, however, if you really want to take the machine apart... go ahead and I hope that you don't have a brain aneurysm in the process :) NOTE: no wires exposed only belt and drive. JMO.
@luciafraile49893 жыл бұрын
Very well explained, thank you so much!
@kennycasey2863 жыл бұрын
AWESOME THANK YOU
@tracystoneberg53493 жыл бұрын
THANK YOU so much for this video, and your other video on how to dismantle the bread machine. Mine stopped working after 10 years and instead of buying a new one, I just replaced the belt for $12! I can't thank you enough!
@jessegolphinjr32254 жыл бұрын
Thanks for your informative video on this subject. out of all the videos on battery replacement yours was most helpful. And the further comment from SO MINT (IN THE COMMENT SECTION) added to the clarity. It helped me to revive a Norelco 965RX razor. Thanks again.
@kiefersublime4 жыл бұрын
Thanks for this video. It really helped.
@user-ie1ln6vy6e4 жыл бұрын
Is it correct to put a stronger battery and what is the way?
@johnmiller97744 жыл бұрын
Thank you. Tried to make bread and could not. Speculated that a broken belt was the cause and followed your directions via the video. Ordered the belt from eBay. Problem solved, many thanks.
@robertcaille55974 жыл бұрын
Replaced the thing for 50 buck NEW!
@nGAhGENVH0Ul Жыл бұрын
That was their goal. I did the same thing.
@rockykoast70654 жыл бұрын
A very nice clear demonstration. I just bought a second-hand AFK breadmaker. Seems like it is made by the same manufacturer. It appears the heating element is not working. Any idea where I can buy a replacement element anyone?
@rayrenzi48604 жыл бұрын
This is the exact same machine as the Accent RSH-003508-001. Thanks for the vid. I had almost destroyed the Accent machine trying to replace the drive belt. What model Sunbeam is this? (I can not find a spares list with the Accent search!)
@TheWestlaker4 жыл бұрын
Sunbeam 5891
@heinzguennewig55383 жыл бұрын
5891-33
@willkohler3794 жыл бұрын
Don't try replacing the battery unless you have moderate to advanced skill with a soldering iron.
@infiniah4 жыл бұрын
Good way to ruin the torque wrench.
@wcreswell59484 жыл бұрын
Had this machine for 4 years probably used it most to make pizza dough; usually make decent bread but the top always...always caves in no matter what I do. Now the belt broke and what a pain to remove all those screws to get at the belt. Review companies...NEVER EVER talk about ease of doing this job which is like a brake job on your car...it will need to be done someday. The good news is that I now have a replacement motor, circuit board, and bread pan and this is still the cheapest maker out there. Oh, I get around the crappy loaf by just using the machine for dough and then putting it in the oven in real bread loafs and letting the bread to the final there. Not going to spend $200 for a fancy one that probably has the same problems...but I expect most have an easier way to replace the belt... at least I hope. Thanks for a good short no nonsense video without going into a long dissertation on you know...everything else that is less important.
@debrac58402 жыл бұрын
I pulled the ingredient out of the container, mixed and kneaded by hand put it in a cast iron skillet and baked in the oven !!
@nGAhGENVH0Ul Жыл бұрын
I have never had one loaf cave in, and I must've done over 200 before the belt went kaput because they're cheaply built, but when they work they work (you need to experiment to get the right balance of ingredients to this specific model). You can consider buying a near broken machine for pennies for replacement parts, but is it worth your time and hassle?
@pattimichellesheaffer1035 жыл бұрын
where do you get the belt?
@rosskrause39265 жыл бұрын
I like the video here,but nobody ever gives the specs on the replacement batteries they use in their repair jobs..always only say "buy a spot-weld replacement pack".
@karenbearden61985 жыл бұрын
Thank you so much! If not for your video I would not have been able to repair my machine and I appreciate it.
@olo-burrows5 жыл бұрын
Great, the hard part of actually disassembling the housing is NOT INCLUDED IN THIS VIDEO. Why bother??
Well, I am really sorry I watched your video. I wasted $8 on battery pack & screwdriver. I had zero luck removing the solder. My gun is NOT magic, so it would NOT remove the tabs. My vacuum pump would NOT remove the solder. So, after 45 minutes or wresting with it, I broke a gold tab. Should have thrown the shaver in the trash & moved on & not had a very frustrating afternoon..
@erezs56925 жыл бұрын
I know the length is about 537mm,What is the top width of the belt?
@leiliu65505 жыл бұрын
It is a great help. thanks a lot!
@cackleberry63176 жыл бұрын
I bought this bread maker second hand it to Goodwill and it worked OK but was leaving rubbery bits underneath of it. So I decided to take it apart to replace the belt. Your video has been most helpful. Sunbeam corporation not so much. It’s like they deliberately designed this thing so that the part most likely to need replaced was the hardest part to get to. They could have made this thing with a snap on base so that one could replace the belt like one might replace a battery.
@eardisimone4 жыл бұрын
Hello, i have the same experience where did u purchase the belt? Thanks
@judisinger36932 жыл бұрын
Exactly. Other brands appear to be easier to access belt!
@nGAhGENVH0Ul Жыл бұрын
Sunbeam, you're fucking assholes.
@jimdarby59086 жыл бұрын
Fine video. Replacing my batteries very soon and this video will definitely help.
@arnoniem6 жыл бұрын
Worked for me!
@100PercentOS26 жыл бұрын
May I ask how old your bread maker is?
@TheWestlaker5 жыл бұрын
12 or 13 years maybe. More importantly I think it's the number of uses which is probably 20 times before the original belt gave up.
@100PercentOS26 жыл бұрын
I would like to know how to disassemble a Welbilt ABM 100-3 Bread Machine so I can replace the belt.
@bozscaggzz74756 жыл бұрын
Oh my God, there is so much wrong with this.
@carthychan8206 жыл бұрын
Thanks for this video. Have you had an issue with the paddle spindle becoming loose? My spindle falls out and liquid now leaks out of the pan. I'm not sure if a c-clip(s?) has gone missing or if the bushing has worn and is now too loose to hold the spindle in place. What do you recommend? Maybe just buying a new pan altogether? Thanks!!
@TheWestlaker6 жыл бұрын
Guess what, that happened to me two weeks ago when I was making a very hard dough. I found this link www.instructables.com/id/Kenwood-Bread-Maker-BM-450-Bread-Pan-Shaft-Seal-Re but am not 100% sure whether the Sunbeam pan uses the same design/component.
@TheWestlaker6 жыл бұрын
Nevertheless, if you look at this ebay seller's stuff (www.ebay.com/gds/How-to-install-a-new-breadmaker-pan-shaft-seal-/10000000175092691/g.html), it seems to confirm the instructables' article.
@carthychan8206 жыл бұрын
Thanks for reply. I think the cir clips have actually worn out or broke away. As it turns out the bread pan is the same one used by a few brands. Second hand stores have whole shelves of barely used machines. I picked up a Hamilton Beach for $15 and using the pan in my Sunbeam for now. Cheaper than buying parts and less effort than repairing :D I have tweaked many recipes to bake properly in the Sunbeam, so I will continue using it till it dies. I do appreciate your video though.
@kathymcdonald82276 жыл бұрын
Thank you. This helped lots in disassembly and reassembly. May I suggest next time to place the words on a place in the video that doesn't cover what you are doing. Thanks again. I appreciate this. Saved me $50 for a new bread maker!!
@TheWestlaker6 жыл бұрын
thanks for the feedback! You also saved several pounds of plastic/electronics from entering a landfill. That is cool!
@Batteriesinaflash6 жыл бұрын
Great instructions video on how replace a an old Norelco Razor battery with a new Exell Battery EBR-2. You find find the battery at the link below. www.batteriesinaflash.com/2-4v-razor-battery-replaces-braun-2000-norelco-3000-remington-8b11l
@ajacobs1007 жыл бұрын
Next time do a video on how to cut your fking nails.
@buzzclark7 жыл бұрын
Hi. & thank you for showing this procedure. I guess the hardest part is having to solder into place the connections. I learned so much from your video. I have 3 Norelco shavers so there will at some time be necessary for me to replace the battery pack. Thank You. Sincerely, JAMES.